NAD VISO THREE Owner's Manual - page 15
CD-R AND CD-RW AUDIO DISCS
The VISO THREE can playback CD-R or CD-RW audio discs that have been
recorded on a computer or CD recorder. The quality of CD-R or CD-RW
audio discs varies widely which may affect playability. Some factors that
affect playability:
• The quality of the disc itself. Generally speaking, CD-R or CD-RW blanks
from well-renowned companies give better results than unbranded
ones.
• The quality of CD-recorder or computer CD re/writer. Some recorders
and writers produce better results than others.
• The CD-R and CD-RW were created with high-speed writing. In general,
the quality of a CD-R or CD-RW is better when produced at a lower
speed against a higher speed on the same recorder or re/writer.
PLAYING MP3/WMA FILES
The VISO THREE can play MP3/WMA formatted recordings on CD-R or CD-
RW discs. You may mix any of the file types on the disc. Refer to SELECTING
FOLDERS OR FILES (USB, CD-R/-RW) at the USB mode section below for
MP3/WMA playability procedure.
PROGRAMMING (CD/USB)
The program function enables you to store your favorite tracks from any
disc in the player memory. When programming a sequence of tracks, the
VISO THREE must be in STOP mode. Using the VR 3 remote control, enter
your desired program sequence through the following steps
1 Press [PROG]. The VFD will show
Program 1
T0000
The “0000” in the “T0000” keeps on blinking, meaning that the player is
awaiting the first Program entry.
2 Use the Direct-Entry numeric keypad buttons to enter the first track in
your planned sequence. For example, press “2” and then [ENTER]. The
VFD will briefly show
Program 1
T0002
3 The display will revert to show
Program 2
T0000
The “0000” in the “T0000” keeps on blinking, meaning that the player
is awaiting the second Program entry. For example, press “4” and then
[ENTER]. Upon entering the second track, the VFD will again briefly
show
Program 2
T0004
4 Repeat steps 2 and 3 to select and store other track numbers in
memory, up to a maximum of 32 entries. If you attempt to program
more than 32 tracks or files, “Program Full” will be displayed in the VFD.
Program Full
T0006
5 Press [PROG] to end or finalize the program – the VFD will show the last
programmed number and track.
6 Press [ ] (Play) to start program playback.
NOTES
• TheprocedureforprogrammingMP3/WMAfilesisthesameasabove.
• Ifyouwanttoselectfilenumber“119”inadiscwherethereare100or
moreMP3/WMAfiles,press“1”twiceandthen“9.”
• Pressing[STOP]buttonatanytimeduringtheprogrammingprocedure
willputtoaSTOPthesequenceandclearallthecurrentlyprogrammed
tracksorfiles.VFDwillrevertbacktodisplayingthetotalnumberof
tracksandtotalplaybacktimeforaudioCDandtotalnumberoffilesfor
MP3/WMA.
• Pressing[STOP]buttontwiceduringprogramplaybackwilldeletethe
wholeprogramlist.
REVIEW PROGRAM LIST
1 Initiate review of your programmed entries by pressing [PROG].
2 The VFD will show the first Program Number.
3 Press [ENTER] repeatedly to step through the program sequence. You
will have reached the end of the program sequence when “Program
End” is displayed at the VFD.
EDIT PROGRAM LIST
1 Initiate editing of your programmed entries by pressing [PROG].
2 The VFD will show the first Program Number.
3 Press [ENTER] repeatedly to step through the program sequence. Stop
at the program sequence you want to edit.
4 To change the programmed track of the particular sequence, use the
Direct-Entry numeric keypad buttons. Press [ENTER].
5 Press [PROG] to end or finalize the program.
DELETE PROGRAM
Initiate editing of your programmed entries by pressing [PROG].
1 To delete a particular programmed track/file, press repeatedly
[ENTER] key until the desired programmed sequence is reached. Press
VR 3’s [CLEAR] key once and the track/file in the particular sequence
is deleted. The program sequence will adjust accordingly as a
programmed track/file is deleted.
2 To clear the program memory, perform any of the following steps
• During programming mode, press [STOP] once.
• During program playback, press [STOP] twice.
• Press [OPEN/CLOSE] to open the disc tray (CD mode).
OPERATION
USING THE VISO THREE – CD MODE
15
EN
G
LI
SH
PO
R
TU
G
U
ÊS
FR
ANÇ
AIS
ESP
AÑOL
IT
ALIANO
DEUT
SCH
NEDERL
ANDS
SVENSK
A
РУ
ССКИЙ