Nova U12 Manual - 4.1. Connection Panel
4.1. Connection Panel
4.1. Anschluss- / Bedienfeld
DSP Program Selector
Selector, to load DSP programs (1-6).
Power / Limit LED Indicator
Lights green, if the unit is switched ON.
The LED is blinking for 4 seconds after switch-on
(indicates „Initializing DSP and built-in amplifiers).
Lights yellow, if the internal limiter is active.
The limiter will operate if:
- output voltage of the amplifier has exceeded the maximum value
- if excessive integral power consumption is detected
- if the amplifier overheats
The LED is blinking if the internal DSP is connected
to the UNION PC software (online mode).
LEVEL Controller
Adjusts the level of the input signal.
Reduces the level in case of signal distortion.
USB Connector
USB socket, for data transfer to a computer (PC).
USB LED Indicator
The LED lights green, if an USB cable is connected
to the USB socket (at the unit) and the PC.
INPUT Connector
Symmetric XLR female connector for signal input.
LINK Connector
Symmetric XLR male connector (linked parallel
to input connector).
AUX Connector
Symmetric XLR male output connector
(signal routed from DSP AUX-channel).
Mains Input Connector
Mains (NEUTRIK PowerCon©) input connector,
for power mains cable with locking function.
Mains Output Connector
Mains (NEUTRIK PowerCon©) output connector,
to link the input power from mains.
Mains Switch
Used for switch ON or OFF the speaker.
DSP Programm-Selektor
Drehregler, um ein DSP Programm zu wählen / laden (1-6).
Power / Limit LED Anzeige
Leuchtet grün, wenn das Gerät eingeschaltet ist (ON).
Die LED blinkt für 4 Sekunden nach dem Einschaltvorgang
(zeigt an, dass der interne DSP und die Verstärker initialisiert werden).
Leuchtet gelb, wenn der interne Limiter aktiv ist.
Der Limiter ist in folgenden Situationen aktiv:
- Wenn die Ausgangsspannung den Maximalpegel überschritten hat
- Wenn ein übermäßiger integraler Stromverbrauch erkannt wird
- Wenn sich der Verstärker überhitzt
Die LED blinkt dauerhaft bei einer Verbindung zwischen dem internen
DSP und der UNION PC Programmiersoftware (Online Modus).
LEVEL Regler
Stellt den Pegel des Eingangs INPUT ein. Drehen Sie diesen
Regler zurück, wenn das Signal verzerrt klingt.
USB Anschlussbuchse
Zum Anschluss eines USB-Kabels für den Datenverkehr zu einem PC.
USB LED Anzeige
Leuchtet grün, wenn ein USB-Kabel am Gerät und einem
eingeschalteten PC angeschlossen ist.
INPUT Anschlussbuchse
Symmetrische XLR Signal-Eingangsbuchse (female).
LINK Anschlussbuchse
Symmetrische XLR Signal-Ausgangsbuchse (male), ist der
INPUT Eingangsbuchse parallel geschaltet.
AUX Anschlussbuchse
Symmetrische XLR Ausgangsbuchse (male), Signalausgang
des DSP AUX-Kanals.
Netz-Anschlussbuchse (Eingang)
Netzbuchse zum Anschluss des verriegelbaren
Netzkabels (NEUTRIK PowerCon©).
Netz-Anschlussbuchse (Ausgang)
Netzausgangsbuchse zum Anschluss eines optionalen,
verriegelbaren Netzkabels (NEUTRIK PowerCon©).
Netzschalter
Hauptschalter zum Ein- und Ausschalten des Lautsprechersystems.
1
1
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
2
2
3
3
13
4. Connection Panel & Features (Self-Powered Types)
Anschlüsse & Bedienelemente (Aktive Modelle)
12
2
3
9
1
Panel U12A / U15A
4
5
6
8
10
11
7