Summary of ESS
Page 1
En.
Page 2
En ess ess - 23/02/2016 17:00:00 user instructions and safety congratulations on your purchase of an n-com product. N-com ess was made using the most advanced technologies and the best materials. The system can only be installed on the pre-set nolan n-com helmets. Check on the website www.N-com.It t...
Page 3
Contents 1. Warnings and safety ................................................................................................................... 4 1.1. Road safety.........................................................................................................................................
Page 4
En 4 1. Warnings and safety read this user manual carefully, as well as the simple rules listed below. Failure to comply with these rules may lead to dangerous situations. Caution: the product cannot be used in official or non-official competitions, motordromes, circuits, racing tracks and the like....
Page 5
Ess 5 1.2. Switching on the system in safe environments do not turn on the n-com system whenever their use is forbidden or when the devices can cause interference or dangerous situations. Turn off while refueling. Do not use the n-com system in filling stations. Do not use the device near combustibl...
Page 6
En 6 1.5. Accessories and batteries only use the type of batteries, battery chargers and accessories approved by nolan for the specific model. The use of a battery type different from the recommended one may lead to dangerous situations and invalidate the warranty. Contact your local dealer to see a...
Page 7
Ess 7 1.6. Disposal refer to this user manual and to manuals related to other parts of the n-com system in order to disassemble the system from the helmet. Once the system has been disassembled, dispose of it according to the following instructions: the presence of a crossed-out wheelie bin indicate...
Page 8
En 8 2. Content of the packaging ess system mini usb wire key helmet adapters helmet adapter double-sided adhesive tape function key helmet model.
Page 9
Ess 9 3. Installation important: prior to installing the n-com system, it is recommended to write down the identification code affixed to the product (see chapter 9.5). remove the cheek padding (see helmet instructions). Fig. 1 remove the helmet edge gasket using the special tool (fig. 1). com...
Page 10
En 10 fig. 2 select the specific adapter for your helmet (the compatible helmet model is shown on the back of the support). N.B.: the installation of the ess system on an n87 helmet requires no adapter. remove the protective film from the double-sided adhesive tape located in the rear of the sys...
Page 11
Ess 11 fig. 4 insert the flex cable of the ess system in the hole of the selected adapter as illustrated, in the direction shown in the image (fig. 4); fig. 5 rotate the adapter until it is in a horizontal position like the ess system, then press the two components together until they stick one ...
Page 12
En 12 fig. 6 place the system in the special housing in the back of the helmet, pushing it all the way into the groove (fig. 6). Important: make sure the flex cable is not pulled too tightly. Fig. 7 open the rubber cap of the ess system. reassemble the edge gasket, securing it with the special...
Page 13
Ess 13 fig. 8 remove the protective film from the double-sided adhesive tape of the helmet adapter (fig. 8) and apply the ess system to the shell (fig. 9). Attention: position the “n” of the ess system at the shell edge gasket screw, so that the adapter is lined up with the helmet lines. Fig. 9 ...
Page 14
En 14 3.1. Removing the ess system from the helmet proceed as follows to remove the ess system from the helmet: fig. 10 remove the ess light from the shell (fig. 10). Fig. 11 remove the cheek padding and the shell gasket; completely remove the ess system from helmet using a flat head screwdriv...
Page 15
Ess 15 4. Basic function the ess system features a menu with 3 operating modes: emergency stop signal, real light, poor visibility light. To scroll through this menu, briefly press the function key. Every time you press the key, the system switches to the next mode. Mode functions 0 on/off switching...
Page 16
En 16 switching on press the function key until the led turns on. Every time it is turned on, the system positions itself in mode 1. Switching off to switch off the system, put it in mode 0. Briefly press the function key and release it to switch from one mode to the other. Switch off is confirmed b...
Page 17
Ess 17 5. Emergency stop signal (mode 1) the ess system is equipped with a led system to assist emergency braking. In case of sudden braking, the leds on the ess flash for a few seconds. The sensitivity of the stop signal can be adjusted in 3 different levels: low: the stop signal turns on during su...
Page 18
En 18 6. Rear light (mode 2) the tail light makes it possible to activate the bottom leds of the ess system, keeping them on during the entire ride. If the emergency brake light is activated during braking, all leds will start flashing. 7. Poor visibility light (mode 3) the poor visibility light all...
Page 19
Ess 19 8. Battery and recharge during its operation, the system alerts the user when the battery is running down. The top leds start to flash to indicate that the battery is in “reserve” mode. 8.1. Recharging the system fig. 12 to charge the system, hook it up to a usb outlet powered with the usb-...
Page 20
En 20 9. Limited warranty with this limited warranty certificate, nolangroup warrants this product to be free from defects in material and workmanship at the time of its original purchase by the buyer. We invite you to: - read the cautions pertaining to safety and proper use. - read the warranty ter...
Page 21
Ess 21 colour changes or damages caused by exposure to harmful chemical products. the use of incompatible accessories that are not part of the n-com product range. moreover, the warranty does not cover product defects caused by fortuitous events, modifications or adjustments, causes of force m...
Page 22
En 22 9.3. Validity of this limited warranty this warranty is valid only if the enclosed warranty form is duly and completely filled out with the following information: product identification code name and stamp of the authorized dealer. Product purchase date. Buyer’s name and address. Nolangroup re...
Page 23
Ess 23 this warranty voids and replaces any other written or verbal warranties provided for by the law that can be derogated at the parties’ will; specifically, nolangroup does not grant specific warrants of merchantability or fitness for a particular purpose. In no case shall nolangroup be liable f...
Page 24
10. Warranty registration form product name: ess identification code buyer’s information name last name address phone e-mail dealer’s stamp date of purchase.