- DL manuals
- Magnetic Autocontrol
- Gate Opener
- MHTM MicroDrive
- Operating Instructions Manual
Magnetic Autocontrol MHTM MicroDrive Operating Instructions Manual - 6.3
Barrier MHTM
TM
MicroDrive
Transport and storage
5815,5001US / Version 02.66
49
6.3
Transport
Barrier housing and barrier arm are delivered separately.
The lifting gear must be designed for the weight of the barrier
housing and barrier arm.
For transport barrier modules refer to the safety notes on page 47,
chapter 6.1.
For future transports:
Secure loose cables.
Secure against vibrations.
Securely fasten the barrier housing and barrier arm prior to
transport (e.g. screw it onto a pallet).
Transport and put down barrier housing and barrier arm with a
forklift and lift with suitable lifting gear.
6.4
Storage
Store the barrier or packages under the following conditions:
Do not store outdoors.
Store dry and dust free.
Do not expose to aggressive media.
Protect against solar irradiation.
Avoid mechanical vibrations.
Storage temperature: –22 to +158 °F (–30 to +70 °C)
Relative humidity: max. 95 %, non-condensing
Check the general condition of all components and packaging
regularly, if they are stored for longer periods than 3 months.
Summary of MHTM MicroDrive
Page 1
Operating instructions barrier mhtm tm microdrive doc-id: 5815,5001us version: 02.6.
Page 2
2 5815,5001us / version 02.66 magnetic automation corporation 3160 murrell road rockledge, florida, 32955 usa tel.: +1 321 635 8585 fax.: +1 321 635 9449 e-mail: info@ac-magnetic.Com internet: www.Ac-magnetic.Com.
Page 3
Barrier mhtm tm microdrive important safety instructions 5815,5001us / version 02.66 3 important safety instructions read and follow all instructions. Never let children operate or play with barrier controls. Keep the remote control (where provided) away from children. Personnel should keep away fro...
Page 4
Barrier mhtm tm microdrive 4 5815,5001us / version 02.66.
Page 5: Contents
Barrier mhtm tm microdrive contents 5815,5001us / version 02.66 5 contents 1 general..................................................................................11 1.1 information regarding the operating instructions .........11 1.2 pictogram explanation ...........................................
Page 6
Barrier mhtm tm microdrive contents 6 5815,5001us / version 02.66 4.3 parking ........................................................................ 37 4.3.1 dimensions and weight ............................... 37 4.3.2 electrical connection.................................... 38 4.3.3 operating ...
Page 7
Barrier mhtm tm microdrive contents 5815,5001us / version 02.66 7 8.6 assemble housing .......................................................66 8.7 assemble light barrier post ..........................................68 8.8 assemble safety light barrier .......................................69 8....
Page 8
Barrier mhtm tm microdrive contents 8 5815,5001us / version 02.66 10.5 parameterising options ............................................. 110 10.6 parameterising values............................................... 111 10.7 select program mode................................................ 112 1...
Page 9
Barrier mhtm tm microdrive contents 5815,5001us / version 02.66 9 11 start-up and operation ......................................................151 11.1 safety ....................................................................151 11.2 commissioning ..................................................
Page 10
Barrier mhtm tm microdrive 10 5815,5001us / version 02.66.
Page 11: 1 General
Barrier mhtm tm microdrive general 5815,5001us / version 02.66 11 1 general 1.1 information regarding the operating instructions these operating instructions provide crucial information on handling of magnetic barriers mhtm tm microdrive. Pre-requisite for safe working is the observance of all speci...
Page 12: 1.2
Barrier mhtm tm microdrive general 12 5815,5001us / version 02.66 1.2 pictogram explanation warning notes warning notes are characterised by pictograms in these operating instructions. The warning notes are followed by signal words expressing the scale of the hazard. It is absolutely essential to ob...
Page 13: 1.3
Barrier mhtm tm microdrive general 5815,5001us / version 02.66 13 1.3 limitation of liability all specifications and notes in these operating instructions were compiled with consideration to the valid standards and regulations, the state of the art as well as to our long-standing knowledge and exper...
Page 14: 1.5
Barrier mhtm tm microdrive general 14 5815,5001us / version 02.66 1.5 scope of delivery the scope of delivery comprises: 1 barrier housing incl. Drive unit and control 1 barrier 2 mounting profiles 2 warning signs edge protection options if applicable supplied documentation per barrier: these operat...
Page 15: 1.9
Barrier mhtm tm microdrive general 5815,5001us / version 02.66 15 1.9 environmental protection notice! Notice! Danger for the environment by improper disposal of components or the barrier! In case of improper disposal of components or the barrier, damage to the environment may result. Therefore: – o...
Page 16: 2 Safety
Barrier mhtm tm microdrive safety 16 5815,5001us / version 02.66 2 safety 2.1 intended use of the barriers the magnetic mhtm tm microdrive barrier is intended for installation only on passageway used for vehicles. Pedestrians must be supplied with a separate access opening. The pedestrian access ope...
Page 17: Warning!
Barrier mhtm tm microdrive safety 5815,5001us / version 02.66 17 2.1.2 non-intended use control of pedestrian traffic as contrary to intended use. The barriers must not be used at railway crossings. The barriers are not approved for pedestrian traffic, bicycles or animals. The barriers must not be u...
Page 18: 2.2
Barrier mhtm tm microdrive safety 18 5815,5001us / version 02.66 2.2 operator's responsibility the operator must comply with the statutory obligations regarding work safety. In addition to the work safety notes in these operating instructions, the safety, accident prevention and environmental provis...
Page 19: 2.4
Barrier mhtm tm microdrive safety 5815,5001us / version 02.66 19 2.4 specialists and operating personnel 2.4.1 requirements warning! Warning! Risk of injury in case of inadequate qualification! Improper handling can lead to considerable bodily injuries and property damage. Therefore: – have any acti...
Page 20: 2.5
Barrier mhtm tm microdrive safety 20 5815,5001us / version 02.66 2.5 personal protective equipment it is necessary to wear personal protective equipment when dealing with the barrier so as to minimise health hazards. Before carrying out any work, properly dress in the necessary protective equipment ...
Page 21: Caution!
Barrier mhtm tm microdrive safety 5815,5001us / version 02.66 21 hot surfaces caution! Caution! Danger of burns! … indicates the presence of a hot surface. Non- observance of the safety instructions can lead to minor injuries. This pictogram is fixed on the following component: – motor in the barrie...
Page 22: Danger!
Barrier mhtm tm microdrive safety 22 5815,5001us / version 02.66 electric voltage – missing protective facilities danger! Danger! Mortal danger by electric voltage! The safety installations that are required according to regional and local regulations must be provided by the customer. Usually these ...
Page 23: Warning!
Barrier mhtm tm microdrive safety 5815,5001us / version 02.66 23 improper operation warning! Warning! Danger from improper operation of the barrier! Improper operation of the barrier can cause severe or lethal injuries! Therefore: – the barrier closes automatically in certain program modes. Passing ...
Page 24: Warning!
