Summary of FLASH REMOTE HANDSET
Page 1
U p d a t e n o t e s issue 2 flash remote handset.
Page 3: Introduction
Introduction these update notes provide detailed operating instructions for the naim audio flash remote handset, software version rcc01-02. If you have received these notes as part of a software update pack you must first read appendix 1 – software update procedure and follow the instructions to upd...
Page 4: 2 Channel Mode
Mode ( setup ). To switch between 2ch and av modes press the navi key ( ) for a short time. To enter setup mode, press and hold the navi key ( ). 2 channel mode 2.
Page 5: Preamp Key (Pre)
2 channel mode is used to control 2 channel products such as preamps, cd players and tuners. Volume down ( 6 ), mute (mute) and volume up ( 5 ) hotkeys control preamp volume in this mode. Preamp key (pre) selects 1 of 2 preamp pages. Pre-s - numeric keys control preamp source selection. Pre-r - nume...
Page 6: Av Key (Av)
Av key (av) press and release to selects one of 3 av pages. Press and hold to send av standby command. Av-i/p - numeric keys control av processor input selection. Av-mode - numeric keys control av processor mode selection. Av - numeric keys are disabled. Dvd key (dvd) press and release to selects on...
Page 7
Adjust the current settings displayed on the right, and press ok ( ok ). Lights the lights setting controls the screen and button backlight. It has 4 settings: off – always off. On – on whenever the handset is awake. Auto – on whenever the handset is awake and the ambient light level is low (default...
Page 8: Softkeys
Softkeys the softkey setup menu allows alternate commands to be assigned to any of the 8 softkeys on each of the 13 pre- defined product pages. To assign a softkey , select the required product page using the ok ( ok ) key (press exit ( exit ) at any time to return to the instructions page). Then pr...
Page 9
Appendix 1 - software update procedure introduction this update to the flash remote handset provides the following enhanced features: • dvd and n-sub control functions • menu driven setup facility • user defined softkeys • new screen design with central command indication fully future-proof software...
Page 10
3. Note the orientation of the pic in the pic socket . There is a chamfer with a dot located on one side of the pic . The replacement pic must be inserted with the same orientation. 4. 5. 6. 7. 8. Attach an anti-static earth strap to your wrist and connect the crocodile clip to the top negative batt...
Page 11: Appendix 2 – Command Codes
Appendix 2 – command codes angle-d input-a disp-c (none) vol5-p subt-d spkr-a prog-c 5-a audio-d open-c vol6-p mem-d 1-c 6-a mute-p 1-d 2-c 4-a mon-p 2-d 3-c bal4-p 3-a 3-d 4-c 3bal-p i/p1-a 4-d 5-c i/p2-a disp-p 5-d 6-c i/p3-a prog-p 6-d 7-c i/p5-p i/p4-a 7-d 8-c i/p5-a i/p6-p 8-d 9-c i/p6-a 1-p 9-...
Page 12: Preamp
Appendix 3 – product commands use the following images to note changes to softkeys for future reference. Preamp default user cd default user 10
Page 13: Tuner
Tuner default user av default user 11.
Page 14: Dvd
Dvd default user subwoofer default user 12.
Page 16
Naim audio limited, southampton road, salisbury, england sp1 2ln telephone: +44 (0) 1722 332266 fax: +44 (0) 1722 412034 www.Naim-audio.Com part no. 12-001-0052 drawing no. Na906002-420/1.