Cordless steel rod cutter dsc250 instruction manual before installing and operating this machine, read, understand and follow all instructions and operating procedures. Keep this instruction manual with the machine. En glish : or igina l ins tr uc tions read before use..
2 english read, understand and follow all safety instructions and operating procedures. If you do not understand the instructions, or if condi- tions are not correct for proper operation, do not operate the machine. Consult your supervisor or other responsible person. Specifications model: dsc250 vo...
3 english vibration the vibration total value (tri-axial vector sum) deter- mined according to en60745: work mode: impact tightening of fasteners of the maxi- mum capacity of the tool vibration emission (a h ) : 2.5 m/s 2 uncertainty (k) : 1.5 m/s 2 note: the declared vibration emission value has be...
4 english caution 1. Work area safety · keep work area clean and well lit. Cluttered or dark areas invite accidents. 2. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 3. Store idle power tools correctly. · store idle power tools out of the...
5 english electrical safety 1. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. 2. Avoid body contact with earthed or grounded surfaces...
6 english 14. Do not operate the tool close to flammable and fragile items or personnel not necessary to the operation. During cutting hot debris and sparks will be ejected from the tool which may cause damage to the surroundings, fire or personal injury. 15. Do not cut concrete. It causes damage to...
7 english important safety instructions for battery cartridge 1. Before using battery cartridge, read all instruc- tions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 2. Do not disassemble battery cartridge. 3. If operating time has become excessively sh...
8 english 1 2 2 1 3 fig.2 ► fig.2: 1. Button 2. Red indicator 3. Battery cartridge to remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge. To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housin...
9 english operation 1 2 1 2 fig.5 ► fig.5: 1. Guide 2. Rebar 1 2 fig.6 ► fig.6: 1. Rebar 2. Guide 1. Screw the handle into threaded hole at the vertical or parallel position for easier operation. 2. Ensure that the switch is at “o” position. Caution: as a safety function of this tool, the motor cann...
10 english 4. The surface of the cut piece is discolored by heat. Note: tipped saw blades cannot be resharpened. How to fit the dust bag 1 fig.7 ► fig.7: 1. Dust bag 1. Place the open end of the dust bag over the dust bag holder and secure in place with the draw strings. 2. Give the bag a sharp tug ...
11 english protection lock when the protection system works repeatedly, the tool will lock and the battery indicator shows the state as table 3. Table 3 battery indicator :on :off :blinking protection lock works overheat protection for tool when the tool is overheated, the tool stops auto- matically...
12 english replace the tipped saw 1 fig.12 ► fig.12: 1. Push (lock button) 1. Fit the tipped saw over the output gear, making sure that the slot in the flange is properly aligned with the key. 2. Replace the tipped saw guide. 3. Replace the bolt and washer. 4. Push in the lock button completely to p...
13.
14.
15.
Www.Makita.Com makita europe n.V. Makita corporation 3-11-8, sumiyoshi-cho, anjo, aichi 446-8502 japan jan-baptist vinkstraat 2, 3070 kortenberg, belgium dsc250-eneu-1610 en 20161019.
