Summary of MPC-200
Page 1
1 user’s manual fast ethernet cardbus (mpc-200) r acsense.
Page 2
Table of contents chapter 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 network interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 3
Chapter 1 introduction this manual describes how to operate the fast ethernet cardbus card. The fast ethernet lan pc card is a credit-card sized ethernet card which works with any comput- er, notebook, sub-notebook or macintosh powerbook g3 series, or card reader that sup- ports cardbus slots. Cardb...
Page 4
¥ bus width: 32 bits ¥ power: 3.3 v ¥ temperature: 0ûc~60ûc/ 32ûf~140ûf (std. Operating) ¥ humidity: 10% to 90% ¥ distance: 100m from hub to node ¥ dimensions: 86mm x 54mm x 5 mm installing the fast ethernet cardbus card you will be installing the fast ethernet cardbus card in your computer. If you ...
Page 5
Chapter 2 getting started installing the fast ethernet cardbus card you will be installing the fast ethernet cardbus card in cardbus slot of your computer. If you have trouble locating the slot, please refer to your computer's user manual or consult the dealer of your computer. Follow the procedure ...
Page 6
Led indicators ¥ 100 led: this led is used to indicate the ethernet speed: the green light indicates a connection with a 100base-tx fast ethernet network . ¥ link/act led: this led is used to indicate the network activity. It is blinking when the pc card is transmitting or receiving packets from net...
Page 7
Chapter 3 driver installation for mac os system requirements ¥ mac os version 8.1 or above. ¥ macintosh g3 powerbook series. ¥ card and socket service 3.0. ¥ open transport 1.3 or above installation before your computer system can recognize your fast ethernet cardbus card, it is necessary to run som...
Page 8
4. Click the install button. The installer will install the appropriate driver to your com- puter. 5. Click the restart button when installation is completed. Appletalk setup ¥ open the appletalk control panel ¥ select fastether card from the pop-up menu. Optional: the current zone pop-up menu will ...
Page 9
¥ close the control panel when you have finished. ¥ to confirm the change of network connections, click ok . Tcp/ip setup ¥ open the tcp/ip control panel. ¥ select fastether card from the pop-up menu. . ¥ set up tcp/ip configuration according to the situation of your network environment. ¥ close the...
Page 10
¥ drag the fastether card icon that appears on the desktop to the trash. ¥ then the fastether card will eject automatically. Chapter 3 driver installation for mac os 8.
Page 11
Appendix a specifications ¥ network standard: 10mbps ieee 802.3 10base-t ethernet 100mbps ieee 802.3u 100base-tx fast ethernet ¥ type ii pcmcia, hot plug-and-play fast ethernet cardbus card, supports full duplex 10base-t and 100base-tx communication ¥ complies with 32-bit pci card bus specification....
Page 12
Appendix b pin assignment rj-45 connector the rj-45 connector is used to connect with a hub or switch, rj-45 regular ports can be attached to any devices which use a standard network interface (e.G., a workstation, server, bridge or router). Rj-45 up-link ports can be cascaded to a station port on s...
Page 13
Copyright copyright © 1998 by this company. All right reserved. No part of this documentation may be reproduced in any form or by any means or used to make any directive work ( such as translation or transformation ) without permission from macsense connectivity, inc. . Macsense connectivity, inc. R...