- DL manuals
- Makeblock
- Toy
- mDrawBot Kit
- User Manual
Makeblock mDrawBot Kit User Manual
Summary of mDrawBot Kit
Page 2
1 3 part list quick intro ※mdrawbot is an advanced transformable drawing robot kit based on makeblock platform. It can be assembled into 4 forms — mscara, mspider, meggbot and mcar. It also comes with a matched software named mdraw. 12 tip 9 pen lift mechanism 11 mscara check the parts according to ...
Page 3
Part list 3× beam0324-184 2× beam0824-096 1× beam0824-032 3× bracket 3×3 3× plate 3×6 1× bracket u1 4× timing pulley slice 90t 2× 42byg stepper motor bracket 2× plastic timing pulley 90t 2× tire 90t b 1× caster wheel 2× rubber blanket 2× shaft connector 4mm 2× timing pulley 18t 1× pen holder and v c...
Page 4
5 tip ※with too many parts contained in this product, please assemble the drawbot as per the steps indicated in this instruction to avoid confusion. Pay especially attention to the mark of “o”,”x”. Make sure you are doing exactly as required by the diagram marked with "o", otherwise the parts may be...
Page 5
2.Make sure all parts are placed evenly before tightening the screws. O x o x x o 3.Press downward the parts related to the shaft with force to eliminate the gap before tightening the screw m3x5. Pressure pressure o x 7 6.
Page 6
Makeblock orion & battery holder headless set screw m3×5 wrench nut m4 hex allen key 1.5mm screw m3×8 screw m4 tools pen lift mechanism assembled diagram rubber bank pen 9g servo motor servo motor bracket pen holder and v clamp(together) square nut m4 1 pen holder(1) plastic hinge(1) hinge gasket(1)...
Page 7
4 (1) (1) (1) nut m2(2) screw m2×10(2) (1) 5 the long side is upturned. The short side is downturned. Steering wheel ※you can change the installation angle of the steeling wheel to adjust the height of pen. Screw m4×16(2) nut m4(2) two plates are joint together. 6 (1) x o ※pay attention to the direc...
Page 8
Mscara mspider meggbot mcar 7 (2) 6 (1) screw m3×5(2) 1.5mm make sure the end of the shaft is pushing against the desktop. 8 screw m4×22(4) (2) (1) nut m4(4) (1) (2) 9 (2) o x desk circle shaft4×80 desktop flange bearing 4×8×3 plastic rivet r4120 3 2 1 10 (1) screw m3×5(1) 1.5mm 2 shaft collar 4mm 1...
Page 9
15 screw m4×16(2) (1) 16 (1) screw m3×5(1) 1.5mm (1) 1 2 17 o x 18 screw m3×8(4) to avoid over-tension,do not tighten the screw. Timmy pulley 18t 21 (2) o x 22 (1) screw m3×5(1) 1.5mm 1 2 shaft collar 4mm 19 (1) nut m4(1) 20 screw m4×16(4) (1) (1) nut m4(4) (1) (2) 15 14 mscara mspider meggbot mcar ...
Page 10
23 (1) (1) screw m3×8(4) 24 112mxl(1) (1) 25 screw m4×16(2) nut m4(2) tight timmy pulley 18t 26 screw m3×5(1) 1.5mm 27 screw m4×8(2) nut m4(2) pen lift mechanism 28 screw m4×8(8) refer to page 8 (4) (1) 29 screw m4×8(2) 30 screw m4×16(4) (2) nut m4(4) 31 (2) nut m4(2) screw m4×8(2) 17 16 mscara mspi...
Page 11
Mscara mspider meggbot mcar 32 6p6c rj25 cable-20cm(2) 6p6c rj25 cable-35cm(1) micro usb cable(1) ac/dc adapter 12v2a(1) screw m4×16(2) nut m4(2) (2) screw m4×35(1) nut m4(3) (1) (1) (1) screw m4×8(4) nut m4(2) mspider 1 (2) (1) screw m4×22(2) nut m4(2) motor a motor b string a 2 3 4 string b 19 18 ...
