NAD VISO TWO Owner's Manual - page 30
executing macroS
To execute a macro, press and release [MACRO]; its key illumination lights
for 5 seconds. While it remains lit, press an HTR 6 key to which a macro has
previously been stored.
The corresponding macro will run; as each step executes, its “parent” Device
Selector’s key flashes lights briefly; when execution is finished, the [MACRO]
key illumination goes out. Pressing any other HTR 6 key while a macro is
executing will abort the macro. Remember that you must hold the HTR 6 so
that its infrared emitter can activate the target components.
NOTE
Whenamacroexecutes,a1seconddelayisautomaticallyinserted
betweenitscommands.Ifyouneedmorethana1seconddelaybetween
particularcommands—forexample,topermitacomponenttopowerup
completely—youcanrecord“empty”stepsintothemacrobychanging
DeviceSelector“pages”withoutenteringactualcommandfunctions.
BUTTON ILLUMINATION TIMEOUT
The HTR 6’s key-illumination can be set to remain lit for 0-9 seconds. The
default value is 2 seconds. To set the illumination timeout, simultaneously
press-and-hold for 3 seconds both the HTR 6’s [DISP] and the [0-9] key, with
the digit corresponding to the desired timeout duration; the Learn LED will
flash twice to confirm the new setting. When set to zero, the illumination
will not turn on at all.
NOTE
KeyilluminationisthebiggestdrainontheHTR6’sbatteries.Ashort
key-illuminationtimeoutwillextendbatterylifeappreciably;turningit
offaltogether(setitto0seconds)willlengthenitstillfurther.
FACTORY RESET
The HTR 6 can be reset to its factory state, deleting all learned commands,
copied and punched-through keys, macros, and other setup information,
reverting all keys to their pre-programmed library commands.
To perform a factory reset simultaneously press-and-hold for 10 seconds
the HTR 6’s [ON] and [RTN] keys; the Learn LED will start to flash green.
Release [ON] and [RTN] before the second flash is complete; the Learn LED
will turn red, indicating the remote has been reset.
NOTE
Youmustrelease[ON]and[RTN]beforethesecondflashgoesout,otherwise
theunitwillnotreset;shouldthisoccur,repeatthefullprocedure.
DELETE MODE
The HTR 6 can store learned, copied, and “default library” commands on any
single key (The default library commands are the pre-programmed NAD
codes, such as the native VISO TWO commands on the [AMP] “page.”).
You can delete commands by layers back “down” to the default library
command on any key, removing learned commands, punched-through
functions, and copied keys.
NOTE
Thedefaultlibrarycommandscannotbedeleted,soyouneednotworry
thatusingDeleteModemightcauseirreparablechanges.
To enter Delete Mode, simultaneously press-and-hold for 3 seconds both
the desired key’s Device Selector key and the [RTN] key, until the Learn LED
turns green. Press the function key whose command you wish to delete;
the Learn LED flashes; the number of times indicates which type of function
has become active - see the table below. Press the active Device Selector
key again to exit Delete Mode.
NOTE
Youmaydeletemultiplefunction-keycommandsonthesameDevice
Selector“page,”buttodeletefrommorethanoneDeviceSelectorpage
youmustexitDeleteModeandthenre-enteritontherequiredpage.
Flashes
Command Type
1
Default Library Command
2
Copied Library Command
3
Learned Command
OPERATION
uSing the htr 6 remote control
0
EN
G
LIS
H
FR
A
N
Ç
A
IS
ES
PA
Ñ
O
L
IT
A
LIA
N
O
D
EU
TS
CH
N
ED
ER
LA
N
D
S
SV
EN
SK
A
РУ
СС
К
И
Й