10 in. Meat saw/grinder with 3/4 horsepower motor owner's manual item # 168650 warning: read carefully and understand all instructions before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. 0110
1 thank you very much for choosing a northern tool + equipment co., inc. Product! For future reference, please complete the owner's record below: model: _______________ purchase date: _______________ save the receipt, warranty and these instructions. It is important that you read the entire manual t...
2 electrical safety warning! Always check to ensure the power supply corresponds to the voltage on the rating plate. • do not abuse the cord. Do not yank tool or extension cords from the receptacle. Keep power and extension cords away from heat, oil, sharp edges or moving parts. Replace damaged cord...
3 • never place your fingers in a position where they could contact the saw if the workpiece should unexpectedly shift or your hand should slip. • never climb on or allow others to climb on the saw table; it could break or pull the entire unit down. • turn the motor switch off and put away the switc...
4 getting to know your meat saw/grinder 1. Cover 2. Blade guard 3. Fence 4. Pusher 5. Pusher locking knob 6. Sliding stainless steel table 7. Front access door 8. Front motor access panel 9. Rubber feet 10. Steel stand 11. Meat grinder assembly locking handle 12. Tube connector 13. Meat grinder inta...
5 once the base is assembled, attach the drive belt (part # 55) to the motor wheel (a) and to the spindle wheel (b) in the compartment directly above. If the two wheels don’t line up properly, loosen the four bolts (c) holding the motor in place and slide the motor up or down, depending on need. Onc...
E 6 replacing or adjusting the saw blade warning ! Make sure the machine is unplugged from a power source before replacing or adjusting the saw blade. To prevent serious injury, wear heavy-duty work gloves when working with or around the saw blade. Removing the table before attempting to remove or r...
7 mounting a new blade use only authorized replacement blades. To mount a new blade, begin by placing the upper portion of the blade onto the upper drive wheel, teeth facing down and toward you. While doing this, insert the blade in the slot located on the upper guide body (n). (figure 8) mount the ...
8 assembling the power switch warning! Do not use sharp tools when assembling the power switch, as they may damage the insulation on the wires. If you are unfamiliar with electrical work, contact a professional electrician to perform the installation. The on/off power switch (w) is located in the up...
9 mounting a new blade the fence (cc) and pusher (dd) have predetermined spaces for attachment to the table. The fence attaches to the side, the pusher attaches to the end. Using socket screws, attach the fence and pusher to their respective areas. (figure 16) operation before and after use, wash al...
10 meat grinder use warning! Before using the meat grinder, clean all the working parts with hot soapy water. Do not attempt to grind bones or frozen meat as they may damage the grinder. Do not use fingers, utensils or anything other than the push rod to press meat into the intake. Attach the meat g...
11 1 fence 1 2 screw m6x16 6 1 r a b 3 4 fix bracket 2 5 knob 2 6 working table 1 7 fence 1 1 r a b 8 9 retaining ring 1 10 bearing 2 11 saw blade 1 12 wheel 1 13 retaining ring 1 14 bearing 1 15 cover 1 16 nut m10 1 17 flat washer ø10 1 18 spring 1 19 elavating plate 1 20 adjusting plate 1 21 conne...
12.
Northern tool + equipment co., 2800 southcross drive west p.O. Box 1499 burnsville, mn 55337-0499 made in china warranty one-year limited warranty.