Page 12: ×2
5 screw m4×8(2) pen lift mechanism 6 (1) (1) screw m4×8(2) (1) screw m4×16(4) 7 (1) screw m3×8(4) nut m4(4) ×2 ×2 mscara mspider 8 (1) (1) screw m4×16(2) 9 screw m4×16(3) (2) nut m4(3) 10 2m(1) ×2 ×2 ×2 ※the length of the string is around 8 meters, you can cut it into 2 strings with 4 meters each at...
Page 13
16 motor b string b o x 17 (2) 18 string a string b mscara mspider meggbot mcar 19 screw m4×8(8) refer to page 8 (4) (1) 20 screw m4×16(4) (2) nut m4(4) screw m4×16(2) nut m4(2) 21 rj25 adapter(1) 22 6p6c rj25 cable-20cm(2) 6p6c rj25 cable-35cm(1) micro usb cable(1) 9g servo extension cord(1) ac/dc ...
Page 14
Meggbot motor a motor b egg (2) 1 screw m4×8(8) (2) 2 (1) (1) screw m3×8(4) 3 screw m4×16(2) nut m4(2) 1 2 5 (1) screw m4×22(2) nut m4(4) (2) 6 nut m4(2) flange bearing 4×8×3 plastic gasket 4×8×1 7 (1) 4 (1) screw m3×5(1) 1.5mm mscara mspider meggbot mcar mscara mspider meggbot mcar 24 25 (5~8) mm s...
Page 15
10 (1) (1) spring 11 screw m3×5(1) compress the spring. 12 (2) 13 screw m4×8(2) nut m4(2) 14 screw m4×8(2) nut m4(2) (1) (1) (2) 15 1.5mm 26 27 (1) 8 4×80(1) 4×7×3(1) 4×7×10(2) plastic gasket 4×7×3 plastic gasket 4×7×10 flange bearing 4×8×3 circle shaft 4×80 (5~8) mm 1 2 9 screw m3×5(1) (1) (5~8) mm...
Page 16
18 (1) (1) screw m3×5(1) (1) screw m3×8(3) o x 1 2 19 screw m4×16(2) nut m4(2) 20 112mxl(1) 4×7×3(4) 4×7×10(2) nut m4(2) screw m4×22(2) 21 screw m4×16(2) (1) nut m4(2) 22 screw m4×8(2) nut m4(2) (1) 23 screw m4×8(2) nut m4(2) pen lift mechanism 1.5mm 28 29 16 (1) nut m4(1) 17 (1) screw m3×5(1) 1.5mm...
Page 17: ×2
Mscara mspider meggbot mcar mscara mspider meggbot mcar 24 screw m4×8(8) refer to page 8 (4) (1) 25 screw m4×16(4) (2) nut m4(4) screw m4×16(2) nut m4(2) 26 rj25 adapter(1) 27 6p6c rj25 cable-20cm(2) 6p6c rj25 cable-35cm(1) micro usb cable(1) ac/dc adapter 12v2a(1) mcar motor a 1 screw m4×8(4) (2) (...
Page 18: ×2
5 screw m4×16(2) nut m4(2) 1 2 2 6 (1) (1) screw m4×16(2) ×2 (2) 8 7 screw m3×5(2) 1.5mm o x 1 1 2 2 screw m3×5 mscara mspider meggbot mcar mscara mspider meggbot mcar threaded hole 10 screw m4×16(2) screw m4×16(2) nut m4(2) 11 9 (1) nut m4(4) screw m4×22(2) (1) 1 1 2 2 13 mm screw m4×16(2) nut m4(2...
Page 19
Mscara mspider meggbot mcar mscara mspider meggbot mcar screw m4×16(2) nut m4(2) 13 4×7×3(2) (1) me stepper motor driver screw m4×16(2) nut m4(2) 14 4×7×3(2) (1) me stepper motor driver screw m4×8(2) nut m4(2) 15 refer to page 8 16 6p6c rj25 cable-20cm(2) 6p6c rj25 cable-35cm(1) assembled diagram so...
Page 20
36 warnings • adult supervision and assistance are required. • choking hazard — this product contains small parts and functional sharp points on components. Keep away from children under age 3. • read and follow all instructions in the user guide before using. • retain this user guide for future ref...