1. DL manuals
  2. Makita
  3. Drill
  4. 6041D
  5. Instruction Manual

Makita 6041D Instruction Manual

Other manuals for 6041D: Instruction Manual, Instruction Manual

Summary of 6041D

  • Page 1

    I n s t r u c t i o n m a n u a l warning: for your personal safety, read and understand before using. Save these instructions for future reference. Cordless driver drill model 6041d model 6076d model 6176d 002864.

  • Page 2: Specifications

    2 specifications • manufacturer reserves the right to change specifications without notice. • specifications may differ from country to country. General safety rules usa003-2 (for all battery operated tools) warning: read and understand all instructions. Failure to follow all instructions listed bel...

  • Page 3

    3 electrical safety 4. A battery operated tool with integral bat- teries or a separate battery pack must be recharged only with the specified charger for the battery. A charger that may be suit- able for one type of battery may create a risk of fire when used with another battery. 5. Use battery ope...

  • Page 4: Specific Safety Rules

    4 service 21. Tool service must be performed only by qualified repair personnel. Service or main- tenance performed by unqualified personnel may result in a risk of injury. 22. When servicing a tool, use only identical replacement parts. Follow instructions in the maintenance section of this manual....

  • Page 5: Charger & Battery Cartridge

    5 important safety instructions for charger & battery cartridge usc003-1 1. Save these instructions- this man- ual contains important safety and operat- ing instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) ba...

  • Page 6: Tool

    6 additional safety rules for charger & tool 1. The charger and the tool are specifically designed to work together. Do not attempt to charge any other cordless tool with this charger. Do not attempt to charge the tool with any other charger. 2. Do not charge the tool when temperature is below 10°c ...

  • Page 7: Functional

    7 functional description caution: • always be sure that the tool is switched off before adjusting or checking function on the tool. Charging connect the charging plug to the charging connector, then plug in the charger to the power receptacle. Charging takes 3 hours. Caution: • the battery in your n...

  • Page 8: Reversing Switch Action

    8 reversing switch action this tool has a reversing switch to change the direction of rotation. Move the reversing switch lever to the “fwd” posi- tion for clockwise rotation or the “rev” position for counter- clockwise rotation. When the reversing switch lever is in the neutral position, the switch...

  • Page 9: Operation

    9 operation screwdriving operation place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool slowly and then increase the speed gradually. Release the trigger just as the screw bottoms out. If the trigger is not released, the screw may strip out the hole or t...

  • Page 10: Maintenance

    10 • a stuck bit can be removed simply by setting the reversing switch to reverse rotation in order to back out. However, the tool may back out abruptly if you do not hold it firmly. • always secure small workpieces in a vise or similar hold- down device. Maintenance caution: • always be sure that t...

  • Page 11: Recycling The Battery

    11 en0001-1 recycling the battery the only way to dispose of a makita battery is to recycle it. The law prohibits any other method of disposal. To recycle the battery: 1. Remove the battery from the tool. 2. A) take the battery to your nearest makita factory ser- vice center or b) take the battery t...

  • Page 12: Memo

    Memo 12.

  • Page 13: Makita Canada Inc.

    13 fold cut stamp timbre makita canada inc. 1950 forbes street, whitby, ontario l1n 7b7.

  • Page 14

    14 your answers to the following questions are appreciated. Date purchased model no. Serial no. Initial last name street address city province age: male female married single month day year 20 under 19 20-29 30-39 40-49 over 50 paste paste paste paste paste paste paste paste p aste p aste p aste p a...

  • Page 15: Factory Service Centres

    15 factory service centres for the authorized service centre nearest you please refer to the local yellow pages directory under “tools” or con- tact our customer service department (tel) 1-800-263-3734 when you need service... • explain the problem in a letter • enclose the letter with the tool • pa...

  • Page 16

    Warranty policy every makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of one year from the date of original purchase. Should any trouble develop during this one year period, return the comp...