1. DL manuals
  2. Makita
  3. Impact Driver
  4. DA6300
  5. Instruction Manual

Makita DA6300 Instruction Manual - Functional

Summary of DA6300

  • Page 1

    I n s t r u c t i o n m a n u a l warning: for your personal safety, read and understand before using. Save these instructions for future reference. Impact wrench 25.4 mm (1”) model 6910 002293.

  • Page 2: Specifications

    2 specifications • manufacturer reserves the right to change specifications without notice. • specifications may differ from country to country. General safety rules usa001-2 (for all tools) warning: read and understand all instructions. Failure to follow all instructions listed below, may result in...

  • Page 3

    3 qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically mal- function or break down, grounding provides a low resistance path to carry electricity away from the user. 5. Avoid body contact with grounded sur- faces such as pipes, rad...

  • Page 4

    4 22. Use only accessories that are recom- mended by the manufacturer for your model. Accessories that may be suitable for one tool, may become hazardous when used on another tool. Service 23. Tool service must be performed only by qualified repair personnel. Service or main- tenance performed by un...

  • Page 5: Specific Safety Rules

    5 an adapter fig. “b” and “c” is available for connecting fig. “a” type plugs to two- prong receptacles. The green-colored rigid ear, lug, etc., extending from the adapter must be con- nected to a permanent ground, such as a properly grounded outlet box. Specific safety rules usb003-2 do not let com...

  • Page 6: Save These Instructions

    6 save these instructions warning: misuse or failure to follow the safety rules stated in this instruction manual may cause serious personal injury..

  • Page 7: Functional

    7 functional description caution: • always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Switch action caution: • before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “off” position when...

  • Page 8: Operation

    8 installing or removing socket to install the socket, push it onto the anvil of the tool until it locks into place. To remove the socket, simply pull it off. Operation the proper fastening torque may differ depending upon the kind or size of the bolt, the material of the workpiece to be fastened, e...

  • Page 9

    9 note: • hold the tool pointed straight at the bolt or nut. • excessive fastening torque may damage the bolt/nut or socket. Before starting your job, always perform a test operation to determine the proper fastening time for your bolt or nut. The fastening torque is affected by a wide variety of fa...

  • Page 10: Maintenance

    10 maintenance caution: • always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free t...

  • Page 11: Memo

    Memo 11.

  • Page 12: Memo

    Memo 12.

  • Page 13: Makita Canada Inc.

    13 fold cut stamp timbre makita canada inc. 1950 forbes street, whitby, ontario l1n 7b7.

  • Page 14

    14 your answers to the following questions are appreciated. Date purchased model no. Serial no. Initial last name street address city province age: male female married single month day year 20 under 19 20-29 30-39 40-49 over 50 paste paste paste paste paste paste paste paste p aste p aste p aste p a...

  • Page 15: Factory Service Centres

    15 factory service centres for the authorized service centre nearest you please refer to the local yellow pages directory under “tools” or con- tact our customer service department (tel) 1-800-263-3734 when you need service... • explain the problem in a letter • enclose the letter with the tool • pa...

  • Page 16

    Warranty policy every makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of one year from the date of original purchase. Should any trouble develop during this one year period, return the comp...