Barrier mhtm tm microdrive safety 24 5815,5001us / version 02.66 entering the danger area of the barrier warning! Warning! Danger from entering the danger area! The magnetic mhtm tm microdrive barriers are intended exclusively for closing off passages for motor vehicles and trucks. For vehicles that...
Page 25: Warning!
Barrier mhtm tm microdrive safety 5815,5001us / version 02.66 25 improper transport warning! Warning! Danger from improper transport of the barrier arm and housing! The weight of the barrier arm or housing can severely injure a person! Therefore: – have them transported by specialists only. – use li...
Page 26: Warning!
Barrier mhtm tm microdrive safety 26 5815,5001us / version 02.66 insufficient fixing warning! Warning! Risk of injury at insufficient fixing! Insufficient fixing of individual components such as barrier housing, barrier arm and additions permitted by the manufacturer can cause severe injury! Therefo...
Page 27: Caution!
Barrier mhtm tm microdrive safety 5815,5001us / version 02.66 27 illegible signage caution! Caution! Risk of injury by illegible symbols! Labels and signs can become dirty or unrecognisable in the course of time. Therefore: – always keep safety, warning and operating notes in a well readable conditi...
Page 28: 2.7
Barrier mhtm tm microdrive safety 28 5815,5001us / version 02.66 2.7 danger area danger of crushing and shearing, barrier arm warning! Warning! Danger of crushing and shearing when the barrier opens or closes! When a barrier opens or closes, the barrier arm may lead to severe crushing or injury! The...
Page 29: 3 Identification
Barrier mhtm tm microdrive identification 5815,5001us / version 02.66 29 3 identification 3.1 type plate the type plate is provided inside at the barrier housing, next to the hood attachment. 8 3 4 7 9 2 1 q s-nr. Made in germany 10 mag00168b 6 magnetic autocontrol gmbh d-79650 schopfheim 5 fig. 2: ...
Page 30: 3.2
Barrier mhtm tm microdrive identification 30 5815,5001us / version 02.66 3.2 type code – r a 0 3 0 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 position description 1 – 13 product group: access magnetic.Acess access-l magnetic.Access lang access pro magnetic.Access pro access pro-l magn...
Page 31: 4 Technical
Barrier mhtm tm microdrive technical data 5815,5001us / version 02.66 31 4 technical data 4.1 access 4.1.1 dimensions and weight mag00109c a b 1 varioboom 2 1 2.17 (55) 3.94 (100) min. 2 ft (min. 610) 12 ft (3660) / 14 ft (4300) / 20 ft (6000) 14.2 (360) 36.4 (925) 36.0 (915) 34.5 (875) min. 31.5 (8...
Page 32
Barrier mhtm tm microdrive technical data 32 5815,5001us / version 02.66 designation unit access access pro access select l l l line width ft (m) 12 (3.66) 15 (4.57) 12 (3.66) 20 (6.10) 12 (3.66) 20 (6.10) barrier housing (width x depth x height) in (mm) see page 31, fig. 3. 12.4 x 13.6 x 36.0 (315 ...
Page 33
Barrier mhtm tm microdrive technical data 5815,5001us / version 02.66 33 4.1.4 operating times designation unit access access pro access select l l l opening time/ closing time s 2.2 4.0 1.3 4.0 1.3 4.0 table 5: operating times – "access" series.
Page 34: 4.2
Barrier mhtm tm microdrive technical data 34 5815,5001us / version 02.66 4.2 access pro h 4.2.1 dimensions and weight mag00202a a b microboom 2 1 1 43.90 (1 1 15) min. 2 ft (min. 610) min. 2 ft (min. 610) 36.4 (925) 34.5 (875) 12 ft (3660) / 14 ft (4300) / 20 ft (6000) min. 31.5 (800) 14.2 (360) 12....
Page 35
Barrier mhtm tm microdrive technical data 5815,5001us / version 02.66 35 designation unit access pro h ft (m) 12 (3.66) 15 (4.57) 20 (6.00) line width ft (m) 12 (3.66) 15 (4.57) 20 (6.00) barrier housing (width x depth x height) in (mm) see page 34, fig. 4. 12.4 x 13.6 x 36.0 (315 x 360 x 915) weigh...
Page 36
Barrier mhtm tm microdrive technical data 36 5815,5001us / version 02.66 4.2.4 operating times designation unit access pro h ft (m) 12 (3.66) 14 (4.3) 20 (6.00) opening time/ closing time s 4.0 4.0 4.0 table 9: operating times – "access pro h".
Page 37: 4.3
Barrier mhtm tm microdrive technical data 5815,5001us / version 02.66 37 4.3 parking 4.3.1 dimensions and weight mag00198a a b 1 varioboom 2 1 2.17 (55) 3.94 (100) min. 2 ft (min. 610) 12 ft (3660) 14.2 (360) 36.4 (925) 36.0 (915) 34.5 (875) min. 31.5 (800) 9.65 (245) 12.4 (315) 3.82 (97) 26.6 (675)...
Page 38
Barrier mhtm tm microdrive technical data 38 5815,5001us / version 02.66 designation unit parking parking pro parking select line width ft (m) 12 (3.66) 12 (3.66) 12 (3.66) barrier housing (width x depth x height) in (mm) see page 37, fig. 5. 12.4 x 13.6 x 36.0 (315 x 360 x 915) weight barrier housi...
Page 39: 4.4
Barrier mhtm tm microdrive technical data 5815,5001us / version 02.66 39 4.4 toll 4.4.1 dimensions and weight microboom-t mag00108b 2 1 a b 1 10 ft (3000) min. 31.5 (800) 2.95 (75) min. 2 ft (min. 610) 8.86 (255) 36.4 (910) 43.9 (1 1 15) 34.4 (875) 3.82 (97) min. 2 ft (min. 610) 14.2 (360) 12.4 (315...
Page 40
Barrier mhtm tm microdrive technical data 40 5815,5001us / version 02.66 designation unit toll toll pro line width ft (m) 10 (3) barrier housing (width x depth x height) in (mm) see page 43, fig. 7. 12.4 x 14.7 x 43.9 (315 x 360 x 1115) weight barrier housing lbs (kg) 92.6 (42) table 14: dimensions ...
Page 41: 4.5
Barrier mhtm tm microdrive technical data 5815,5001us / version 02.66 41 4.5 control unit designation unit mgc (magnetic gate controller) supply voltage v dc 24 current consumption ─ max. 1 a, max. 300 ma + current consumption of the different plug-in modules power consumption ─ max 24 w, max. 7.2 w...
Page 42: 4.6
Barrier mhtm tm microdrive technical data 42 5815,5001us / version 02.66 4.6 plug-in module "detector a–b" designation unit plug-in module "detector a–b" current consumption ma 50 number of loop detectors ─ 2 (a and b) inductance range h 70 to 500 number of induction loop sensitivity levels ─ 10 lev...
Page 43: 5 Design and Function
Barrier mhtm tm microdrive design and function 5815,5001us / version 02.66 43 5 design and function 5.1 design 5.1.1 access and parking mag00199 2 1 4 5 3 fig. 7: barrier system design series "access" and series "parking" 1 barrier housing 2 varioboom (barrier arm) 3 pendulum support from 15 ft (4.5...
