1. DL manuals
  2. Majestic Appliances
  3. Washer
  4. MJ-9000V
  5. Technical Manual

Majestic Appliances MJ-9000V Technical Manual

Other manuals for MJ-9000V: Installation Manual, Owner's Manual, Owner's Manual

Summary of MJ-9000V

  • Page 1

    1 mj9000v technical manual mj9900 installation dimension.

  • Page 2: Problem

    2 your machine, has a solution to every problem we have put together here a few questions which may come what to do if.

  • Page 3: Problem

    3 to mind when you start using your machine, you will see for yourself that your new washer dryer can give a convincing and state of the art reply to all of them. This machine has been designed to adapt the washing process to all types of fabric and to treat your washing in the most delicate way pos...

  • Page 4: This Machine

    4 we would also advise you to place your washer-dryer in such a way that there is some space-even a fraction of an inch-all sides. (fig.1) first of all, remember to switch off the electricity. Then, to clean the body and any rubber parts use a damp cloth and a little soap. Avoid petrol or other solv...

  • Page 5

    5 3. Clean the detergent dispenser every so often. This is very simple and should be done with water. Your machine has an extractable dispenser to make it even easier. Just pull it upwards and out, as shown in fig.2 (fig.2) 4. Your washer-dryer is equipped with a self-cleaning pump. It is therefore ...

  • Page 6

    6 check that: the tap is open and properly connected to the inlet pipe; the inlet pipe is not bent. Check that: the inlet pipe is placed at least 80cm/32 inches above ground level. Check that: the inlet pipe is not blocked; the inlet pipe is not connected at a height more then 1 metre/40 inches abov...

  • Page 7

    7.

  • Page 8

    8 washing machines ref.Models mj9000v description 01 back panel 02 cabinet assembly 03 top panel assembly 04 rest for hose and cable 05 board panel 06 switch cover 07 lamp cover 08 timer (washing) knob 09 timer (drying) knob 10 dispenser handle 11 micro delaying device 12 porthole catch 13 porthole ...

  • Page 9

    9.

  • Page 10

    10 washing machines ref.Models mj9000v description 01 tub 02 drum 03 tub cover gasket 04 tub front flange 05 “u” bolt 06 porthole gasket 07 front counterweight 08 detergent recovery hose 09 hose tub to pump 10 hose dispenser to tub 11 shock absorber 12 shock absorber support 13 tub suspension spring...

  • Page 11

    11.

  • Page 12

    12 washing machines ref.Models mj9000v description 01 dry timer 02-05-45 pressure switch hose 03-04 pressure switch 06 wash timer 07 “y” coupling 08 transmission to detergent tray 09 cam follower 10 bush to timer cam 11 timer cam 12 cable assembly 13 pump 14-15 capacitor 16 motor 17 nut m6 18 motor ...

  • Page 13

    13.

  • Page 14

    14 washing machines ref.Models mj9000v description 1 fan motor 2 the wire with fuse 3 thermostat 2tt nc 125/85 4 upper body of blower 5 reflecting screen wdm 6 heating element 7 gasket of blower body wdm 8 lower body of blower 9 zipper for porthole gasket and blower 10 fan nut 11 fan group 12 clips.

  • Page 15

    15.

  • Page 16

    16.

  • Page 17

    17 timer removal and installation removal: 1 _ disconnect power from machine. 2 _ remove the top panel assembly by unfixing the two screws st3.5x13. Timer for 9900\9000v\9200w 3 _ pull out the timer knob. Round the cam clockwise, let you can see two m5x5 screws, 4 _ unfix two screws size m5x5, and t...

  • Page 18

    18 8p socke t m4 ground connection 8p connector terminal description resistance 1-2 auxiliary winding (spin) 5.3-5.8_ 1-6 primary winding (spin) 2.8-3.2 _ 2-6 aux and primary winding (spin) 7.7-8.01 _ 3-5 common and aux winding((wash) 9.6-9.7 _ 5-7 common and primary winding (wash) 9.6-9.7 _ 3-7 aux...

  • Page 19

    19 how to change pressure switch this machine has a 1levle pressure switch and 2 level pressure switch. A: 2 level pressure switch 1_ disconnect power and water supply from machine. 2_ move the machine to an open space for repair. 3_ remove back panel by removing three size sd3.5x13mm screws. 4_ rem...

  • Page 20

    20 7_ connect housings of wiring to switch as fellow: housing no: pv11 to 11 terminal of switch, housing no: pv12 to 12 terminal of switch, housing no: pv13 to 13 terminal of switch, housing no: pv21 to 21 terminal of switch, housing no: pv22 to 22 terminal of switch, housing no: pv23 to 23 terminal...

  • Page 21

    21 2_test c1=80uf c2=80uf 3_connect to wiring connect c1, c1x terminals of wiring to c1. Connect c2, c2x terminals of wiring to c2. Speed regulator 1_picture c1 c2.

  • Page 22

    22 2_removal and connection 1 _disconnect power from machine. 2 _remove the top panel assembly by unfixing the two screws st3.5x13. 3 _unfix two screw size sd3.5x13 from the back of cabinet ,take off the speed regulator support. 4_ pull out all terminals from regulator assembly. 5 _take out regulato...

  • Page 23

    23 plug terminal rv7 of wiring to 7 terminal of regulator 8 _plug speed regulator to regulator support until clamp in action. 9 _use two screw sd3.5x13 fix regulator assembly to cabinet. 10_ test the machine to sure the machine can work normal. 11_ recovery the top panel assembly. 12_ complete. How ...

  • Page 24

    24 fan motor connection: plug terminal mv of wiring to upper terminal of fan motor. Plug terminal tf of wiring to lower terminal of fan motor. Pump 1_picture 2_connection to wiring.

  • Page 25

    25 fan heat element.

  • Page 26

    26 wire with fuse and thermostat 2tt nc 125/85 17 connection of dryer 1,plug mv terminal of wiring to upper terminal of fan motor 2,plug tf terminal of wiring to lower terminal of fan motor 3,plug fex and fe terminals of wiring to terminals with red point of thermostats 4,plug fdx and fd terminals o...

  • Page 27

    27.