1. DL manuals
  2. Magnetic Autocontrol
  3. Controller
  4. MGC-PRO
  5. Technical Manual

Magnetic Autocontrol MGC-PRO Technical Manual

Other manuals for MGC-PRO: Technical Manual
Manual is about: MicroDrive Ethernet Module

Summary of MGC-PRO

  • Page 1

    Technical manual ethernet module mgc-pro microdrive this technical manual is a supplement to the operating instructions "barrier mhtm tm microdrive" (5815,5001) and describes the ethernet module. Before using the ethernet module, read this handbook and the operating instructions "barrier mhtm tm mic...

  • Page 2: Contents

    Ethernet module mgc-pro microdrive contents 5815,0001en / version 00 contents 1 general....................................................................................5 1.1 information regarding the technical manual ..................5 1.2 function ..................................................

  • Page 3: 1 General

    Ethernet module mgc-pro microdrive general 1 general 1.1 information regarding the technical manual this manual offers important information on handling of the ethernet module. The ethernet module can only be operated installed in the magnetic mhtm tm microdrive barriers. Prerequisite for secure wor...

  • Page 4

    Ethernet module mgc-pro microdrive general 1.3 reference documents note! This technical manual is based on the documents listed in the following table. All listed reference documents are available free of charge via the indicated procurement source. Number title author procurement source 5815,5001 o...

  • Page 5: Notice!

    Ethernet module mgc-pro microdrive general 1.4 pictogram explanation warning notes warning notes are characterised by pictograms in this manual. It is absolutely essential to observe the notes and to proceed with caution in order to prevent property damage. Notice! Notice! … points to a potentially ...

  • Page 6: 2 Technical

    Ethernet module mgc-pro microdrive technical data 8 5815,0001en / version 00 2 technical data designation unit value current consumption ma 50 data transfer rate mbit/s 10 /100 max. Line length: m 30 cable type – cat-5, twisted pair plug type – rj-45 default ip address – 192.168.1.2 supported servic...

  • Page 7: Notice!

    Ethernet module mgc-pro microdrive installation and network connection 3 installation and network connection 3.1 installing ethernet module in control unit mgc-pro hints and recommendations note! The ethernet module can only be operated with the magnetic control units mgc-pro. The ethernet module is...

  • Page 8: Notice!

    Ethernet module mgc-pro microdrive installation and network connection 3.1.1 corrective action malfunction possible cause corrective action green led at the centre is not permanently lit. The ethernet module is only supported by the control units mgc- pro. Check label or type sign of the control uni...

  • Page 9

    Ethernet module mgc-pro microdrive installation and network connection 5815,0001en / version 00 11 3.4 menu "ethernet" of the control unit mgc-pro once the ethernet module is plugged in and the control unit supplied with power, the menu "ethernet" appears in the main menu. The position of the menu "...

  • Page 10

    Ethernet module mgc-pro microdrive operation via web interface 4 operation via web interface 4.1 web interface you can request the conditions of the barrier and operate the barrier via the web interface. The connection is established in the web browser by entering the ip address. You may have the ip...

  • Page 11

    Ethernet module mgc-pro microdrive operation via web interface barrier operation (not operational) fig. 2: web surface – operation of the barrier (not operational) barrier settings fig. 3: web interface – barrier settings 5815,0001en / version 00 13.

  • Page 12

    Ethernet module mgc-pro microdrive operation via web interface conditions of the in-/outputs fig. 4: web surface – conditions of the in-/outputs loop overview fig. 5: web interface – loop overview 14 5815,0001en / version 00

  • Page 13

    Ethernet module mgc-pro microdrive operation via web interface network configuration fig. 6: web interface – network configuration messages (reboot) fig. 7: web interface – messages (reboot) 5815,0001en / version 00 15.

  • Page 14: 5 Tcp/ip

    Ethernet module mgc-pro microdrive tcp/ip interface 5 tcp/ip interface 5.1 modbus in addition to operation of the barrier via the web interface, communication is possible via the ethernet field bus as modbus tcp as well. Port 502 is used for modbus. After the connection between the client (master) a...

  • Page 15

    Ethernet module mgc-pro microdrive tcp/ip interface 5815,0001en / version 00 17 5.1.2 address table the following modbus address table permits access to the most important functions and conditions of the barrier. For this, the "function codes" 0x3 to 0x6 are used. See page 6, chapter 1.3 "reference ...

  • Page 16

    Ethernet module mgc-pro microdrive tcp/ip interface 18 5815,0001en / version 00 5.1.3 examples reading status – request description value 12 transaction id 34 00 protocol id 00 00 length (number of following bytes) 06 mbap unit id ff function code (read holding register) 03 00 starting address 01 00...

  • Page 17

    Ethernet module mgc-pro microdrive tcp/ip interface 5815,0001en / version 00 19 closing barrier – request description value 12 transaction id 34 00 protocol id 00 00 length (number of following bytes) 06 mbap unit id ff function code (write single register) 06 00 register address 00 00 pdu register ...

  • Page 18

    Ethernet module mgc-pro microdrive tcp/ip interface 20 5815,0001en / version 00 opening barrier – request description value 12 transaction id 34 00 protocol id 00 00 length (number of following bytes) 06 mbap unit id ff function code (write single register) 06 00 register address 00 00 pdu register ...

  • Page 19

    Ethernet module mgc-pro microdrive tcp/ip interface 5.2.2 module addresses the mgc-pro control unit is modularly built. Every plug-in module has a unique basic address. The module address is the sum of the basic address and slot number. This enables operation of several equal plug-in modules like tw...

  • Page 20

    Ethernet module mgc-pro microdrive tcp/ip interface 22 5815,0001en / version 00 5.2.4 examples reading cycle counter – request description value 12 transaction id 34 00 protocol id 00 00 length (number of following bytes) 0e mbap unit id ff function code 2b mei type 0d protocol control 02 reserved f...

  • Page 21

    Ethernet module mgc-pro microdrive tcp/ip interface 5815,0001en / version 00 23 setting programme mode – request description value 12 transaction id 34 00 protocol id 00 00 length (number of following bytes) 0f mbap unit id ff function code 2b mei type 0d protocol control 03 reserved field 00 protoc...

  • Page 22

    Ethernet module mgc-pro microdrive tcp/ip interface 24 5815,0001en / version 00 reading device name module 1 – request description value 12 transaction id 34 00 protocol id 00 00 length (number of following bytes) 0e mbap unit id ff function code 2b mei type 0d protocol control 02 reserved field 00 ...

  • Page 23: 6 Commissioning

    Ethernet module mgc-pro microdrive commissioning 5815,0001en / version 00 25 6 commissioning 6.1 procedure we recommend the following procedure for initial commissioning: 1. Taking control unit into operation without network cable. 2. Check dhcp settings. 3. Switch off control unit. 4. Connect netwo...

  • Page 24: 7 Appendix

    Ethernet module mgc-pro microdrive appendix 26 5815,0001en / version 00 7 appendix the description of the status words and object tables are available in document 5815,0000 "microdrive mgc/mgc-pro additional information for system integrators". 8 list of abbreviations abbreviatio n meaning descripti...

  • Page 25: Index

    Ethernet module mgc-pro microdrive index 5815,0001en / version 00 27 index a address table......................................................17 adu ....................................................................16 c cable type ............................................................8 can...

  • Page 26

    Web: www.Magneticgateopeners.Com phone: (800) 878-7829 fax: (330) 650-9004 email: sales@magneticgateopeners.Com.