超音波研磨装置 / ultrasonic polisher 取 扱 説 明 書 / operation manual om-k0517 001 目 次 1 . Cautions for handling and operation ･･･ p 16 2 . Specifications and dimensions ････ p 18 3 . Componant names ･･･････････････ p 18 4 . Preparation before use ････････ p 22 5 . Attachment of the tool ････････ p 23 6 . Oper...
16 thank you for purchasing the ultrasonic polisher sheenus neo. This product is designed for grinding, polishing, and mirror finishing on a wide range of materials from aluminum dies to cemented carbide dies. And has a wide variety of finishing tools such as diamond stone, diamond file, ceramic sto...
Grounding pin grounding pin metal screw (a) cover of ground outlet box (b) (c) (d) adapter grounding means ⑧ use proper extension cord. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An un...
18 2. Specifications and dimensions 2 - 1 control unit model ne240 oscillation frequency 22.5khz frequency control homing type output 45w max. (unclamp mode) 20w max. (clamp mode) power conditioning continuous variable type power source ac120v, 50 / 60hz ac230v, 50 / 60hz rating input 55va appropria...
19 2 - 2 handpiece model us-25pb oscillator pzt piezoelectric type cord length 2m weight 140g (excluding cord) standard accessories ・ power cord (2m)・・1pc. ・ wrench (10mm)・・2pc. ・ fuses for ac120v …t1.6ah 250v …2pcs. For ac230v …t1ah 250v …2pcs. ・ foot switch (fc-24)・・1pc. ・ allen wrench (2.5mm)・・1p...
20 ④ main power switch on / off main power source. The designation " i " indicates on. The designation " o " indicates off. ⑤ unclamp ( ) / clamp ( ) switch this switch will change the unclamp mode ( ) or clamp mode ( ). ・unclamp mode ( ) when using a one-piece tool, set to the unclamp mode ( ). ・cl...
21 3 - 3 rear of control unit fig. 3 ⑪ socket for foot switch connect the plug of foot switch ③. ⑫ inlet with power supply fuses insert the power cord here. Two fuses are possible (for ac120v : t1.6ah, for ac230v …t1ah 250v). Verify and use only the properly rated and type fuses. ⑫ inlet with power ...
22 4. Preparation before use (1) the test horn ⑭ comes with the handpiece ② . Remove the protector sleeve ⑬ and unscrew the test horn ⑭ using the two wrenches provided. Fig. 5 (2) insert the output plug of the hand-piece into the receptacle for connecting handpiece ⑩ to the control unit ① . Fig. 6 (...
23 5. Attachment of the tool 5 - 1 attachment of one-piece tools ⑯ , tip holders ⑮ and m4 screw joint adapter ⑰ attach the tip holders ⑮ or the m4 screw joint adapter ⑰ to the handpiece ② and clamp tightly using two provided wrenches. (fig. 9). Then reattach the protector sleeve ⑬ . Fig. 9 5 - 2 att...
24 6. Operating procedures (1) turn on the main power switch ④ and make sure the display ⑧ appears. (2) select unclamp / clamp mode using the unclamp / clamp switch ⑤ . The unclamp mode ( ) or clamp mode ( ) led will illuminate green. Caution ・ use clamp mode ( ) for the tip holders ⑮. ・ use clamp m...
25 (2) how to release the protection circuit resolve the problem that caused the protection circuit to activate. Release the protection circuit by taking the following actions. ・when operating by the on/off switch ⑥ . Toggle the on / off switch ⑥. The reset led (red) will be turned off and the prote...
26 9. Changing fuses warning ・ make sure to turn off the main power switch ④ and remove the power cord from the inlet with power supply fuses ⑫ before replacing the fuse. ・ use intended fuse only. Recommended fuses : ac120v : t1.6ah 250v ac230v : t1ah 250v (1) the inlet with power supply fuses ⑫ con...
27 10. How to set the control unit (1) changing watt display (0w display ⇒ 0.0w display) ・turn off the main power switch ④ . ・turn on the main power switch ④ while pressing the unclamp / clamp switch ⑤. ・the display ⑧ shows watt and 0.0 appears on the screen. ・turn off the main power switch ④ and th...
28 (1) mount the test horn ⑭ securely on the handpiece ②. (2) set the unclamp ( ) / clamp ( ) switch ⑤ to unclamp mode ( ), and the power control knob ⑨ to min. (3) put a drop of water on the test horn ⑭ (fig. 15). (4) turn on the output on / off switch ⑥, keeping the power control knob ⑨ at min. Ul...
29 problem item to be checked possible cause countermeasure not vibrate. Display ⑧ not light up. The plug of power cord is not inserted. Insert the plug of power cord. The main power switch ④ is off. Turn on the main power switch ④.. The power cord is broken. Replace the power cord. The main power s...
30 problem item to be checked possible cause countermeasure abnormal noise or sudden heat rise is generated. On led or reset led lights up. The tip holder ⑮ is used with unclamp mode ( ). Change the setting to clamp mode ( ). The tip holder does not match with the length of the tool. Adjust the tool...
31.
2013.07.20 003 י.
