1. DL manuals
  2. NAPCO
  3. Keypad
  4. Gemini GEM-P1632
  5. Installation Instructions Manual

NAPCO Gemini GEM-P1632 Installation Instructions Manual

Manual is about: CONTROL PANEL/COMMUNICATOR

Summary of Gemini GEM-P1632

  • Page 1

    R installation installation instructions instructions g e m - r p 3 d g t l digital keypad wi982a 6/99 © napco 1999 quick start: 1. Referring to the control panel wiring diagram, connect siren, aux. Power, pgm. Output, remote bus, earth ground, zone and telephone wiring. Note: see installation instr...

  • Page 2

    2.

  • Page 3

    Introduction the gem-rp3dgtl is a dual 7-segment digital keypad that is compatible with the napco gem-series gem-p816, p1632, p3200 & p9600 control-panels. Refer to user guide oi249 for operation instructions. While the gem-rp3dgtl may be used to fully program the control, the gem-rp1cae2 keypad pro...

  • Page 4

    Easy program mode overview entering the easy keypad program mode 1 enter the dealer security code (default = 456789) for a new panel or enter your custom dealer program code if programmed and press a 2 press no ( f ) repeatedly until function “ 17 “ (activate program mode) is displayed. Note: if you...

  • Page 5

    Total number of zones in area 1 (appears for new panel only) press the a button and then directly enter the total number of zones to be programmed for area 1. Valid entries are from 01 to 32. Directly enter the total number of zones, including leading zeros. Use number buttons 1 through 9 . Note: pr...

  • Page 6

    Entry/exit zones in area 1 (appears for new panel only) press the a button and then directly enter the zone number of any zones which are to be used as entry/exit zones. Valid entries are from 01 to 32. Di- rectly enter each zone number, including leading zeros. Use number buttons 0 through 9. Press...

  • Page 7

    7 central station receiver 1 format from the table below, enter the central station's receiver format. Use number buttons 1 through 9 . Note: press g0 for a zero and 0 for a blank space (•). Press g 1 through g 4 for letters b–e, respectively. Press j to save. Press next ( e ) button to proceed. Not...

  • Page 8

    Rf transmitter programming (for wireless systems only. Also see quick method, which follows) press the a button and for each transmitter (key fob transmitters also), then directly enter: 1 the zone number (01–32) to which the transmitter will be mapped, including leading zeros. 2 the 6-digit rf id #...

  • Page 9

    9 key fob transmitters keyfobs can be programmed as “arm/disarm” devices using the on and off buttons (refer to control panel installation instructions). Press the a button and for each key fob transmitter, enter: 1 the key fob transmitter number (01–15). 2 the area number to which transmitter is as...

  • Page 10

    Total number of zones and keypads in area 1. Total number of zones and keypads in area 2. (appears for new panel only) 1 press the a button and then press 3 to select the total number of zones to be programmed for area 1. Valid entries are from 08 to 24 in multiples of 4. 2 press 2 and press 3 to se...

  • Page 11

    11 central station receiver 1 format from the table below, enter the central station's receiver format. Use number buttons 1 through 9 . Note: press g0 for a zero and 0 for a blank space (•). Press g 1 through g 4 for letters b–e, respectively. Press j to save. Press next ( e ) button to proceed. No...

  • Page 12

    12 rf transmitter programming (for wireless systems only. Also see quick method, which follows) press the a button and for each transmitter and directly enter: 1 the zone number (01–96) to which the transmitter will be mapped, including leading zeros. 2 the 6-digit rf id # printed on the transmitter...

  • Page 13

    Key fob transmitters keyfobs can be programmed as “arm/disarm” devices using the on and off buttons (refer to control panel installation instructions). Press the a button and for each key fob transmitter, enter: 1 the key fob transmitter number (01–15). 2 the area number to which transmitter is assi...

  • Page 14

    Direct address program mode this is an extension of the dealer program mode. This method of programming is used in conjunction with the keypad programming worksheets contained in the control panel programming guide. Refer to these worksheets to identify the 4-digit location (address) of the feature ...

  • Page 15

    15.

  • Page 16

    Napco security systems, inc. (napco) war- rants its products to be free from manufacturing defects in materials and workmanship for thirty-six months fol- lowing the date of manufacture. Napco will, within said period, at its option, repair or replace any product failing to operate correctly without...