12/29/2005 1 300 series media converter & industrial ethernet switches installation guide.
12/29/2005 2 industrial ethernet switch installation guide 302mc-xx 302mce-xx-yy 304tx 305fx-xx 305fxe-xx-yy 306tx 306fx2-xx 306fxe2-xx-yy 308tx where: xx = st or sc and yy = -15, -40, or -80
12/29/2005 3 copyright, © n-tron corp., 2005 820 s. University blvd., suite 4e mobile, al 36609 usa all rights reserved. Reproduction, adaptation, or translation without prior written permission from n-tron corp. Is prohibited, except as allowed under copyright laws. Ethernet is a registered tradema...
12/29/2005 4 safety warnings electrical safety warning: disconnect the power cable before removing the enclosure top. Warning: do not operate the unit with the top cover removed. Warning: do not work on equipment or cables during periods of lightning activity. Warning: do not perform any services on...
12/29/2005 5 hazardous location installation requirements 1. Warning! Do not disconnect while circuit is live, unless area is known to be non-hazardous. 2. Warning! Install only in accordance with local & national codes of authorities having jurisdiction. 3. Class i, div 2 installations require that...
12/29/2005 6 300 series industrial ethernet switches the 300 series unmanaged industrial ethernet switches support high speed layer 2 switching between ports. All n-tron 300 series switches are housed in a ruggedized steel enclosure, and provide category-5 compliant 10/100-baset connections for high...
12/29/2005 7 package contents please make sure the ethernet switch package contains the following items: 1. 300 series unit 2. N-tron product cd contact your carrier if any items are damaged. Installation read the following warning before beginning the installation: warning fxe units contain a class...
12/29/2005 8 din-rail mounting install the unit in a standard din-rail. Recess the unit to allow at least 5” of horizontal clearance for fiber optic cable bend radius (2” for tx models). To install the unit to 35mm industrial din-rail, place the top edge of the included mounting bracket on the back ...
12/29/2005 9 front panel lnk link led for fiber optic ports tx fiber optic transmit ports rx fiber optic receive ports act activity led for fiber optic ports rj45 ports ports 1-4 auto sensing 10/100baset connections green led lights when power is connected note: each rj45 data port has two led’s for...
12/29/2005 10 applying power (top view) unscrew & remove the dc voltage input plug from the top header. Install the dc power cables into the plug (observing polarity on unit). Plug the voltage input plug back into the top header. All led’s will flash on momentarily verify the power led stays on (gre...
12/29/2005 11 troubleshooting 1. Make sure the (power led) is on. 2. Verify that link led’s are on for connected ports. 3. Verify cabling used between stations. 4. Verify that cabling is category 5 (or greater) for 100mbit operation. 5. Verify tx is connected to far end rx and vise versa (fiber opti...
12/29/2005 12 key specifications physical height: 3.98” (max.) width: 2.01” (max.) depth: 4.19” (max.) weight: 0.75 lbs. Electrical input voltage: 10-30 vdc (regulated) input current: 290ma max. @ 24vdc (steady state) inrush current: 8.0amp/0.6ms max. @ 24vdc input ripple: less than 100 mv input wir...
12/29/2005 13 n-tron limited warranty n-tron, corp. Warrants to the end user that this hardware product will be free from defects in workmanship and materials, under normal use and service, for the applicable warranty period from the data of purchase from n-tron or its authorized reseller. If a prod...