Page 44
Barrier mhtm tm microdrive design and function 44 5815,5001us / version 02.66 5.1.2 access pro h mag00203 2 1 4 5 3 fig. 8: design barrier series "access pro h" 1 barrier housing 2 microboom access pro h 3 pendulum support from 15 ft (4.57 m) barrier arm length 4 empty conduits for mains cable, cont...
Page 45
Barrier mhtm tm microdrive design and function 5815,5001us / version 02.66 45 5.1.3 toll mag00200 2 3 4 1 fig. 9: design barrier system series "toll" 1 barrier housing 2 "microboom-t" barrier arm 3 empty conduits for mains cable, control lines and induction loop 4 concrete foundation with reinforcem...
Page 46: 5.2
Barrier mhtm tm microdrive design and function 46 5815,5001us / version 02.66 5.2 function the barrier consists of a barrier housing with drive system and a barrier arm. The drive system consists of an electric motor, control unit, and the lever system. The lever system locks the barrier arm in both...
Page 47: 6 Transport and Storage
Barrier mhtm tm microdrive transport and storage 5815,5001us / version 02.66 47 6 transport and storage 6.1 safety improper transport warning! Warning! Danger from improper transport of the barrier arm and housing! The weight of the barrier arm or housing can severely injure a person! Therefore: – h...
Page 48: Notice!
Barrier mhtm tm microdrive transport and storage 48 5815,5001us / version 02.66 improper transport notice! Notice! The barrier system can be damaged by improper transport! Substantial material damages can result from improper transport. Therefore: – have all transport work performed by trained perso...
Page 49: 6.3
Barrier mhtm tm microdrive transport and storage 5815,5001us / version 02.66 49 6.3 transport barrier housing and barrier arm are delivered separately. The lifting gear must be designed for the weight of the barrier housing and barrier arm. For transport barrier modules refer to the safety notes on ...
Page 50
Barrier mhtm tm microdrive design notes for induction loops 50 5815,5001us / version 02.66 7 design notes for induction loops for assembly and inspection, see page 61, chapter 8.4. Please observe following points when dimensioning the induction loops: induction loops respond only to metal. The mass ...
Page 51
Barrier mhtm tm microdrive design notes for induction loops 5815,5001us / version 02.66 51 arrangement passenger car loops – passage with long opening loop mag00074 1 2 3 fig. 11: passenger car loops – passage with long opening time 1 safety loop 2 opening loop 3 barrier due to a long opening loop v...
Page 52
Barrier mhtm tm microdrive design notes for induction loops 52 5815,5001us / version 02.66 arrangement of truck/ passenger car loops mag00076 2 3 4 1 ca. 3.28 ft (1.00 m) ca. 4.92 ft (1.50 m) ca. 3.28 ft (1.00 m) 3.28 ft (1.00 m) ca. 3.28 ft (1.00 m) ca. 4.92 ft (1.50 m) ca. 3.28 ft (1.00 m) 3.28 ft...
Page 53: 8 Assembly
Barrier mhtm tm microdrive assembly and installation 5815,5001us / version 02.66 53 8 assembly and installation 8.1 safety see also safety notes on page 20, chapter 2.6 "occupational safety and special dangers". Non-intended use warning! Warning! Non-intended use is dangerous! Any use of the barrier...
Page 54: Warning!
Barrier mhtm tm microdrive assembly and installation 54 5815,5001us / version 02.66 general warning! Warning! Danger by inappropriate installation! Inappropriate installation can cause severe injuries! Therefore: – only specialist personnel or electrical specialists must perform any assembly and ins...
Page 55: 8.2
Barrier mhtm tm microdrive assembly and installation 5815,5001us / version 02.66 55 8.2 required steps the following steps are to be completed prior to assembly and installation: laying the foundation with reinforcement for the barrier and install empty conduits. Set up foundation for light barrier ...
Page 56: 8.3
Barrier mhtm tm microdrive assembly and installation 56 5815,5001us / version 02.66 8.3 foundation and empty conduits mag00227 1 2 4 3 1 5 6 11.81 (300) min. 2 ft (min. 610) min. 31.5 (800) 3.94 (100) 23.6 (600) min. 2 ft (min. 610) min. 31.5 (800) fig. 14: assembly boom system dimensions in inch or...
Page 57
Barrier mhtm tm microdrive assembly and installation 5815,5001us / version 02.66 57 8.3.1 foundation and empty conduits for the barrier assembly site the assembly site must meet the following requirements: the barrier must be visible from the operating person. The barrier must not be put up where th...
Page 58
Barrier mhtm tm microdrive assembly and installation 58 5815,5001us / version 02.66 laying the foundation, installing empty conduits a a 1 2 3 4 5 mag00155 6 7 (135) 5.31 (135) 5.31 (160) 6.30 7.09 6.30 (160) 23.6 (600) 17.7 (450) 19.7 (500) (180) (180) 7.09 min. 31.5 (800) fig. 15: foundation plan ...
Page 59
Barrier mhtm tm microdrive assembly and installation 5815,5001us / version 02.66 59 3. Place empty conduits pursuant to fig. 15 in the foundation hole. 4. Close empty conduits to prevent water from entering. 5. Fill concrete foundation pursuant to fig. 14. 6. Create flat line in the base area. The f...
Page 60
Barrier mhtm tm microdrive assembly and installation 60 5815,5001us / version 02.66 laying the foundation, installing empty conduits 1 3 mag00223 2 11.81 (300) 11.81 (300) x x x x x x 4 min. 31.5 (800) 3.15 (80) 4.33 (1 10) x = 3.94 (100) fig. 17: foundation plan for light barrier post dimensions in...
Page 61: 8.4
Barrier mhtm tm microdrive assembly and installation 5815,5001us / version 02.66 61 8.4 assembly and installation of induction loops depending on the application safety installations must be installed on site. Induction loops, light barriers, etc. Can be used as safety installations. The safety inst...
Page 62
Barrier mhtm tm microdrive assembly and installation 62 5815,5001us / version 02.66 please observe following points when installing the induction loop: loop geometry and clearances install the loop symmetrically to the barrier arm. Please make sure that the barrier arm is attached to the side of the...
Page 63
Barrier mhtm tm microdrive assembly and installation 5815,5001us / version 02.66 63 8.4.2 induction loops the induction loops are available as ready assembled cables in various lengths from several manufacturers. Make sure that they meet the specification described in these operating instructions. A...
Page 64
Barrier mhtm tm microdrive assembly and installation 64 5815,5001us / version 02.66 2. Lay the loop carefully into the groove and push it down by means of a blunt object, such as a piece of wood. The insulation must by no means be damaged. 3. To avoid slipping of the loop, fix the loop using small w...
Page 65
Barrier mhtm tm microdrive assembly and installation 5815,5001us / version 02.66 65 8.4.5 installing induction loops under interlocking stone paving s0105a 3 1 4 5 2 11.8 (300) 5.91 (150) 1.18 (30) fig. 21: installing an induction loop under interlocking stone paving dimensions in inch are without p...
