NAD T785 Owner's Manual - page 25
AMPLIFIER SETUP
If the surround back speakers are not used in the main zone, their surround back amplifier channels
could be assigned for Main back, Main Front (Bi-Amp) and multi-zone use.
The Surround Back amplifier is configurable through the following settings
• MainBack: Assign as surround back speakers.
• MainFront(Bi-Amp): Provide a bi-amp mode for the Main Front speakers (Left and Right)
speakers thus reproducing the Front Left and Front Right amplifier channel outputs.
• Zone2: Assign the surround back amplifier channels to supply Zone 2 speaker level outputs from
the surround back speaker terminals.
• Zone3: Assign the surround back amplifier channels to supply Zone 3 speaker level outputs from
the surround back speaker terminals.
• Zone4: Assign the surround back amplifier channels to supply Zone 4 speaker level outputs from
the surround back speaker terminals.
TRIGGER SETUP
The T 785 features three configurable +12V DC Trigger Output that can be used to activate a
component or system it is fed into. A Trigger Input is also available to turn on the applicable link it is
associated to. Use a combination of [ ] or ENTER and [
] keys to navigate through the Trigger
Setup menu parameters.
TRIGGEROUT
Triggers are low voltage signals used to turn on/off other compliant devices. The T 785’s three +12V DC
Trigger Outputs (Trigger 1 Out, Trigger 2 Out and Trigger 3 Out) are dependent on which mode they
are associated with. There are six choices where +12V DC output can be assigned and these are – Main,
Zone 2, Zone 3, Zone 4, Zone 2+3+4 and Source Setup.
Main: +12V DC is available at the assigned Trigger Out when the T 785 is at powered state.
Zone2,Zone3,Zone4,Zone2+3+4: When the applicable Zone is at powered state, +1 2V DC
is available at the assigned Trigger Out.
SourceSetup: If Trigger Output is linked to “Source Setup”, +12V DC is available at Trigger Out
whenever the particularly assigned Source is selected. Please see also separate discussion about
“TRIGGER OUT” under the “SOURCE SETUP (NORMAL VIEW)” section.
DELAY
The availability of +12V DC at Trigger OUT can be regulated. If it is desired that +12V DC is available
without delay the moment Trigger OUT is linked to its assigned setting, set Delay to 0s. Otherwise, one
can select through a delay time of 1s to 15s.
AUTOTRIGGERIN
Auto Trigger IN allows external system controllers to toggle the associated section of the T 785 from
“Standby” to “On” and vice versa. When the TRIGGER switch at the rear panel is set to ON, a +12V DC
input at Trigger IN will power ON the section where Trigger IN is assigned,
Main: From standby mode, the T 785 is powered ON when +12V DC is applied at Trigger IN.
Zone 2, Zone 3, Zone 4: Applicable Zone is turned ON whenever +1 2V DC is present at Trigger IN.
All: Main, Zone 2, Zone 3 and Zone 4 as described above will all be activated given a +12V DC input at
Trigger IN.
WARNING
IfAutoTriggerINatTriggerSetupmenuisassignedto“Main”or“All”andtheTRIGGERswitchisset
to“AUTO”mode,thePowerbuttoninthefrontpanelaswellasthecorrespondingON/OFFfunction
keysintheHTRC1remotecontrolwillbedisabledeffectivelyhandingthisfunctiontoanexternal
controller.SwitchTRIGGERto“OFF”tomaintainnormalpowerON/OFFfunctionprocedures.
See also item “12. +12 V TRIGGER OUT, TRIGGER IN, TRIGGER AUTO/OFF” of REAR PANEL discussion as
well as the “TRIGGER OUT” discussion under “SOURCE SETUP (NORMAL VIEW)”.
OPERATION
USINGTHET785–SETUPMENU
5
EN
G
LI
SH
FR
ANÇ
AIS
ESP
AÑOL
IT
ALIANO
DEUT
SCH
NEDERL
ANDS
SVENSK
A
РУ
ССКИЙ