I n s t r u c t i o n m a n u a l warning: for your personal safety, read and understand before using. Save these instructions for future reference. W w w . M a k i t a t o o l s . C o m portable cut-off model 2414nb 003753 double insulation.
2 specifications • manufacturer reserves the right to change specifications without notice. • specifications may differ from country to country. For your own safety read instruction manual before operating tool save it for future reference general safety precautions usa007-1 (for all tools) 1. Know ...
3 11. Always use safety glasses. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are not safety glasses. 12. Secure work. Use clamps or a vise to hold work when practical. It’s safer than using your hand and it frees both hands to...
4 use proper extension cord. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table 1 shows t...
5 11. Before using the tool on an actual work- piece, let it run for a while. Watch for vibration or wobbling that could indicate poor installation or a poorly balanced wheel. 12. Watch out for flying sparks when operat- ing. They can cause injury or ignite com- bustible materials. 13. Remove materi...
6 installation securing cut-off this tool should be bolted with two bolts to a level and stable surface using the bolt holes provided in the tool’s base. This will help prevent tipping and possible personal injury. Functional description caution: • always be sure that the tool is switched off and un...
7 stopper plate the stopper plate prevents the cut-off wheel from contacting the workbench or floor. When a new wheel is installed, set the stopper plate to position (a). When the wheel wears down to the extent that the lower portion of the workpiece is left uncut, set the stopper plate to position ...
8 assembly caution: • always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Removing or installing cut-off wheel to remove the wheel, raise the safety guard. Press the shaft lock so that the wheel cannot revolve and use the socket wrench to loosen the h...
9 when the cut-off wheel has worn down considerably, use a spacer block of sturdy, non-flammable material behind the workpiece as shown in the figure. You can more efficiently utilize the worn wheel by using the mid point on the periphery of the wheel to cut the workpiece. When cutting workpieces ov...
10 operation hold the handle firmly. Switch on the tool and wait until the wheel attains full speed before lowering gently into the cut. When the wheel contacts the workpiece, gradually bear down on the handle to perform the cut. When the cut is com- pleted, switch off the tool and wait until the wh...
11 maintenance caution: • always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free t...
Memo 12.
13 first-class postage required post office will not deliver without proper postage. Makita u.S.A., inc. 14930 northam street la mirada, ca 90638-5753 fold cut.
14 1. This product was purchased from: home center hardware/lumber store tool distributor industrial supply construction supply other ( ) 3. How did you learn about this product: magazine from dealer newspaper store display catalog radio exhibition from friend previous usage other ( ) 2. Use of the ...
15 factory service centers 1-800-4-makita retain this portion for your records arizona 3707 e. Broadway rd., ste. 6 phoenix, az 85040 (602) 437-2850 california 41850 christy st. Fremont, ca 94538-5107 (510) 657-9881 14930 northam st. La mirada, ca 90638-5753 (714) 522-8088 1970 fulton avenue sacrame...
Warning some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the state of california to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline ...
