P6lx-atx p6lx-atx isa/pci/io isa/pci/io mother board mother board user’s manual user’s manual part no. M527g00100 rev 1.0 nov. 1997.
________________________________________________________________________________________ p6lx-atx m/b manual page 1 table of contents table of contents page 1. Specification …………………………………………………. 2 2. Jumper & memory setting …………………………………… 3 2.1 cpu jumper setting 3 2.2 special function jumpers ……………...
Page 2 p6lx-atx mb manual specifications specifications 1. P6lx-atx specifications cpu cpu intel pentium ii cpu speed 233/266/300mhz system speed 66mhz bios bios 128k bios; pnp compliant bios rom flash memory memory dram size from 8m up to 384m bytes dram module dimm x 3 of 168 pins data path 64 bit...
________________________________________________________________________________________ p6lx-atx m/b manual page 3 jumper setting jumper setting 2. Jumper & memory setting 2.1 cpu jumper setting cpu speed (jp2) a b c d 333mhz off off on on 300mhz off on off on 266mhz off on on on 233mhz on off off ...
Page 4 p6lx-atx mb manual jumper setting jumper setting 2.3 multifunction connector cm o s c l e a r a t x p o w e r p o w e r l e d / k e y l o c k e x t _sm i r e s e t sp e a k e r h d d 2.4 memory size l l168 pin dimm 168 pin dimm option type dimm1/2/3 8m, 16m, 32m, 64m, 128m note : 1 the dram i...
________________________________________________________________________________________ p6lx-atx m/b manual page 5 jumper setting jumper setting pin (5) post (6) (1) (2) attach mount pentium ii retention module (item3) captive nut lock holes (3) top bar (4) heat sink support base top bar (item4-7) ...
Page 6 p6lx-atx mb manual jumper setting jumper setting 2.6 installing the pentium ii processor: 1. Mount the pentium ii retention module: place the retention module over the sec slot with the retainer’s lock holes toward the motherboard’s memory slots and screw the captive nuts using a flat head sc...
________________________________________________________________________________________ p6lx-atx m/b manual page 7 jumper setting jumper setting 2.7 chart of jumper winbond w839771f pci1 pci2 pci3 agp slot1 dimm3 dimm2 dimm1 jp2 abcd intel 82371 intel 443lx atx-power power fan cpu fan jp10 jp11 fla...
Page 8 p6lx-atx mb manual 3. Award bios setup 3.1 bios setup the motherboard supports 5v programmable flash rom chips. These memory chips can be updated when bios upgrades are released. Use the flash memory writer utility to download the new bios file into the rom chip as described in detail in this...
________________________________________________________________________________________ p6lx-atx m/b manual page 9 award bios setup award bios setup load defaults the “load bios defaults” option loads the minimized settings for troubleshooting. “load setup defaults ”, on the other hand, is for load...
Page 10 p6lx-atx mb manual aword bios setup aword bios setup 3.2 standard cmos setup this “standard cmos setup” option allows you to record some basic system hardware configuration and set the system clock and error handling. If the motherboard is already installed in a working system, you will not ...
________________________________________________________________________________________ p6lx-atx m/b manual page 11 award bios setup award bios setup date to set the date, highlight the “date” field and then press the page up/page down or +/- keys to set the current date. Follow the month, day and ...
Page 12 p6lx-atx mb manual award bios setup award bios setup for ide hard disk drive setup, you can: • use the auto setting for detection during bootup. • use the ide hdd auto detection in the main menu to automatically enter the drive specifications. • enter the specifications yourself manually by ...
________________________________________________________________________________________ p6lx-atx m/b manual page 13 award bios setup award bios setup floppy 3 mode support (disabled) this is the japanese standard floppy drive. The standard stores 1.2mb in a 3.5” diskette. This is normally disabled ...
Page 14 p6lx-atx mb manual award bios setup award bios setup 3.3 bios features setup this “bios features setup “ option consists of configuration entries that allow you to improve your system performance, or let you set up some system features according to your preference. Some entries here are requ...
________________________________________________________________________________________ p6lx-atx m/b manual page 15 award bios setup award bios setup cpu card l1 cache (enabled) this fields allow you to choose from the default of enable or choose disable to turn on or off the cpu’s level 1 built-in...
Page 16 p6lx-atx mb manual award bios setup award bios setup 3.4 chipset features setup this “chipset features setup” option controls the configuration of the board’s chipset. Control keys for this screen are the same as for the previous screen. Dram speed selection (60ns dram) the default setting o...
________________________________________________________________________________________ p6lx-atx m/b manual page 17 award bios setup award bios setup 8-bit i/o recovery time (1 busclk) this option specifies the isa back to back cycle. Some isa cards need long recovery time. 16-bit i/o recovery time...
Page 18 p6lx-atx mb manual award bios setup award bios setup 3.5 power management setup the power management setup screen enables you to control the mainboard green features. See the following screen. Power management (enabled) this function allows you to set the default parameters of power-saving m...
________________________________________________________________________________________ p6lx-atx m/b manual page 19 award bios setup award bios setup modem use irq (3) you can set irqs 3, 4, 5, 7 individually through modem. Activity detected from any irq channel will wake up the system. Doze mode (...
Page 20 p6lx-atx mb manual award bios setup award bios setup resume by ring (disabled) enabled this item allows computer to be turned on remotely through a modem. Resume by alarm (disabled) enabled this item allows your system to automatically boot in specific time. Irq[3-7, 9-15] to enable or disab...
________________________________________________________________________________________ p6lx-atx m/b manual page 21 award bios setup award bios setup 3.6 pnp/pci configuration setup the pnp/pci configuration setup allows you to configure the isa and pci devices installed in your system. The followi...
Page 22 p6lx-atx mb manual award bios setup award bios setup primary ide int# secondary ide int# these two items, in conjunction with item “pci ide irq map to”, specify the irq routing of the primary or secondary channel of the pci ide add-on card(not the onboard ide). You must specify the slot in t...
________________________________________________________________________________________ p6lx-atx m/b manual page 23 award bios setup award bios setup 3.7 load bios defaults this “load bios defaults” option allows you to load the troubleshooting default values permanently stored in the bios rom. The...
Page 24 p6lx-atx mb manual award bios setup award bios setup on-chip primary pci ide (enabled) on-chip secondary pci ide (enabled) these parameters lets you enable or disable the ide device connected to the primary/secondary ide connector. Ide primary master pio (auto) ide primary slave pio (auto) i...
________________________________________________________________________________________ p6lx-atx m/b manual page 25 award bios setup award bios setup onboard print port (378/irq7) this item controls the onboard printer port address and interrupt. Print port mode (spp) this item lets you set the par...
Page 26 p6lx-atx mb manual award bios setup award bios setup 3.10 supervisor password and user password these two options set the system passwords. “supervisor password” sets a password that will be used to protect the system and the setup utility; “user password” sets a password that will be used e...
________________________________________________________________________________________ p6lx-atx m/b manual page 27 award bios setup award bios setup remember that if you are using another ide controller that does not feature enhanced ide support for four devices, you can only install two ide hard ...
