1. DL manuals
  2. Logan Graphic Products
  3. Power Tool
  4. Pro Joiner Model F300-2
  5. Instruction Manual

Logan Graphic Products Pro Joiner Model F300-2 Instruction Manual

Summary of Pro Joiner Model F300-2

  • Page 1

    Description the pro joiner model f300-2 has been designed as a full featured manual joiner that is easy to use. Features include alignment pins which will correctly drive v-nails into all woods, fully adjustable press for variable moulding sizes and shapes, adjustable v-nail spacing allowing you to ...

  • Page 2: Identification

    Identification instruction manual model f300-2 pro joiner v-nails - moulding fasteners. Lever - arbor press handle used to drive clamped moulding on to v-nails. Lever adjustment block - block which moves to locate pressure foot and adjust lever height. Moulding spacer - helps in driving awkward prof...

  • Page 3: Instruction Manual

    Instruction manual model f300-2 pro joiner parts list extension arms 2 extension arm screws 4 extension arm wrench 1 moulding spacer 1 pro-joiner 1 v-nail slider 1 v-nails 400 parts list pro-joiner v-nail slider v-nails extension arm screws moulding spacer extension arms extension arm wrench 2 logan...

  • Page 4: Instruction Manual

    Instruction manual assembly procedure a. Extension arms 1. Align set of holes in arm with holes in vise, making sure the rubber bumper faces up. (fig. 1). 2. Attach arm to vise with extension arm screws using extension wrench supplied. Fig. 1 model f300-2 pro joiner preparation a. Clamp moulding • m...

  • Page 5: Instruction Manual

    Instruction manual model f300-2 pro joiner preparation continued b. Set v-nail spacing 1. Read dimension from vise scale (fig. 7). 2. Adjust v-nail block in slider to same dimension as vise scale. V-nails are now set approximately 1/4 inch from each end of joint (fig. 8). 3. Replace slider. V-nail c...

  • Page 6: Instruction Manual

    Instruction manual pro joiner model f300-2 preparation continued c. Set pressure foot over moulding 1. Loosen lever adjustment block handle. 2. Adjust lever adjustment block so pressure foot locates over middle moulding or where even downward pressure can be applied (fig. 10). 3. Tighten lever. 4. D...

  • Page 7: Instruction Manual

    Instruction manual model f300-2 pro joiner operation a. Load v-nails 1. Remove slider from base board (fig. 13). 2. Decide to drive one or two v-nails. With some hardwoods (wal- nut, etc) it may be easier to press only one v-nail in at a time. 3. Insert v-nail with sharp edge up onto pins oriented t...

  • Page 8: Instruction Manual

    Instruction manual model f300-2 pro joiner trouble shooting problem solution gaps in joints. Sand mitres smooth. Make sure the two pairs are equal length. Reduce the amount of glue in joint. Check square cutting action of saw. Use longer v-nails if possible. V-nails don’t drive in all the way in. Tr...

  • Page 9: Instruction Manual

    Instruction manual model f300-2 pro joiner 8 logan graphic products inc., 1100 brown street, wauconda, il 60084 toll free 1 800 331 6232 www.Logangraphic.Com no. Description qty. L124 feet 4 l124n ext. Arm bumper 2 l348n knob screw 3 l804n2 handle spring 1 l828 post washer 6 l853n ext. Arms 2 l854 b...

  • Page 10: Instruction Manual

    9 logan graphic products inc., 1100 brown street, wauconda, il 60084 toll free 1 800 331 6232 www.Logangraphic.Com instruction manual model f300-2 pro joiner no. Description qty. L348n knob screw 1 l838 slide block tension screw 1 l860n5 pin block 2 l861n pin holder 2 l862n2 slide block small 1 l863...

  • Page 11: Instruction Manual

    A l s o a v a i l a b l e f r o m l o g a n g r a p h i c s logan graphics picture framing system includes all the tools and accessories you need to produce professional quality frames including… 10 logan graphic products inc., 1100 brown street, wauconda, il 60084 toll free 1 800 331 6232 www.Logan...