NAD D 3020 Owner's Manual - page 5
IDENTIFICATION OF CONTROLS
1 o (STANDBY)
• With the corresponding end of the mains power cord connected
to the AC mains input of the D 3020 and the plug connected to a
mains power source, press o (Standby) to switch ON the D 3020
from standby mode. The Standby indicator will turn from amber to
bright/white color.
• Press and hold o (Standby) until D 3020 switches back to standby
mode.
AUTO STANDBY
The D 3020 can be setup to automatically go to standby mode if there
is no user interface interaction and no active source input within
30 minutes. Auto standby mode can be enabled or disabled by the
following steps.
Enable Auto Standby mode
• While at standby mode, press and hold the remote control’s “OFF”
button until the whole display wakes up and flashes once.
• At operating mode and with auto standby enabled, the D 3020
will automatically go to standby mode if there is no user interface
interaction and no active source input within 30 minutes.
Disable Auto Standby mode
• While at standby mode, press and hold the remote control’s “OFF”
button until the whole display wakes up and flashes twice.
• At operating mode and with auto standby disabled, D 3020 will not
automatically go to standby mode even if there is no user interface
interaction and no active source input within 30 minutes. Press
o (Standby) to switch D3020 from operating mode to standby
mode.
2 S (SOURCE)
• Toggle to cycle through the Sources (OPT1, OPT2, COAX, USB, AUX
1, AUX 2, BT) and select desired Source.
3 VOLUME
• Adjust audio level by turning clockwise or counterclockwise.
· Rotating the volume knob will automatically restore audio from
mute mode.
4 DISPLAY
• Illuminate the selected or active Source (OPT1, OPT2, COAX, USB,
AUX 1, AUX 2, BT) and current audio level.
IMPORTANT NOTE
Display will not adjust to the orientation of the unit. Display is best
viewed with the D3020 in vertical position as shown above.
5 PHONES
• A 3.5 mm stereo jack socket is supplied for headphone listening.
• Specially designed low noise headphone circuitry can accommodate a
wide range of phones, even 600 Ohm studio models.
• Adjust headphone audio level by rotating the VOLUME control
clockwise or counterclockwise.
• Ensure that the volume control is turned to minimum (fully
counterclockwise) before connecting or disconnecting
headphones. Listening at high levels can damage your hearing.
• Inserting a headphone jack into this socket automatically switches
off the loudspeakers.
6 BASS EQ
• Boost overall bass response by at least 6 dB. “BASS” is illuminated in
the display with BASS EQ enabled.
• Toggle to enable or disable BASS EQ.
7 AUX 1
• Use a twin RCA-to-RCA lead to connect these sockets to the left and
right analog output of a CD player, preamplifier, processor or other
applicable devices.
8 AUX 2
• Connect to corresponding output connectors of other audio
devices using a 3.5mm stereo plug (not supplied). This input also
accepts headphone/digital audio output from a MacBook Pro.
• Install the supplied TOSLINK mini-adapter to convert this input into
an additional digital optical input (OPT2).
9 SUBW
• Connect the SUBW output to powered (“active”) subwoofers or to
power amplifier channels driving a passive system.
USB
DIGITAL AUDIO INPUT
LEFT
SPEAKERS
+12V
TRIGGER
IN
L
R
COAXIAL
OPTICAL 1
RIGHT
AUX 1
OPTICAL 2
ANALOG AUDIO INPUT
Bass EQ (SERVICE)
SUBW
AUX 2
6
7
8
9
10
11
12
13
14
1
2
3
4
5
5
ENGLISH
POR
TUGUÊS
FR
ANÇ
AIS
ESP
AÑOL
IT
ALIANO
DEUT
SCH
NEDERL
ANDS
SVENSK
A
РУ
ССКИЙ