Page 66: 8.5
Barrier mhtm tm microdrive assembly and installation 66 5815,5001us / version 02.66 8.5 unpacking the individual packages are packed according to the expected transport conditions. Only environment-friendly materials have been used for the packaging. The packaging should protect the individual compo...
Page 67
Barrier mhtm tm microdrive assembly and installation 5815,5001us / version 02.66 67 1. The foundation must have cured. 8 1 2 5 6 7 4 3 9 mag00205 fig. 22: assemble housing 1 barrier housing 2 nut 3 spring washer 4 washer d8,4 5 washer d13 6 mounting profile 7 foundation anchor 8 foundation 9 silicon...
Page 68: 8.7
Barrier mhtm tm microdrive assembly and installation 68 5815,5001us / version 02.66 8.7 assemble light barrier post the light barrier post is attached with 4 foundation anchors each. Requirements mounting material magnetic automation corporation recommends using 3/8" anchor bolts. Refer to the ancho...
Page 69: 8.8
Barrier mhtm tm microdrive assembly and installation 5815,5001us / version 02.66 69 8.8 assemble safety light barrier only magnetic safety light barriers must be used. 8.8.1 assemble transmitter a b b mag00224 a 4 3 1 2 1 c 6.30 (160) 0.67 (17) 1 1.02 (280) 1 1.50 (292) Ø 0.51 (Ø 13) Ø 24 (Ø 6) Ø 0....
Page 70
Barrier mhtm tm microdrive assembly and installation 70 5815,5001us / version 02.66 8.8.2 assemble receiver 6.30 (160) 12.17 (309) 1.18 (30) x x x mag00225 3 4 5 3 a 1 2 b fig. 24: assemble the receiver's light barrier housing on the post dimensions in inch or feet are without parenthesis. Dimension...
Page 71: 8.9
Barrier mhtm tm microdrive assembly and installation 5815,5001us / version 02.66 71 8.9 assemble barrier arm type "varioboom" the barrier arm type "varioboom" is delivered in two parts. Short barrier arm profile with assembled connection plates, half- shells and end caps. Long barrier arm profile th...
Page 72: Caution!
Barrier mhtm tm microdrive assembly and installation 72 5815,5001us / version 02.66 the edge protection is included in the delivery loosely in 6.56 ft (2 m) pieces. If the barrier was ordered with the light strips option, the barrier arm is delivered with the mounted edge protection. The number of e...
Page 73
Barrier mhtm tm microdrive assembly and installation 5815,5001us / version 02.66 73 warning! Danger of crushing between barrier arm and barrier housing! 4. Switch off power supply. Ensure that the system is powered down. Secure against reactivation. The balancing springs in the lever system are rela...
Page 74
Barrier mhtm tm microdrive assembly and installation 74 5815,5001us / version 02.66 8. Install end cap to the barrier arm. Mag00172a fig. 28: install end cap 9. Push barrier arm with pre-assembled flange onto the flange shaft. Mag00175 fig. 29: assemble flange with barrier arm 10. Align barrier arm ...
Page 75
Barrier mhtm tm microdrive assembly and installation 5815,5001us / version 02.66 75 13. Push the barrier into the top-most position. The clamping lever must be at the stop for the "open" position. If required, push straight through the upper tool bore with a tool to press the lever arm from the dead...
Page 76
Barrier mhtm tm microdrive assembly and installation 76 5815,5001us / version 02.66 5. Install the flange on the flange plates with the 2 hexagon socket screws 8 af. Make sure: tighten the screws evenly with a tightening torque of 44.254 lbf ft (60 nm). That the air gap between flange and flange pla...
Page 77
Barrier mhtm tm microdrive assembly and installation 5815,5001us / version 02.66 77 9. Push the barrier into the top-most position. The clamping lever must be at the stop for the "open" position. If required, push straight through the upper tool bore with a tool to press the lever arm from the dead ...
Page 78: (Varioboom and Microboom)
Barrier mhtm tm microdrive assembly and installation 78 5815,5001us / version 02.66 8.12 conversion "left version" – "right version" (varioboom and microboom) danger of injury caution! Caution! Danger of injury! There is a danger of injury when mounting the barrier arm. Therefore: – barrier arm as o...
Page 79
Barrier mhtm tm microdrive assembly and installation 5815,5001us / version 02.66 79 mag00175 fig. 32: disassemble flange with barrier arm 8. Remove the v-ring from the flange shaft. Mag00174 fig. 33: remove the v-ring 9. Slightly loosen the two hexagon socket screws 10 af of the clamping lever at th...
Page 80
Barrier mhtm tm microdrive assembly and installation 80 5815,5001us / version 02.66 10. Unhook the balancing springs in the lever system. For this, press a tool straight through the upper tool bore. The lever arm is pressed from the upper dead point. See page 168, chapter 13.5. 11. Remove the flange...
Page 81
Barrier mhtm tm microdrive assembly and installation 5815,5001us / version 02.66 81 26. Switch the "service" switch on the control unit. The led lights red. The display backlighting flashes. See page 122, chapter 10.7.7 mode "service". 27. Close the barrier with the middle right button at the contro...
Page 82: Warning!
Barrier mhtm tm microdrive assembly and installation 82 5815,5001us / version 02.66 8.13 check and set the balancing springs in the lever system danger of crushing, lever system warning! Warning! Danger of crushing at opened barrier housing at the lever system! The lever system in the barrier housin...
Page 83
Barrier mhtm tm microdrive assembly and installation 5815,5001us / version 02.66 83 mag00169 1 2 3 fig. 35: balancing springs in the lever system. 1 barrier arm 2 balancing spring 3 screw with locknuts 8.13.1 setting balancing springs check and adjust balancing springs check balancing springs with t...
Page 84
Barrier mhtm tm microdrive assembly and installation 84 5815,5001us / version 02.66 adjust balancing springs: 5. Remove the barrier housing hood. 6. Remove the rear barrier housing door. 7. Adjust springs with a wrench via the screws with locknuts. Barrier arm angle > approx. 30°: this balancing spr...
Page 85
Barrier mhtm tm microdrive assembly and installation 5815,5001us / version 02.66 85 the following overview tables apply for barriers with microboom. Line width number springs weak number springs strong 4.9 to 6.6 ft (1.5 to 2.0 m) 1 – 6.9 to 8.2 ft (2.1 to 2.5 m) 2 – 8.5 to 10.2 ft (2.6 to 3.1 m) 3 ...
Page 86: Warning!
Barrier mhtm tm microdrive assembly and installation 86 5815,5001us / version 02.66 8.14 align barrier housing and light barrier post falling components warning! Warning! Risk of injury from falling components! Falling components such as the barrier housing can cause severe injury! Therefore: – when...
Page 87
Barrier mhtm tm microdrive assembly and installation 5815,5001us / version 02.66 87 8.15 installing warning signs warning signs for the barrier a minimum of two warning signs have be installed, one on each side of the barrier where easily visible. Two warning signs for the barrier are part of delive...
Page 88: 9 Electrical
Barrier mhtm tm microdrive electrical connection 88 5815,5001us / version 02.66 9 electrical connection 9.1 safety see also safety notes on page 20, chapter 2.6 "occupational safety and special dangers". Electric voltage – inadequate qualification danger! Danger! Mortal danger by electric voltage! R...
