NAD T775 HD Owner's Manual - page 39
MACRO COMMANDS
A “macro” command is a series of two or more remote codes issued automatically from a single
keypress. You might use a macro to automate a simple command sequence, such as, “Turn on the DVD
player and then press PLAY”. Or you might compose an elaborate macro to power up an entire system,
select a source, choose a Listening Mode, and begin playback—again, all from a single keypress. The
HTR 3 can store one macro on each of its function keys (these exclude the Device Selector keys).
NOTE
Macrosareindependentofthecurrentlyselecteddevice.
RECORDING MACROS
To record a macro, simultaneously press-and-hold for 3 seconds both the [MACRO] key and the HTR 3
function key to which you wish to assign the macro, until the status LED turns green. The macro
button will also light up.
Press the sequence of function keys to be recorded into the macro, being sure to first press the
requisite Device Selector key for each function (you may switch devices while recording the macro as
many times as necessary), allowing you to create macro containing commands from more than one
Device Selector “page.”
When you have finished entering the desired command sequence, press [MACRO] again
to store the macro; the Learn LED and [MACRO] key illumination will turn off.
NOTE
Eachmacrocanstoreamaximumof64commandsteps.Ifyouexceedthisnumber,themacrowill
bestoredautomaticallyafterthe64thcommandisadded.
Example: Record a Macro to the [0] key to Turn on the T 775, Select “Input 1” (Source 1), and
Commence Playback of connected Source 1 device (as in DVD player):
• On the HTR 3, simultaneously press-and-hold [MACRO] and [0] (numeric zero); the Learn LED turns
steady green.
• Press [AMP]; press [ON]; press [1] (“Input or Source 1”); press [DVD]; press [ ] (Play) - the Learn LED
blinks as each step is added.
• Press [MACRO] again to exit the macro-record mode.
To clear a macro, perform the above steps without entering any functions.
EXECUTING MACROS
To execute a macro, press and release [MACRO]; its key illumination lights for 5 seconds. While it
remains lit, press an HTR 3 key to which a macro has previously been stored.
The corresponding macro will run; as each step executes, its “parent” Device Selector’s key flashes lights
briefly; when execution is finished, the [MACRO] key illumination goes out. Pressing any other HTR 3
key while a macro is executing will abort the macro. Remember that you must hold the HTR 3 so that
its infrared emitter can activate the target components.
NOTE
Whenamacroexecutes,a1seconddelayisautomaticallyinsertedbetweenitscommands.If
youneedmorethana1seconddelaybetweenparticularcommands—forexample,topermita
componenttopowerupcompletely—youcanrecord“empty”stepsintothemacrobychanging
DeviceSelector“pages”withoutenteringactualcommandfunctions.
BUTTON ILLUMINATION TIMEOUT
The HTR 3’s key-illumination can be set to remain lit for 0-9 seconds. The default value is 2 seconds. To
set the illumination timeout, simultaneously press-and-hold for 3 seconds both the HTR 3’s [DISP] and
the [0-9] key, with the digit corresponding to the desired timeout duration; the Learn LED will flash
twice to confirm the new setting. When set to zero, the illumination will not turn on at all.
NOTE
KeyilluminationisthebiggestdrainontheHTR3’sbatteries.Ashortkey-illuminationtimeoutwill
extendbatterylifeappreciably;turningitoffaltogether(setitto0seconds)willlengthenitstill
further.
OPERATION
USING THE HTR 3 REMOTE CONTROL
39
EN
G
LI
SH
FR
ANÇ
AIS
ESP
AÑOL
IT
ALIANO
DEUT
SCH
NEDERL
ANDS
SVENSK
A
РУ
ССКИЙ