English fr anÇ ais esp aÑol it aliano deut sch nederl ands svensk a РУ ССКИЙ ® owner’s manual m2 direct digital amplifier.
Save these instructions for later use. Follow all warnings and instructions marked on the audio equipment. 1 read instructions - all the safety and operating instructions should be read before the product is operated. 2 retain instructions - the safety and operating instructions should be retained f...
19 damage requiring service - unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) when the power-supply cord or plug is damaged. B) if liquid has been spilled, or objects have fallen into the product. C) if the product has be...
Notes on environmental protection at the end of its useful life, this product must not be disposed of with regular household waste but must be returned to a collection point for the recycling of electrical and electronic equipment. The symbol on the product, user’s manual and packaging, point this o...
Introduction getting started quick start in case you simply cannot wait to experience the performance of your new nad m2 direct digital amplifier, we provide the following quickstart instructions to get you underway. Please make all the connections to your m2 with the unit unplugged from the ac outl...
Identification of controls front panel 1 standby led: this indicator will light up amber when m2 is in standby state. When m2 is at on state, this indicator will illuminate blue. 2 standby button: press this button to switch on the m2. The standby led indicator will turn from amber to blue and illum...
13 menu: toggle to view the available options such as level trim and sample rate options for balanced and single-ended input signal as well as selections for speaker compensation and polarity. These menu options are accessed by pressing the menu button and then rotating the volume control knob clock...
1 balanced: connect xlr audio source to these connectors. Ensure that proper pin configurations are followed – pin 1: ground, pin 2: positive (signal live) and pin 3: negative (signal return). 2 single-ended: use a twin rca-to-rca lead to connect to these sockets the left and right analog output of ...
9 +12v trigger in: this input allows the m2 to be switched remotely to standby mode or on by ancillary equipment, such as an amplifier, preamp, av processor, etc. The controlling device must be equipped with a 12 v trigger output to use this feature. 10 +12v trigger out: the +12v trigger out is used...
Example illustration of grounding the m2 via the rear panel ground terminal notes • theaboveillustrationshowsthem2beingconnectedtogroundvia a metal water pipe. There maybe other grounding conductor points in your home. Consult with a licensed electrician to properly locate or correctly install a gro...
1 on: switch m2 on. 2 off: switch m2 off. 3 coax 1-2, opt 1-2, aes/ebu: select coaxial, optical or aes/ebu digital source input. 4 pro loop: activate or deactivate “loop” feature. 5 balanced: select balanced source input. Single-ended: select single-ended source input. 6 mute: temporarily shuts down...
Condition possible causes possible solutions the vfd displays “protection left amp short”. • left output short circuit. • shut down m2 by turning off the rear panel power switch. If there is no action undertaken, the m2 will shut down itself (go to standby mode) within 10 seconds the fault happened....
Digital input (coaxial, optical, aes/ebu) input impedance 75Ω (coaxial) 110Ω (aes/ebu) sample rate 32khz to 192khz frequency response ±0.5db (ref. 20hz - 20khz) -3db (ref. 96khz) channel separation >90db (ref. 10khz, 4Ω, 1/3 rated power) analog input (balanced, single-ended) input impedance 36kΩ//20...
Www.Nadelectronics.Com ©2012 nad electronics international a division of lenbrook industries limited all rights reserved. Nad and the nad logo are trademarks of nad electronics international, a division of lenbrook industries limited. No part of this publication may be reproduced, stored or transmit...