Page 89: Danger!
Barrier mhtm tm microdrive electrical connection 5815,5001us / version 02.66 89 electric voltage danger! Danger! Mortal danger by electric voltage! Touching live parts can be lethal. Damage to the insulation or to individual compo- nents can be lethal. Therefore: – switch off the power supply immedi...
Page 90: Caution!
Barrier mhtm tm microdrive electrical connection 90 5815,5001us / version 02.66 hot surfaces caution! Caution! Danger of burns! The motor surface may be hot. Touching this hot surface can lead to burns. Therefore: – do not touch these hot surfaces. – after switching off the power supply wait some mi...
Page 91: 9.2
Barrier mhtm tm microdrive electrical connection 5815,5001us / version 02.66 91 9.2 installing electrical protective devices the safety installations that are required according to regional and local regulations must be provided by the customer. Usually these are: ground fault circuit interrupter (g...
Page 92
Barrier mhtm tm microdrive electrical connection 92 5815,5001us / version 02.66 danger! Mortal danger by electric voltage! 1. Disconnect barrier system power supply. Ensure that the system is powered down. Secure against reactivation. Strip-off cable and core insulation – preparation of the wiring 2...
Page 93: 9.4
Barrier mhtm tm microdrive electrical connection 5815,5001us / version 02.66 93 connecting mains supply mag00207 1 2 3 4 fig. 40: connecting the mains supply 1 terminal clamps for mains supply 2 phase l 3 neutral conductor n 4 ground conductor pe 9.4 connect customer's control lines (signalling devi...
Page 94
Barrier mhtm tm microdrive electrical connection 94 5815,5001us / version 02.66 1 2 3 4 5 mag00180 fig. 41: connecting the control lines 1 cable opening rear 2 control unit 3 cable tie metal tabs 4 cable opening front 5 cable clamps 9.4.1 connecting safety devices as safety devices, you must connect...
Page 95
Barrier mhtm tm microdrive electrical connection 5815,5001us / version 02.66 95 note! The input function "safety devices" must only be used for additional safety devices. The input function is not considered for the plausibility check. A safety loop always has to be connected to the detector module ...
Page 96
Barrier mhtm tm microdrive electrical connection 96 5815,5001us / version 02.66 note! If four induction loops must be supervised, you can connect another plug-in module with the "detector" function into the control unit. This plug-in module registers as "detector 2 (c-d)". To prevent mutual interfer...
Page 97: Warning!
Barrier mhtm tm microdrive electrical connection 5815,5001us / version 02.66 97 9.4.6 digital inputs improper parameterisation warning! Warning! Risk of injury by improper parameterisation of the control unit! Improper parameterisation of the control unit can lead to severe injuries! Therefore: – th...
Page 98
Barrier mhtm tm microdrive electrical connection 98 5815,5001us / version 02.66 the functions have different priorities towards each other. The function "open high priority" has the highest priority (priority 1). I.E. All other functions, such as "open low priority", "close", etc. Are ignored if the...
Page 99
Barrier mhtm tm microdrive electrical connection 5815,5001us / version 02.66 99 function description safety device the barrier can no longer be closed when +0 v dc are applied to this input. If the barrier is just closing when the input signal changes to 0 v and the cut off angle has not been underc...
Page 100
Barrier mhtm tm microdrive electrical connection 100 5815,5001us / version 02.66 function description error when the control unit recognizes any "safety-relevant error" or "error", the output with this function is reactivated (fail safe). Warning when the control unit recognizes any "warning", the o...
Page 101
Barrier mhtm tm microdrive electrical connection 5815,5001us / version 02.66 101 function description loop active pulse b when a vehicle drives into loop b (rising flank), the output with this function emits a pulse. Loop inactive pulse a when a vehicle drives out of loop a (falling flank), the outp...
Page 102
Barrier mhtm tm microdrive electrical connection 102 5815,5001us / version 02.66 function description direction 2 pls b => a the vehicle drives from direction b to a. When the vehicle drives on loop b in the direction of loop a, this output emits a counter pulse of 300 ms. A b do no/nc t = 300 ms ma...
Page 103
Barrier mhtm tm microdrive electrical connection 5815,5001us / version 02.66 103 function description direction 2 a => b the vehicle drives from direction a to b. When the vehicle enters loop b, this output starts emitting a continuous signal. When the vehicle leaves loop b, this output stops the pe...
Page 104: 9.5
Barrier mhtm tm microdrive electrical connection 104 5815,5001us / version 02.66 9.5 checking the electrical connection the following points have to be checked after the electrical installation of the barrier: are the following electrical protective devices installed: 2-pole main switch, circuit bre...
Page 105: 10.1 Safety
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 105 10 parameterising control unit 10.1 safety see also safety notes on page 20, chapter 2.6 "occupational safety and special dangers". Improper parameterisation warning! Warning! Risk of injury by improper parameteri...
Page 106
Barrier mhtm tm microdrive parameterising control unit 106 5815,5001us / version 02.66 10.3 displays on the control unit example "operational view" mag00126a a b d c access select 4 4 5 6 1 2 3 fig. 44: example "operational view" 1 program mode, here program mode 4 2 barrier type, here type "access ...
Page 107
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 107 10.4 symbols in the display 10.4.1 control button functions the control unit is equipped with 4 control buttons. The function of the control buttons change depending on the current view in the display. The current...
Page 108
Barrier mhtm tm microdrive parameterising control unit 108 5815,5001us / version 02.66 10.4.2 current state of the barrier the barrier can have the following states: symbols description barrier arm closed. Barrier arm open. Barrier arm opens. Closing signal was recognized. Traffic lights active. Bar...
Page 109
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 109 10.4.3 current program mode symbols description current program mode, here program mode 4 for description of program modes, refer to page 112, chapter 10.7. Program mode "service" for description of program mode "...
Page 110
Barrier mhtm tm microdrive parameterising control unit 110 5815,5001us / version 02.66 10.5 parameterising options menu setup, refer to page 189. Program modes overview, refer to page 112. Example: select program mode 1. The operating view is displayed. See page 106, fig. 44. 2. Press right control ...
Page 111
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 111 10.6 parameterising values example: change hold-open time 1. The operating view is displayed. See page 106, fig. 44. 2. Press right control button . 3. The "main menu" menu is displayed. 4. Select the menu "setup"...
Page 112: 10.7 Select Program Mode
Barrier mhtm tm microdrive parameterising control unit 112 5815,5001us / version 02.66 10.7 select program mode 8 program modes and the service mode are available for the mhtm tm microdrive barriers. Program modes 1 to 4 are manual modes. In the manual modes, the barrier must be closed manually afte...
Page 113
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 113 10.7.1 mode 1: maintained contact typical application this mode is suitable for barriers that are integrated in a superordi- nated system like a plant, e.G. To control access to machines. In this mode, the barrier...
Page 114
Barrier mhtm tm microdrive parameterising control unit 114 5815,5001us / version 02.66 10.7.2 mode 2: deadman typical application this mode is suitable for barriers on parking places, factory premises, etc. The barrier must be operated by a person. Function the barrier is operated by two buttons. Fo...
