NOTHERN TVIBIR65 Installation & Setup Manual

TVIBIR65

HD-TVI Full HD 1080p Outdoor 65’ IR Bullet

Rev. 102115

3625 Cincinnati Avenue, Rocklin, CA 95765  

i

  855-388-7422  

i

  www.northernvideo.com

 Installation & Quick Setup Guide

Regulatory Information

FCC Information

FCC compliance: This equipment has been

tested and found to comply with the limits for a

digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide 

reasonable protection against harmful

interference when the equipment is operated in 

a commercial environment. This equipment

generates, uses, and can radiate radio 

frequency energy and, if not installed and used

in accordance with the instruction manual, may 

cause harmful interference to radio 

communications. Operation of this equipment in 

a residential area is likely to cause harmful 

interference in which case the user will be 

required to correct the interference at his own 

expense.

 FCC Conditions

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two 

conditions:

1. This device may not cause harmful

    interference.

2. This device must accept any interference 

    received, including interference that may

    cause undesired operation.

EU Conformity Statement

upon the purchase of equivalent new equipment,

or dispose of it at designated collection points.

For more information see: 

www.recyclethis.info.

2006/66/EC (battery directive):

This product contains a battery that 

cannot be disposed of as unsorted

 municipal waste in the European 

Union.

See the product documentation for specific

battery information. The battery is marked with 

this symbol, which may include lettering to 

indicate cadmium (Cd), lead (Pb), or mercury (Hg). 

For proper recycling, return the battery to your 

supplier or to a designated collection point. For 

more information see: www.recyclethis.info. 

2012/19/EU (WEEE directive):

Products marked with this symbol 

cannot be disposed of as unsorted 

municipal waste in the European

Union. For proper recycling, return

this product to your local supplier 

This product and - if applicable - the 

supplied accessories too are marked 

with "CE" and comply therefore with 

the applicable harmonized European

standards listed under the Low Voltage Directive 

2006/95/EC, the

 EMC Directive 2004/108/EC,

the RoHS

 Directive 2011/65/EU.

This series of camera adopts new generation 

sensor with high sensitivity and advanced circuit 

design technology. It features high resolution, 

low image distortion and low noise, etc., which 

makes it suitable for surveillance system and 

image processing system.

High performance CMOS sensor and high 

   resolution bring high-quality image;

Low illumination;

OSD menu, parameters are configurable;

Support auto white balance, auto gain control, 

   electronic shutter control;

Support image effect adjustment; 

Unit transmission control; 

Advanced 3-axis design meets different 

   installation requirements.

1  Introduction

1.1  Product Features

1.2 Overview

1.2.1 Overview of Type I Camera

2 Installation

Before

you

start

:

Please make sure that the device in the package 

   is in good condition and all the assembly parts 

   are included.

Make sure that all the related equipment is 

   power-off during the installation.

Check the specification of the products for the 

   installation environment.

Check whether the power supply is matched 

   with your power output to avoid damage.

Please make sure the wall is strong enough to 

   withstand three times the weight of the camera

   and the mounting.

If the wall is the cement wall, you need to insert

   expansion screws before you install the camera.

   If the wall is the wooden wall, you can use 

   self-tapping screw to secure the camera.

If the product does not function properly, 

   please contact your dealer or the nearest 

   service center. Do not disassemble the camera

   for repair or maintenance by yourself.

Steps:

1. Drill the screw holes  in the ceiling according 

    to the supplied drill template.

2. Hammer the supplied plastic expansion bolt into

    the screw holes.

2.1 Wall & Ceiling Mounting

Figure 2-1  Drill Template

3. Route the cables to the cable hole and connect 

    the corresponding power cable and video cable.

4. Fix the camera to the ceiling with the supplied screws.

ScrewHole

ScrewHole

ScrewHole

HD Video Cable

Power Cable

Mounting Base

Sun Shield

Lens

IR LED

960H Video Cable

5. Adjust the surveillance angle. 

1). Loosen No.3 adjusting ring to adjust the 

     panning position 

(0° ~ 360°).

2). Tighten No.3 adjusting ring.

3). Loosen the No.2 adjusting screw to adjust the 

     tilting position 

(0° ~ 90°).

4). Tighten No.2 adjusting screw.

5). Loosen No.1 adjusting screw to adjust the

     azimuth angle of the image 

(0° ~ 360°).

6). Tighten No.1 adjusting screw.

Figure 2-3 3-axis Adjustment

Figure 2-2 Fix the Camera to the Ceiling or Wall

Wall

Ceiling

360°

90°

360°

1

2

3

Thank you for purchasing our product. If there

are any questions, or requests, please do not

hesitate to contact us.

This manual may contain several technical

incorrect places or printing errors, and the

content is subject to change without notice.

The updates will be added to the new version of

this manual. We will readily improve or update

the products or procedures described in the

manual.

Privacy Notice

Surveillance laws vary by jurisdiction. Check all

relevant laws in your jurisdiction before using

this product for surveillance purposes to ensure

that your use of this product conforms.

Please refer to the product  specification for

camera parameters and functions.