Macro-Tech 24x6 Reference Manual - page 31
Page 31
Macro-Tech 24x6 & 36x12 Power Amplifiers
CLP
Programmable
Input Processor (P.I.P.)
3
1
2
GND
I N P U T
I N P U T
C H - 2
C H - 1
PUSH
PUSH
P.I.P.–CLP
detects and prevents overload. Its compressor is
driven by the amplifier’s built-in
IOC
error detection circuitry.
Unlike typical signal-driven compressors, it only compresses
the signal to prevent overload. It can deliver up to 13 dB of
additional headroom without being noticeable.
ISO
Programmable
Input Processor (P.I.P.)
—WARNING—
THIS P.I.P. PROVIDES FULL ISOLATION
FOR ISO-MODIFIED AMPLIFIERS ONLY!
DO NOT CONNECT THE OUTPUT GROUND
LUG TO THE INPUT COMMON OR CHASSIS
GROUND. REFER TO P.I.P.–ISO OWNER’S
MANUAL FOR FURTHER INFORMATION.
+
–
C H - 2 I N P U T
+
–
C H - 1 I N P U T
P.I.P.–ISO
is designed especially for 25 to 140 volt distrib-
uted systems where UL
®
-listed isolation is required. Installa-
tion requires minor amplifier modifications. With the P.I.P.–ISO
installed, the amplifier outputs are safely isolated from the
input terminals and the chassis.
Programmable
Input Processor (P.I.P.)
+
–
–
ATTENUATION
ATTENUATION
ATN
B
C H - 2 I N P U T
C H - 1 I N P U T
0
dB
.5
1
2
3
4
5
6
7
8
10
12
14
16
18
20
22
24
28
60
∞
0
dB
.5
1
2
3
4
5
6
7
8
10
12
14
16
18
20
22
24
28
60
∞
+
P.I.P.–ATNB
uses balanced 1:1 transformers to isolate the
amplifier from the input signal. It also includes 12 dB/octave
RFI filters, variable 18 dB/octave high-pass filters, and 6 dB/
octave 3 kHz shelving networks for “constant-directivity” horn
equalization. The module also includes a calibrated 21-step
precision attenuator for each channel. Screw terminal plugs
are provided for input.
Programmable
Input Processor (P.I.P.)
3
1
2
GND
PUSH
XOV
O U T P U T S
I N P U T S
+
–
TIP
RING
SLEEVE
GND
P.I.P.–XOV
is a versatile 18 dB/octave mono crossover/filter
with biamping and triamping capabilities
Programmable
Input Processor (P.I.P.)
3
1
2
GND
PUSH
PUSH
FMX
C H - 2 I N P U T S
C H - 1 I N P U T S
P.I.P.–FMX
facilitates “daisy-chaining” balanced amplifier in-
puts. Female to male three-pin XLR connectors are used to
passively bridge the inputs.
PA
Programmable
Input Processor (P.I.P.)
+
–
+
–
LINE
MIC
MIC
LEVEL
C H - 2 I N P U T S
CH-2
CH-1
REMOTE
+
–
+
–
MIC
LINE
MIC
LEVEL
C H - 1 I N P U T S
P.I.P.–PA
adds a switchable balanced low-impedance mic
input, a balanced line-level input and a compressor to each
channel. Remote switching circuitry provides quick and quiet
fades from mic to line and back.
+
–
+
–
OUT
C H - 2
+
–
+
–
IN
OUT
C H - 1
BEQ
Programmable
Input Processor (P.I.P.)
IN
P.I.P.–BEQ
is a two-channel module providing equalization
for BOSE
®
loudspeakers. For example, the P.I.P.–BEQ can
be used in place of a BOSE 102 controller. Screw terminal
plugs provide balanced connections. Each input channel
has an output from the
P.I.P.
that can be independently con-
figured for output with no processing, loudspeaker equaliza-
tion or loudspeaker equalization with bass-cut.
RPA
Programmable
Input Processor
+
– +
–
MIC
LINE
PHAN
TIE
RMT B
RMT A
OUT
IN
OUT
IN
RMT C
RMT D
+1
0 V
A U D I O B U S
CH-2
CH-1
MIC
LINE
PHAN
INPUT D
(CH-2)
INPUT C
(CH-2)
+
– +
–
MIC
LINE
PHAN
MIC
LINE
PHAN
INPUT A
(CH-1)
INPUT B
(CH-1)
LEVEL
LEVEL
P.I.P.–RPA
adds the features of a 4x2 mixer to your amplifier.
Its four inputs accept mic- or line-level input. It offers priority
switching (“voice-over”) of each input and remote level con-
trol with the RPA–RMT. Other features include bus inputs and
outputs, adjustable input sensitivity, phantom power and RFI
suppression. Input isolation transformers are optional.
For more information on these or other
P.I.P.s under
development, contact your local dealer or Crown’s
Technical Support Group.