Page 115
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 115 10.7.3 mode 3: pulse control (bistable) typical application this mode is suitable for barriers on factory premises, etc. That are little frequented by vehicles. The signal generator may be, e.G. A wireless button....
Page 116
Barrier mhtm tm microdrive parameterising control unit 116 5815,5001us / version 02.66 10.7.4 mode 4: two-pulse control (bistable) typical application this mode is suitable for barriers on factory premises, etc. That are often frequented by vehicles. The barrier must be operated by a person. Functio...
Page 117
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 117 10.7.5 automatic modes 5 to 8: drive direction 1 – overview and differences the automatic modes differ in their functions in drive direction 1 "safety loop opening loop". In drive direction 2 "opening loop safety ...
Page 118
Barrier mhtm tm microdrive parameterising control unit 118 5815,5001us / version 02.66 mode 5: automatic (5) typical application this mode is suitable for the automatic operation of a barrier, e.G. With card readers, remote control, coin accepters and induction loops or light barriers. Passage of th...
Page 119
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 119 the barrier closes in the following cases: if the vehicle drives over both loops in direction 1 "safety loop opening loop", the barrier closes as soon as the vehicle leaves the safety loop. The opening loop here d...
Page 120
Barrier mhtm tm microdrive parameterising control unit 120 5815,5001us / version 02.66 function from direction 1 "safety loop opening loop", the barrier is opened by an opening signal at one of the digital opening inputs. Hold-open time is not active in this mode. The barrier closes in the following...
Page 121: Warning!
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 121 10.7.6 automatic modes 5 to 8: drive direction 2 in drive direction 2 "opening loop safety loop", the automatic modes are identical. Closing boom warning! Warning! Danger from closing boom! A closing boom may caus...
Page 122
Barrier mhtm tm microdrive parameterising control unit 122 5815,5001us / version 02.66 10.7.7 mode "service" in the "service" mode, all opening and closing signals are ignored. The functions of safety devices like the safety loop or safety light barrier remain active for security reasons. This means...
Page 123: 10.9 Program Mode
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 123 10.8 menu "information" ( ) call and navigate 1. The operating view is displayed. See page 106, fig. 44. 2. Press left control button . 3. Use the left control button to scroll within the menu. 4. The "information...
Page 124: 10.10 Menu "setup"
Barrier mhtm tm microdrive parameterising control unit 124 5815,5001us / version 02.66 10.10 menu "setup" 10.10.1 barrier speed operating view main menu setup barrier speed parameters description close select the closing speed for the barrier arm. The closing speed can be changed for all barrier typ...
Page 125
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 125 operating view main menu setup delays parameters description close delay the barrier only closes if the set time for the closing delay is over. The timer for closing delay is started with the closing signal. With ...
Page 126
Barrier mhtm tm microdrive parameterising control unit 126 5815,5001us / version 02.66 10.10.3 cut off angle operating view main menu setup cut off angle parameters description safety loop close this parameter serves to ensure that a closed barrier can not be opened without authorisation. Where the ...
Page 127
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 127 10.10.6 vend count operating view main menu setup vend count parameters description reset behaviour use this parameter to set vend count reset behaviour. The function "vend count" is available for program modes 4 ...
Page 128
Barrier mhtm tm microdrive parameterising control unit 128 5815,5001us / version 02.66 drive direction 1: "safety loop opening loop" mag00096 1 2 3 4 5 fig. 49: program mode 5 with vend count, passage in direction 1 1 remote control, card reader, coin accepter, etc. 2 barrier 3 opening loop 4 safety...
Page 129
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 129 drive direction 2: "opening loop safety loop" mag00097 1 2 3 4 5 fig. 50: program mode 5 with pulse storage, passage in direction 2 1 remote control, card reader, coin accepter, etc. 2 barrier 3 opening loop 4 saf...
Page 130
Barrier mhtm tm microdrive parameterising control unit 130 5815,5001us / version 02.66 10.10.7 impact settings operating view main menu setup impact settings parameters description impact response select the barrier arm's impact reaction if the control unit detects an impact. Also see page 126, chap...
Page 131
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 131 10.10.8 start-up behaviour use this menu to select the start-up behaviour of the barrier according to the following events: after switching on voltage supply after return of voltage after reset you can select betw...
Page 132
Barrier mhtm tm microdrive parameterising control unit 132 5815,5001us / version 02.66 operating view main menu settings start-up behaviour (start-up behav.) option description 2 reference run in this option, the barrier initially performs a reference run. This means that the barrier opens completel...
Page 133
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 133 operating view main menu settings start-up behaviour (start-up behav.) option description 4 reference run in this option, the barrier arm stops initially. The barrier will only carry out a reference run after a re...
Page 134
Barrier mhtm tm microdrive parameterising control unit 134 5815,5001us / version 02.66 operating view main menu settings start-up behaviour (start-up behav.) option description 6 reference run in this option, the barrier arm stops initially. Release signal the barrier carries out a reference run aft...
Page 135
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 135 10.10.9 power failure operating view main menu setup power failure parameters description power failure this parameter sets whether the barrier arm opens at power outage or opens or closes depending on the barrier...
Page 136
Barrier mhtm tm microdrive parameterising control unit 136 5815,5001us / version 02.66 10.10.10 closure by light barrier operating view main menu settings closure by light barrier (light barr.) parameters description closure by light barrier use this parameter to select the closing behaviour for bar...
Page 137: 10.11 Menu "attachments"
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 137 10.11 menu "attachments" 10.11.1 signal light the parameters "signal mode a", "signal mode b" and "signal mode c" can be used to parameterise the function for the outputs "signal light a", "signal light b" and "si...
Page 138
Barrier mhtm tm microdrive parameterising control unit 138 5815,5001us / version 02.66 operating view main menu attachments signal light parameters description signal mode a (continued) illumination strip red barrier closed (lower end position): red, permanent light barrier opens: red flashes at 2 h...
Page 139
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 139 operating view main menu attachments signal light parameters description lead time in some application cases, it is required for reasons of safety that a warning signal for the following traffic lights up after be...
Page 140
Barrier mhtm tm microdrive parameterising control unit 140 5815,5001us / version 02.66 10.11.2 boom contact settings the barrier can optionally be equipped with a boom contact in the flange. In the "toll" series, the boom contact is integrated by default and performed as a "swing away" or "auto swin...
Page 141: 10.12 Menu "service"
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 141 operating view main menu attachments boom contact settings parameters description closing delay the parameters are only relevant in the following cases: the barrier is a "swing away" or "auto swing away" design. I...
Page 142: 10.13 Menu "information"
Barrier mhtm tm microdrive parameterising control unit 142 5815,5001us / version 02.66 10.13 menu "information" operating view main menu information parameters description serial no. Displays the serial number of the control unit hardware version displays the present hardware version software # disp...
Page 143
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 143 10.15 menu "detector 1 (a-b)" this menu is used to reference the induction loops a and b. Operating view main menu detector 1 (a-b) parameters description recalibration start reference of the induction loops (acti...
