Summary of Deep Silence 6 Revision B
Page 2
_______________________________________________________________ 02 ___________________________________________________________ 02 _____________________________________________________________ 02 ________________________________________________________________ 03 _____________________________________...
Page 3
I. Introducti on congratulati ons on the purchase of your new nanoxia deep silence 6 big-tower. We are confi dent that you will be delighted by your new pc case for many years to come. Nanoxia’s deep silence series have been designed and developed by an experienced team of developers in germany. The...
Page 4
If you are missing any of the items listed above, please contact our customer service immediately: support@nanoxia-world.Com (europe); support.Overseas@nanoxia-world.Com (international) features: - water cooling ready - special, lateral fastening points for a 360/280/240/140/120 mm radiator under th...
Page 5
Included are special rubber seals which can be used to alternatively close the tube holes above the rear chassis fan, in case you don’t need to use them. Another design element for optimum sound insulation is the use of two sound-insulated front doors. The doors are equipped with sound-absorbing foa...
Page 6
The innovati ve nanoxia acti ve air chimney makes it easy to adapt the case to your needs. Under extreme conditi ons you can counteract heat generati on under the top cover eff ecti vely: the two pre-installed fans under the cover will be automati cally enabled if the chimney is opened. Thus the war...
Page 7
Mounting bracket on the hdd cage: 280/240/140/120 mm radiator the mounting bracket between motherboard and hard drive cage is designed to make optimal use of the enormous size of the nanoxia deep silence 6 case for water cooling systems. The bracket can be used to install a 280/240/140/120 mm radiat...
Page 8
Ii. Installation instructions 1. Installing the motherboard you can mount hptx, e-atx, xl-atx, atx, m-atx and mini-itx motherboards in the deep silence 6. In order to ensure an easy installation of your motherboard, we suggest the following procedure: a) please consult the following charts to find y...
Page 9
D) next you should mount the cpu cooler - for very large cpu coolers, the att achment of the eps extension cable aft er installati on can be diffi cult. E) now place the motherboard gently inside the case and lead the eps extension cable through the opening provided in the top left of the mainboard ...
Page 10
3. Installati on of external drives you can install up to four external drives in the deep silence 6. Two adapter frames for mounti ng 3.5 inch drives are included. 3.1 opti cal drives to install the opti cal drives, please remove both side panels. The installati on of opti cal drives is tool-free. ...
Page 11
4. Installation options for hard drives the deep silence 6 allows you the decoupled mounting of 13 hard disk drives. By using the 5.25 inch to 3.5 adaptors, you can mount a total of 15 data storage disks in your case. 4.1 mounting of hard drives install the 2.5 or 3.5 inch hard drives in the illustr...
Page 12
4.2 uti lising the additi onal 3-bay hdd-cage the deep silence 6 is equipped with an additi onal 3-bay hdd-cage, which is screwed to the bott om of the case. If you wish, you can purchase additi onal cages at retailers and thus signifi cantly increase the hard disk capacity of the deep silence 6. Th...
Page 13
When you remove the top cover, proceed cautiously in order to not damage the cables of the i/o-panel and the active air chimney. To remove the cover completely, you need to remove the right side panel and disconnect the cable to the board that goes to the switch of the active air chimney (see drawin...
Page 14
You can remove the fan by pushing away the retaining lugs a little bit from the fan and then pull the fan out ( picture 6b ). The dust filters can easily be pulled out, as you can see here ( picture 6c ). Please note, that the filter elements must be fully inserted to guarantee the proper operati- o...
Page 15
6.3 fans in the mounti ng bracket behind the hdd cage if you want to mount additi onal fans inside the case, for example to opti mise disk venti lati on, you can use the specially developed mounti ng bracket that is screwed to the hard drive cage. For this, fi rst remove the screws and then take the...
Page 16
If you secure the cover in the side panel again aft er the removal of a side fan, please make sure not to ti ghten the screws not too much. To avoid damage to the internal thread or the side panel, the screws should be ti ghtened by hand only. 6.5 fans on the bott om of the case you can install two ...
Page 17
The controller has two channels (a and b), with each channel able to control up to four 3-pin fans, therefore a total of eight fans can be controlled. The fan controller is not designed for the operati on of powerful fans. Please take this into account in parti cular when using fans from other manuf...
Page 18
8. The active air chimney the innovative nanoxia active air chimney allows the easy dissipation of hot air in case of a heat buildup under the top cover: once the air chimney is opened, the connected fans are automatically activated. When the active air chimney is closed, the fans are switched off a...
Page 19
9. Installing a water cooling soluti on in the nanoxia deep silence 6, you can install both in the specially designed mounti ng bracket, as well as under the cover radiators or compact water cooling soluti ons. 9.1 installati on of a radiator or compact water cooling soluti on on the mounti ng brack...
Page 20
9.2 installati on of a radiator or compact water cooling under the top cover for the installati on of the radiator under the top cover, please use the off set mounti ng holes, as shown in the diagrams below. The off set ensures the best possible compati bility with current motherboards, even when us...
Page 21
10. The i/o-panel the i/o panel includes connectors for external usb devices (2 x usb 2.0, 4 x usb 3.0), and the microphone and headphone ports. The i/o panel can be retracted into the case when not in use, this helps to protect the connectors while maintain the clean looks of the deep silence 6. To...
Page 22
Pin assignment of the front panel usb cable plug connecting usb cables plug with internal usb port of the motherboard 11.2 usb 3.0 diagram 11c shows the typical pin assignment of the internal 19-pin usb 3.0. The pins are assigned in a way to fit on current motherboards ( diagram 11d ). By referring ...
Page 23
11.3 hd audio diagram 11e shows the pin assignment of the standard hd audio cable plug. The pins are assigned in a way to fit on current motherboards. By referring to the motherboard manual, please check that the hd audio port is identical to the one shown in diagram 11e . If the pin allocation of t...
Page 24
Iii. Support dear customer, the pc case you purchased has undergone a very thorough quality control. Nevertheless, should there be any unexpected problems with your case we ask that you first approach the dealer where you purchased the product. They are prepared to assist you with competent and unco...