1. DL manuals
  2. NEC
  3. Laptop
  4. VersaPro VB VC26M/BC-F
  5. User Manual

NEC VersaPro VB VC26M/BC-F User Manual

Summary of VersaPro VB VC26M/BC-F

  • Page 1

    User's guide vb model checking included accessories .............................................2 connecting included accessories ..........................................2 windows setup ......................................................................3 knowing the parts ........................

  • Page 2

    2 checking included accessories please open up the box and check that all included items and accessories are there. Please immediately contact the place of purchase if any items happen to be missing or damaged. 1. Check contents of the box. *1 : included with model vc26m/bc-f *2 : included with mode...

  • Page 3

    3 windows setup when you first power up your new computer, it is necessary to perform windows setup. • always follow the procedure written in the manual. Setup may not be able to be successfully completed if you omit any steps, press any keys other than the ones indicated on the screen, or operate a...

  • Page 4

    4 3 enter a user account password when prompted and click [next] to continue. 4 please check the contents when the [please read the license terms] page is displayed. 5 after checking the contents, check [i accept the license terms] and click [next] to continue. 6 when the [help protect your computer...

  • Page 5

    5 as a default setting, the first internal hard disk has only one useable partition (volume), designated as the c: drive. However, it is possible to divide the c: drive into multiple partitions. Please refer to the following steps if you would like to change the factory default settings and reduce t...

  • Page 6

    6 knowing the parts  the front and right sides  the back and left sides  the bottom  explanation of components names and descriptions of your computer's major components 4 (1) (2) (3) (4) (5) (7) (8) (9) (10) (12) (24) (29) (25) (26) (23) (14) (20) (21) (13) (25) (11) (28) (19) (15) (22) (27) (6...

  • Page 7

    7  power led *1 : flashes about once every three seconds. *2 : flashes about once every two seconds.  battery recharge led *1 : battery recharging error, battery life, or deterioration error. *2 : when the battery is fully charged, or nearly fully charged, there are some cases where the led does n...

  • Page 8

    8  caps lock indicator led  scroll lock indicator led battery battery pack removal please remove the battery pack according to the following illustration. Battery pack installation please install the battery pack according to the following illustration. Led state computer state on (green) is on (a...

  • Page 9

    9 keyboard by pressing the function key in combination with another key, you can easily change common computer settings. These functions are called "hotkeys". *1 : this setting is canceled when the computer power is turned off or restarted. The nx pad this section covers the nx pad usage and extende...

  • Page 10

    10 configuration of the nx pad buttons, pointer behavior, and extended features is done using the [mouse properties] window. 1 click [start] and then [control panel]. 2 click [hardware and sound], and click [mouse] in [devices and printers]. The [mouse properties] window should come up. Click on eac...

  • Page 11

    11 please refer to the following procedure to change the screen resolution with the keyboard. 1 press + and set the screen output to clone mode. 2 after clone mode has been set, press + again. The icons to change the resolution are displayed under the screen output icons. 3 press + , and select the ...

  • Page 12

    12 the following steps can be used to configure your computer to allow wol from when the power is turned off. 1 turn the power on and immediately press several times. The bios setup utility will then be displayed. 2 in the [advanced] menu, set [remote power on] to [enabled]. 3 press the key. 4 confi...

  • Page 13

    13 the following explanation is for connecting to a wireless lan access point that broadcasts its network name (ssid). For information about other connection methods, please refer to windows help. 1 confirm that your computer's wireless lan function is turned on. 2 go to the [control panel] and clic...

  • Page 14

    14 proset/wireless can be uninstalled with the following steps. 1 start windows. 2 click [start] and then [all programs]  [accessories]  [run]. 3 enter the following in the [open] dialog and then click [ok]. C:\drv\wlinsev\utility\apps\setup.Exe /qn/x/forcerestart note:  represents a single-by...

  • Page 15

    15 4 return the memory slot cover to its original position and reinsert the screws into the bottom of the unit. Your new memory should now be ready to use. System configuration 1 turn the power on and immediately press several times. The bios setup utility will then be displayed. The bios setup util...

  • Page 16

    16 please follow these steps to restore your system to the default factory settings. 1 enter the bios setup utility. 2 press the key. A confirmation screen should be displayed. Press the button to cancel and exit. 3 confirm that [yes] is selected and then press . This will load the default factory s...

  • Page 17

    17 1 enter the bios setup utility. 2 under [intel feature configuration] in the [advanced] menu, set [intel(r) me bios extension] to [enabled]. 3 set [unconfigure me] to [enabled]. 4 press the key. A confirmation screen should be displayed. 5 confirm that [yes] is selected and then press . These set...

  • Page 18

    18 7 if a confirmation screen is displayed after the computer restarts, press . The settings are saved and the computer restarts. The features of the security chip are now enabled. Applications "microsoft ® office trial" is pre-installed in this product. To use microsoft ® office, you need to purcha...

  • Page 19

    19 go to the [control panel], click [programs]  [uninstall a program], then select [battery tool] and click [uninstall]. Follow the instructions on the screen for the procedure. When reinstalling the uninstalled [battery tool], perform the following steps. 1 insert the "application disc" into the o...

  • Page 20

    20 1 turn on the computer. 2 if the power lamp lights, quickly insert the "recovery disc" into the optical drive. 3 when [press any key to boot from cd or dvd...] is displayed, press . 4 when the [windows recovery] screen is displayed, select [erase data on the hard disk], and press . 5 when [data o...

  • Page 21

    21 recovery here we will explain the basics before recovery. Please read this before performing recovery. When recovering from a dvd, the following materials are required. Prepare all of the materials before starting the process. • recovery disc before recovery, if there is data that you would like ...

  • Page 22

    22 when recovery cannot be performed if [the computer can not be restored.] is displayed, it is possible that model information was written incorrectly. Please contact our repair facilities. Do not leave the computer alone during recovery do not leave the computer unattended until the recovery has c...

  • Page 23

    23 after recovery the applications which you installed from application disc or by any other way can not be recovered. Reinstall them if needed. That is all for windows 7 recovery. Appendix for comments, please refer to the followings. Comments * 2 : supports hyper-threading technology. * 6 : protru...

  • Page 24

    (1) unauthorized copying of all or part of the contents of this manual is prohibited. (2) the contents of this manual may change without notice. (3) the contents of this manual have been created with full efforts, if there are any errors, queries, or omissions please contact the vendor or our 121 co...