Page 144
Barrier mhtm tm microdrive parameterising control unit 144 5815,5001us / version 02.66 operating view main menu setup detector 1 (a-b) frequency settings parameters description freq. A displays the currently measured frequency for induction loop a freq. B displays the currently measured frequency fo...
Page 145
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 145 10.15.2 reconciling and setting the operating frequency of the induction loop operating frequency requirements the operating frequency must fulfil following requirements: when driving over the induction loop with ...
Page 146
Barrier mhtm tm microdrive parameterising control unit 146 5815,5001us / version 02.66 frequency value of the un-assigned induction loop unstable if the frequency value of an induction loop is unstable, this induction loop is influenced by an induction loop of another barrier or an external detector...
Page 147
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 147 10.16 menu "detector 2 (c-d)" this menu is displayed if a second plug-in module with the function "detector" was plugged into the control unit. This menu is used to reference the induction loops c and d. The menu ...
Page 148
Barrier mhtm tm microdrive parameterising control unit 148 5815,5001us / version 02.66 set hand transmitter code the hand transmitter code is set via dip switches in the hand transmitter. We recommend changing the dip switches' standard settings. 1. Open hand transmitter housing. For this, press the...
Page 149
Barrier mhtm tm microdrive parameterising control unit 5815,5001us / version 02.66 149 delete remote control 1. The operating view is displayed. See page 106, fig. 44. 2. Press right operating button . 3. The "main menu" menu is displayed. 4. Select the menu "radio control fm" with the two middle bu...
Page 150: 10.18 Factory Settings
Barrier mhtm tm microdrive parameterising control unit 150 5815,5001us / version 02.66 10.18 factory settings reset parameters this menu can be used to reset the parameters to factory settings. 1. The operating view is displayed. See page 106, fig. 44 2. Press right operating button . 3. The "main m...
Page 151: 11 Start-Up and Operation
Barrier mhtm tm microdrive start-up and operation 5815,5001us / version 02.66 151 11 start-up and operation 11.1 safety see also safety notes on page 20, chapter 2.6 "occupational safety and special dangers". General warning! Warning! Danger by inappropriate start-up and operation! Inappropriate sta...
Page 152: 11.2 Commissioning
Barrier mhtm tm microdrive start-up and operation 152 5815,5001us / version 02.66 11.2 commissioning check before to initial start-up the following inspections must be performed prior to initial start-up: check electrical connections. Check barrier arm position. Check balancing springs in the lever ...
Page 153
Barrier mhtm tm microdrive start-up and operation 5815,5001us / version 02.66 153 switching on 1. Remove the barrier housing hood. 2. Remove the barrier housing door. 3. Switch on the barrier via the double pole mains switch. 4. Depending on the settings in the "start-up behaviour" menu, the barrier...
Page 154: Warning!
Barrier mhtm tm microdrive start-up and operation 154 5815,5001us / version 02.66 11.4 putting the barrier temporarily out of operation high wind speeds warning! Warning! Risk of injury from barrier arm in case of high wind speeds! The barrier arm is no longer securely locked with the mains voltage ...
Page 155: 12 Maintenance
Barrier mhtm tm microdrive maintenance 5815,5001us / version 02.66 155 12 maintenance 12.1 safety see also safety notes on page 20, chapter 2.6 "occupational safety and special dangers". General warning! Warning! Danger by inappropriate maintenance! Inappropriate start-up and operation can cause sev...
Page 156: 12.2 Cleaning
Barrier mhtm tm microdrive maintenance 156 5815,5001us / version 02.66 12.2 cleaning the cleaning interval essentially depends on the environmental conditions and the climate. Aggressive cleaning aids and substances notice! Notice! Unit damage possible! Aggressive detergents and consumables may dama...
Page 157: 12.3 Maintenance Schedule
Barrier mhtm tm microdrive maintenance 5815,5001us / version 02.66 157 12.3 maintenance schedule the following describes the maintenance work that is necessary for optimal, trouble-free operation. Maintenance intervals must be observed. If increased wear of individual components or functional groups...
Page 158
Barrier mhtm tm microdrive maintenance 158 5815,5001us / version 02.66 interval maintenance work to be carried out by check the barrier's mechanics. Check the spring setting of the lever system. Check barrier arm position. Visual inspection of the induction loops and the roadway for damage. Check th...
Page 159: 13 Malfunctions
Barrier mhtm tm microdrive malfunctions 5815,5001us / version 02.66 159 13 malfunctions this chapter describes possible causes of malfunctions and trouble shooting tasks. Contact your dealer in case of malfunctions that cannot be repaired by means of the following information. Procure spare parts fr...
Page 160: Warning!
Barrier mhtm tm microdrive malfunctions 160 5815,5001us / version 02.66 danger of injury after lightning strike warning! Warning! Danger of injury from total outage or barrier malfunction after lightning has hit the barrier! If the barrier is struck by lightening, this may lead to total outage or ma...
Page 161
Barrier mhtm tm microdrive malfunctions 5815,5001us / version 02.66 161 malfunction possible cause corrective action to be carried out by barrier does not open completely. Spring tension in the balancing springs of the lever system set too weakly for the barrier arm weight. Adjust balancing springs....
Page 162
Barrier mhtm tm microdrive malfunctions 162 5815,5001us / version 02.66 malfunction possible cause corrective action to be carried out by barrier does not close. The message "waiting for authorization" appears on the display. The message appears after the voltage supply is switched on, after voltage...
Page 163
Barrier mhtm tm microdrive malfunctions 5815,5001us / version 02.66 163 13.3 warning and interference messages on the display the control unit display indicates the corresponding warning or error message in case of an error. Warning messages warning messages serve as notice. The barrier continues to...
Page 164
Barrier mhtm tm microdrive malfunctions 164 5815,5001us / version 02.66 number description possible cause corrective action ff05 warning book contact / swing-sway active at the "boom contact" input, boom ejection was detected. Barrier with swingaway and automatic return: wait for delay. Barrier with...
Page 165
Barrier mhtm tm microdrive malfunctions 5815,5001us / version 02.66 165 13.3.2 warning and interference messages – motor gw number description possible cause corrective action 2220 warning overcurrent overcurrent was recognised warning may appear in connection with impact. If no impact took place, c...
Page 166
Barrier mhtm tm microdrive malfunctions 166 5815,5001us / version 02.66 number description possible cause corrective action ff37 error motor update failed an error occurred when updating the software perform reset. See page 167, chapter 13.4. Contact service if required. Ff3a warning motor update wa...
Page 167: 13.4 Reset The Barrier
Barrier mhtm tm microdrive malfunctions 5815,5001us / version 02.66 167 13.3.4 warning and interference messages – all modules number description possible cause corrective action 6010 warning watchdog reset sw error contact service if required. 8110 warning bus fault warning contact service if requi...
Page 168
Barrier mhtm tm microdrive malfunctions 168 5815,5001us / version 02.66 13.5 closing or opening the barrier arm in case of power failure in case of power failure, the barrier arm may be in the lower or upper dead point. I.E. The barrier arm can no longer be easily moved manually. In this case, proce...
