DL manuals
Loctite
Power Tool
175
Operation Manual

Loctite 175 Operation Manual

Other manuals for 175: Operation manual

Manual is about: Hot Melt Dispenser 120 Volt Part Number 98035 230 Volt Part Number 98055

Page of 11

Download

Print this page

Bookmark us

O P E R A T I O N M A N U A L

EQUIPMENT

Hysol 175

P/N 98035

Loctite is a trademark of Loctite Corporation, U.S.A.

Data in the manual is subject to change without notice.

985132 06/01

Loctite Brazil

Av. Prof. Vernon Krieble, 91

06690-11-Itapevi

São Paulo-Brazil

Loctite Americas

1001 Trout Brook Crossing

Rocky Hill, CT 06067-3910

Loctite Canada Inc.

2225 Meadowpine Boulevard

Mississauga, Ontario L5N 7P2

Loctite Company de México, S.A.d e C.V.

Calzada de la Viga s/n, Fracc. Los Laureles

Loc. Tulpetlac, C.P. 55090

Ecatepac de Morelos, Edo. de México,

México

www.loctite.com

A Company

1 2 3 4 5 6 7 Next › »

Summary of 175

Page 1
O p e r a t i o n m a n u a l equipment hysol 175 ® p/n 98035 loctite is a trademark of loctite corporation, u.S.A. Data in the manual is subject to change without notice.  copyright 2001. Loctite corporation. All rights reserved. 985132 06/01 loctite brazil av. Prof. Vernon krieble, 91 06690-11-it...
Page 2
Page 1 contents 1. Please observe the following.................................................................................. 2 1.1. Safety ......................................................................................................................... 2 1.2. Items supplied................
Page 3
Page 2 1. Please observe the following 1.1. Safety do not touch the nozzle or molten adhesive with bare skin as they are hot - the operating temperature of the loctite ® hysol ® 175 is approximately 400ºf (200ºc). Protective gloves should always be worn. Careless handling can cause skin burns. If mo...
Page 4
Page 3 4. Installation before using the tool for the first time check it carefully for signs of external damage. If any shipping damage is found do not use the tool - return it to your supplier immediately. Steps 1 – 5 should be followed before connection to the main supply: 1. Locate the enclosed s...
Page 5
Page 4 5.1. The auto standby feature with a tool as powerful as the loctite ® hysol ® 175 there would be a risk of adhesive ‘meltdown’ if it were left unused for too long at its normal operating temperature. To avoid this a special standby function is built into the temperature controller, lowering ...
Page 6
Page 5 7. Troubleshooting before proceeding with any repair or maintenance operation disconnect the tool from the main electricity supply. If the adhesive cartridge does not advance when the trigger is pulled, check that the tool is plugged into the main supply, switched on, and has had sufficient t...
Page 7
Page 6 8. Care and maintenance • when in use, do not lay the tool on its side - always place upright using the stand provided. • do not use excessive force on the trigger. Ensure that the tool has fully warmed up before use. • keep the nozzle clean to prevent adhesive build-up. This is easily done b...
Page 8
Page 7 accessories part number nozzle 1-hole kit, qty 5, 0.080” (2 mm) orifice 985225 nozzle 2-hole 985110 nozzle 3-hole 985111 extension nozzle 0.120” (3 mm) 985112 needle extension nozzle 0.050” (1.3 mm) 985113 spreader extension nozzle 0.250” (6 mm) 985114 ‘l’ nozzle, overlap carton sealing 98511...
Page 9
Page 8 11. Appendix pictures of available nozzles/accessories. 985087 heavy duty free-standing metal stand 985243 tool hanger / balancer 985110 2 hole 985111 3 hole 985112 extension 985113 needle 985114 spreader 985115 ‘l’ nozzle 985225 1 hole 985116 ‘t’ nozzle 985088 nozzle adaptor.
Page 10
Page 9 12. Exploded diagram..
Page 11
Page 10 13. Parts list. 51 1 main capacitor assembly 985178 50 1 torsion spring 49 1 helical spring lock washer heater housing kit 985221 48 1 snubber screw feed bar kit 985220 47 1 earth (ground) screw heater housing kit 985221 46 1 feed bar plunger screw 45 1 feed bar handle screw feed bar kit 985...