1. DL manuals
  2. Nady Systems
  3. Microphone system
  4. UWS-1K Series
  5. Owner's Manual

Nady Systems UWS-1K Series Owner's Manual

Other manuals for UWS-1K Series: Owner's Manual
Manual is about: 1000 Channels PLL Frequency Synthesized UHF Wireless Microphone and Instrument System

Summary of UWS-1K Series

  • Page 1

    Owner’s manual uws-1k 1000 channels pll frequency synthesized uhf wireless microphone and instrument system.

  • Page 2

    Table of contents introduction 3 using this manual ......................................................................................................................3 system features ..................................................................................................................

  • Page 3

    Introduction thank you for choosing the nady uws-1k series wireless system, and congratulations on your choice. The nady uws-1k series systems are by far the best performance and price value in professional uhf wireless. They offer clear channel operation on the wide-open, uncluttered uhf band for i...

  • Page 4

    4 system operation 3. Uws-1k receiver buttons function each time the set button (19) is pressed the lcd menu (10) display will cycle through the set up menus in this order: main menu->channel->group->sql->main menu and then repeat. The selected function will flash for 20 seconds before returning to t...

  • Page 5

    5 6. Selecting the uh/ub-1k transmitters group & channel setting both the uh/ub-1k transmitters have to be programmed for the channel and group selected on the uws-1k receiver via the ir reception link between the receiver and transmitter during the first 20 seconds after the transmitter is powered u...

  • Page 6

    6 10. Adjusting the mute (rf squelch) the mute (rf squelch) (14) controls both the a and b receiver channels. This control ranges from 01 (low mute sensitivity level) to 50, (high mute sensitivity level). The control should be adjusted up to the highest reading at which the rf level meter (12) and t...

  • Page 7

    7 uws-1k receiver 1 2 3 4 5 6 7 16 8 9 15 10 18 20 1. Rack ears (optional) 2. Join pieces (optional) 3. Antennas 4. Rf screw-on connectors 5. Dc input jacks 6. Xlr balanced output 7. 1/4” unbalanced output 8. Power switch 9. Power led 10. Menu display 11. Group/channel 12. Rf level meter 13. Diversi...

  • Page 8

    8 uh-1k handheld microphone transmitter 13. Setting up the transmitter the uh-1k requires 2x aa size batteries to operate. To install the batteries onto the battery holder (21), unscrew the battery cover (22) by turning counter-clockwise and remove the cover, expos- ing the battery holder. Insert 2 ...

  • Page 9

    22 21. Battery holder 22. Battery cover 23. Power/mute button 24. Ir led sensor 25. Ir led indicator 26. Mute led 27. Battery level leds 28. Input level control 21 9 uh-1k’s power button to unmute. To mute, press the power/mute button again. Adjust the vol- ume of the receiver as per section 12 (uws...

  • Page 10

    10 ub-1k bodypack microphone transmitter back on). The battery level led (33) should stay fully lit green indicating usable battery strength. This led turns red if the batteries are low and the batteries should be replaced with new ones. To preserve battery life, turn the transmitter off when not in...

  • Page 11

    11 ub-1k bodypack microphone transmitter unmute the transmitter audio. Adjust the volume on the receiver for one-to-one, unity gain with a hardwired cord or select up to an added 4-5db boost by adjusting the receiver volume to maximum. (note: the input level control is deactivated and not used when ...

  • Page 12

    12 cautions and troubleshooting 23. Feedback observe care in selecting p.A. Volume, transmitter location and speaker placement so that the acoustic feedback (howling and screeching) will be avoided. Please also note the pickup pattern characteristics of the microphone selected. Omni directional mics...

  • Page 13

    13 tips • for optimum operation with external antennas, low loss rf shielded cable should be used and the length of the cable should not exceed 3m. • the receiver antennas should be kept away from any metal surfaces whenever possible as they can reflect or shield from the incoming rf signal. • if the...

  • Page 14

    14 specifications system specification operating frequency range ....................................................................760mhz-864mhz (3 bands) freq. Synthesized ................................................................... Pll system 1000 channels switchable 25khz/step, frequency...

  • Page 15

    Frequency plan band-1 748.900-773.875mhz 25khz per step (1000 channels) u.S. Band-2 795.000-820.000mhz 25khz per step (1000 channels) u.S./ europe band-3 846.000-871.000mhz 25khz per step (1000 channels) europe 15 accessories part number description rmk-1k single receiver rack mount kit rmk-1kx2 dua...

  • Page 16

    Nady systems, inc. 6701 shellmound street • emeryville, ca 94608 tel: 510.652.2411 • fax: 510.652.5075 • www.Nady.Com service information (u.S.) if you are experiencing operation problem with your system, check out the support page on the nady website: www.Nady.Com for help and for contacting the na...