Page 169: 14 Repair
Barrier mhtm tm microdrive repair 5815,5001us / version 02.66 169 14 repair 14.1 safety see also safety notes on page 20, chapter 2.6 "occupational safety and special dangers". General warning! Warning! Danger by inappropriate repair! Inappropriate repair can cause severe or lethal injuries. Therefo...
Page 170: 14.2 Spare Parts
Barrier mhtm tm microdrive repair 170 5815,5001us / version 02.66 14.2 spare parts warning! Warning! Risk of injury by incorrect spare parts! Incorrect or defective spare parts can result in damage, malfunctions or total failure and also impair safety. Therefore: – use only the manufacturer's origin...
Page 171
Barrier mhtm tm microdrive repair 5815,5001us / version 02.66 171 1. Secure barrier danger area e.G. With barrier tape. 2. Remove the barrier housing hood. 3. Remove the barrier housing door. Warning! Danger of crushing between barrier arm and barrier housing! 4. Switch off power supply. Ensure that...
Page 172
Barrier mhtm tm microdrive repair 172 5815,5001us / version 02.66 10. Remove end cap from the barrier arm. Mag00170 fig. 57: disassemble end cap 11. Slide a slot nut into the groove at the underside of the barrier arm. Place a slot nut on the upper side of the barrier arm. Mag00171 fig. 58: assemble...
Page 173
Barrier mhtm tm microdrive repair 5815,5001us / version 02.66 173 13. Install end cap to the barrier arm. Mag00172a fig. 60: install end cap 14. Push barrier arm with pre-assembled flange onto the flange shaft. 15. Align barrier arm vertically. 16. Install the flange on the flange shaft using the 4 ...
Page 174
Barrier mhtm tm microdrive repair 174 5815,5001us / version 02.66 14.3.2 barrier arm type "microboom-t" 1. Secure barrier danger area e.G. With barrier tape. 2. Remove the barrier housing hood. 3. Remove the barrier housing door. Warning! Danger of crushing between barrier arm and barrier housing! 4...
Page 175
Barrier mhtm tm microdrive repair 5815,5001us / version 02.66 175 11. Switch on power supply. 12. Switch the "service" switch on the control unit. The led lights red. The display backlighting flashes. See page 122, chapter 10.7.7 mode "service". 13. Close the barrier with the middle right button at ...
Page 176
Barrier mhtm tm microdrive decommissioning, disassembly and disposal 176 5815,5001us / version 02.66 15 decommissioning, disassembly and disposal a barrier that is no longer usable should not be recycled as a complete unit, but disassembled into individual components and recycled according to materi...
Page 177
Door, drapery, gate, louver and window operators and systems certified for canada for commercial and industrial use , gate operators, models ls130-01, -10, -11, -41, mib20, mib30, mib35, mib40, mse3, msv3, msv4, msv5, followed by x-yyy, where "x" is r or l and "yyy" is any number 000 thru 999, mts-8...
Page 178
Barrier mhtm tm microdrive 178 5815,5001us / version 02.66.
Page 180
Barrier mhtm tm microdrive 180 5815,5001us / version 02.66.
Page 181: 18 Appendix
Barrier mhtm tm microdrive appendix 5815,5001us / version 02.66 181 18 appendix 18.1 wiring diagrams following wiring diagrams apply to standard barriers. Observe the customer specific wire diagrams for customer specific barriers if applicable..
Page 182
Barrier mhtm tm microdrive appendix 182 5815,5001us / version 02.66.
Page 183
P a g e of m ic ro d ri v e ( u l ) u s a - s ta n d a rd 5 5 2 6 ,0 0 1 2 mhtm 0 0 5 k 1 1 5 0 2 + 4 2 = 1 2 3 4 5 6 7 8 9 3 m a in c o n n e ct io n p o w e r su p p ly u n it 0 1 0 1 1 1 .1 0 .1 1 5 k 1 1 5 5 4 g p 0 2 0 8 .1 1 .1 1 5 k 1 1 5 6 0 g p 1 1 .0 2 .2 0 1 1 gp d a te n a m e m o d if i...
Page 185
P a g e of m ic ro d ri v e ( u l ) u s a - s ta n d a rd 5 5 2 6 ,0 0 1 2 mhtm 0 0 5 k 1 1 5 0 2 + 4 3 = 1 2 3 4 5 6 7 8 9 4 b a rr ie r co n tr o lle r m g c in p u t/ o u tp u t 0 2 0 1 1 1 .1 0 .1 1 5 k 1 1 5 5 4 g p 0 2 0 8 .1 1 .1 1 5 k 1 1 5 6 0 g p 1 1 .0 2 .2 0 1 1 gp d a te n a m e m o d i...
Page 187
P a g e of m ic ro d ri v e ( u l ) u s a - s ta n d a rd 5 5 2 6 ,0 0 1 2 mhtm 0 0 5 k 1 1 5 0 2 + 4 4 = 1 2 3 4 5 6 7 8 9 sa fe ty -l ig h t b a rr ie rs o p ti o n 0 3 0 1 1 1 .1 0 .1 1 5 k 1 1 5 5 4 g p 0 2 0 8 .1 1 .1 1 5 k 1 1 5 6 0 g p 1 1 .0 2 .2 0 1 1 gp d a te n a m e m o d if ic a ti o n ...
Page 189: 18.2 Menu Setup
Barrier mhtm tm microdrive appendix 5815,5001us / version 02.66 189 18.2 menu setup mag00256 a b d c access select 4 1) service information motor gw detector 1 (a-b) radio control main menu prog. Mode setup attachments ethernet factory settings detector 2 (c-d) 2) 3) warnings inputs detector 1 (a-b)...
Page 190
Barrier mhtm tm microdrive appendix 190 5815,5001us / version 02.66 mag00130e master/slave 2) service information motor gw detector 1 (a-b) detector (c-d) out off angle inputs outputs vend count impact settings main menu prog. Mode attachments barrier speed delays open close hold-open time closing d...
Page 191
Barrier mhtm tm microdrive appendix 5815,5001us / version 02.66 191 mag00131d 2) software # service information motor gw detector 1 (a-b) factory settings prog. Mode setup temperature hardware version software version serial no. Signal light signal mode a signal mode b lead time start event boom rel...
Page 192
Barrier mhtm tm microdrive appendix 192 5815,5001us / version 02.66 mag0021 1b 2) radio control delete remote control teach in remote control information number of transmitter with remote control without remote control freq. A freq. B freq. Shift ref. A ref. B sensitivity b frequency settings inform...
Page 193: Index
Barrier mhtm tm microdrive index 5815,5001us / version 02.66 193 index a assemble housing ..............................................66 assembly housing...........................................................66 safety light barrier...........................................69 assembly and inst...
Page 194
Barrier mhtm tm microdrive index 194 5815,5001us / version 02.66 malfunctions..................................................... 159 master .............................................................. 136 mhtm tm microdrive service expert ................... 19 modifications .......................
Page 195
Barrier mhtm tm microdrive 5815,5001us / version 02.6 195.
Page 196
F05456868 magnetic automation corporation 3160 murrell road rockledge, florida, 32955 usa tel.: +1 321 635 8585 fax.: +1 321 635 9449 e-mail: info@ac-magnetic.Com internet: www.Ac-magnetic.Com address sales partner:.