Equipment operation manual loctite ® 175 hot melt dispenser 120 volt part number 98035 230 volt part number 98055 rohs compliant label p/n 8900605 120v, 50/60hz 400w 175 dispenser p/n: 98035 label # 985029.
Table of contents 1 please observe the following .....................................................................3 1.1 e mphasized s ections ......................................................................................................3 1.2 s afety .........................................
1 please observe the following 1.1 emphasized sections warning! Refers to safety regulations and requires safety measures that protect the operator or other persons from injury. Caution! Emphasizes what must be done or avoided so that the unit or other property is not damaged. Notice: provides recom...
2 description the loctite ® 175 hot melt dispenser contains a powerful 400w stainless steel cartridge heater which, in conjunction with it’s adjustable solid-state electronic controller, provides both a fast 5-minute warm-up, and accuracy in temperature control to within +/- 10°f (5°c) of the set te...
4 installation before using the tool for the first time check it carefully for signs of external damage. If any shipping damage is found do not use the tool - return it to your supplier immediately. Steps 1 –5 should be followed before connection to the main power supply: 1. Assemble the enclosed st...
5 operation normal use: assemble the stand and place the tool in an upright position on a flat surface. plug the tool into the power supply socket, and switch on the power. wait 5 minutes for the tool to reach its normal operating temperature. squeeze the trigger to advance the handle/plunge...
6 application hints as with all adhesives, performance depends on conditions of use. Suggestions or recommendations contained herein are for guidance only, since actual conditions of use are outside the supplier’s control. Ensure that the surfaces to be bonded are dry, free from dust, grease, and lo...
7.2 feed mechanism adjustment this is factory set and should not require adjustment until the tool has been in use for some time. This adjustment compensates for any wear or slackness in the trigger movement. Typically free play at the trigger tip should be 0.3 –0.4”(8 - 10mm). To re-set, insert a 2...
9 accessories and spare parts spare parts part # spare parts part # complete nozzle check adapter assembly nozzle check adapter only (included with 985078) temperature control 110/120v (includes: pc board, tco, micro switch, temp sensor temperature control 230v (includes: pc board, tco, micro switch...
9 accessories and spare parts (continued) accessories part number standard nozzle 1-hole kit, qty 5, 0.080”(2mm) orifice nozzle 2-hole nozzle 3-hole extension nozzle 0.120”(3mm) needle extension nozzle 0.050”(1.3mm) spreader extension nozzle 0.250”(6mm) “l”nozzle, overlap carton sealing “t”nozzle, c...
11 exploded diagram.
12 parts list item qty description rebuild kits available part no. 51 1 main capacitor assembly, 120v main capacitor assembly, 230v 985178 985757 50 1 torsion spring trigger kit 985540 49 1 helical spring lock washer heater housing kit 985221 48 1 snubber screw feed bar kit 985220 47 1 earth (ground...
13 warranty henkel expressly warrants that all products referred to in this instruction manual under loctite ® 175 hot melt dispenser (hereafter called "products") shall be free from defects in materials and workmanship. Liability for henkel shall be limited, as its option, to replacing those produc...
Henkel corporation one henkel way rocky hill, ct 06067-3910 henkel canada corporation 2515 meadowpine boulevard mississauga, ontario l5n 6c3 henkel capital, s.A. De c.V. Calzada de la viga s/n fracc. Los laureles loc. Tulpetlac, c.P. 55090 ecatepac de morelos, edo. De méxico henkel corporation autom...
