O w n e r s m a n u a l c d p l a y e r s.
Page 1.0 equipment installation normally your naim equipment will have been installed by the dealer who sold it to you even if you live outside their immediate vicinity. Your dealer is responsible for making sure that the system sounds exactly as it should and information given here is not intended ...
2.0 getting started 2.1 switching on and off source components and power supplies for cd players, tuners, preamplifiers and crossovers should be switched on before switching on the amplifier(s). Always switch the amplifier(s) off and wait about a minute for its power supply capacitors to discharge b...
Important in order to comply with current european safety regulations it is essential that the naim loudspeaker connectors supplied with amplifiers and loudspeakers are used. Do not under any circumstances allow anyone to modify your naim equipment without first checking with the factory, your deale...
4.0 connection 4.1 mains lead as the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: the wire which is coloured green-and-yellow must be connected to the terminal in the plug which is ma...
5 c d s cds player operation there are six buttons on the right hand side of the cds player front panel. Press to activate. Several of these buttons operate differently depending on whether the player is in load condition (after a disc has been loaded, but before the play button has been pressed). T...
6 previous display next pause stop play track time repeat program mains input cds player (from serial no. 146541) xps power supply cable direction marker 5 to 5 pin din 11 to 11 pin burndy ch1 nc nc -ve ch 2 cds output interconnect cables to preamplifier cds player wiring.
7 cds player (from serial no. 146541) transit locks 1 open the door. Unlock the transit screws fully in the direction indicated. (remove and keep safe). Always lock these last before transit or shipping. 2.
8 place the compact disc on the platter. Make sure it is seated properly. Cds player operation cds player (from serial no. 146541) transit locks (continued) unlock the transit screws fully in the direction indicated. (remove and keep safe). Always lock these first before transit or shipping. 1 3.
9 2 3 4 place the disc clamp on the compact disc cds player (from serial no. 146541) cds player operation (continued) close the door press play.
C d x 10 cdx player operation there are four buttons situated on the right hand side of the front panel. Press to activate. Two of these buttons operate differently depending on whether the player is in load condition (before the play button has been pressed). The player returns automatically to loa...
11 previous next stop play pause time repeat program connection to optional xps power supply (for improved performance) mains input cdx player cable direction marker 5 to 5 pin din 11 to 11 pin burndy to preamplifier mains input power link plug fitted link plug removed ch1 nc nc -ve ch 2 cdx output ...
1 2 cdx player transit lock 1 remove the transit screw (keep safe). Always replace this before transit or shipping. Open the door. 1 cdx player operation.
Cdx player cdx player operation (continued) 2 3 4 5 place the compact disc on the platter. Make sure it is seated properly. Place the clamp on the compact disc. Close the door. Press play 1 3.
1 4 c d 5 cd5 player operation there are four buttons situated on the right hand side of the front panel. Press to activate. Three of these buttons operate differently depending on whether the player is in load condition (after the play button has been pressed). The player returns automatically to l...
1 5 cd5 player to preamplifier mains input power link plug removed mains input power to preamplifier mains input power link plug fitted ch1 nc nc -ve ch 2 cd5 output cable direction marker 180˚ 5 to5 pin 240˚ 5 to 5 pin din interconnect cables cd5 connection to flatcap 2 power supply pause time repe...
1 6 cd5 player transit locks 1 remove the transit screws (keep safe). Always replace this before transit or shipping. Open the door. 1 cd5 player operation.
2 3 4 5 place the compact disc on the platter. Make sure it is seated properly. Place the clamp on the compact disc. Close the door. Press play 1 7 cd5 player cd5 player operation (continued).
1 8 n 2 narcom 2 remote handset narcom 2 is a multi-functional remote control handset designed to be used with naim audio cd players, integrated amplifiers, pre-amplifiers and preset tuners. The handset control configuration is based around three types of keys: system component keys, global keys and...
1 9 3 soft keys these keys operate functions depending on the system component key setting. Numeric keypad: in preamp mode the numeric keys will switch between the amplifier inputs (1 - cd, 2 - tuner, 3 - tape, 4 - av, 5 - aux 1, 6 - aux 2). In cd mode the numeric keys will select tracks. In tuner m...
2 0 specifications cds frequency response 10hz-18khz ±0.1db - 0.5bd) output level 2.0v rms at 1khz output impedance 50 ohms nominal phase response linear, absolute phase correct de-emphasis ±0.1db referred to main response distortion & noise laser type semiconductor algaas wavelength 780nm mains sup...
21 naim audio southampton road salisbury england sp1 2ln tel: +44 (0)1722 332266 www.Naim-audio.Com owncd • issue 6 • may 2001 ec declaration of conformity to appropriate standards manufacturer naim audio limited southampton road salisbury england sp1 2ln products cds, cdx, & cd5 players xps and fla...