OAKWORKS Antigua Instruction Manual - page 11
3
PRODUCT DESCRIPTION
•
Antigua™
PRODUCT DESCRIPTION
TA B L E S P E C S * :
• Height *:
25" - 35"
• Width:
31"
• Length:
72"
• Lift Capacity:
625 lbs Maximum Working Load
• Weight:
200 lbs.
• Top:
Electronically Controlled Flex Top
Round Corner Flat Top
• Electronics:
1 Hand Control & 1 Foot Control
• Padding:
Aero·Cel
™
System
• Upholstery:
Ultratouch II or TerraTouch
™
• Cabinetry:
Wood/ Maple
For electrical specs, see Specifications Chart, pg 18.
* measurements are determined from floor to top of seat pad using
standard padding; these measurements can be affected by natural
material variations in padding
** published weight may differ due to options chosen, natural
material variations and padding density
Antigua
™
-
Model ANRCMP
Model ANF3MP
Self Adjusting
Removable
Ar m Rests (2)
(optional)
Hand
Control (1)
Sliding Cabinet
doors / 2
(access both
sides)
Upholstered
Top
QuickLock
™
Face Rest
(optional)
Back Rest
Fully Enclosed
Cabinet Base
- Maple
Accessory
Outlets (2)
Foot Control (1)
Vertical
Hydraulic
Lift Columns (4)
Leg Rest
Seat
PRODUCT
DESCRIPTION
• Moving the
Antigua
™
The optional stationary Table Extender provides ultimate comfort for
your tallest clients, quickly and easily. The Table Extender comes with
two connecting arms that slide into the outlets at the foot end of the
tabletop. Slide these fully into the outlets so the Table Extender is flush
to the end of the table top. This Stationary Extender provides 11" of
additional comfort and support when needed.
The
Antigua
™
weighs approximately 200 lbs. You will need 4 people
working together if it is necessary to move the table. Never lift the table by
grasping the table top as the table top is not designed to hold the weight
of the base and you could damage the table and the electronics that run
the tabletop.
If you need to move the table, place one person at each corner of the
table. We recommend that you have the table top in a flex position(with
Arm Rests removed) to have the table top ends out of the way as much
a possible. Have each person firmly grasp the cabinet base at the bottom
by the table legs and lift the table from the base. As when moving any
piece of heavy equipment, bend at the knee and lift with your legs
beneath you and not with your back. Be aware and use proper, safe
procedures for moving a table of this size to prevent injury to yourself
or the table. We strongly recommend that a flatbed dolly be used that
can hold the entire table if moving the table involves any distance.
• Accessory Option:
Table Extender
CAUTION
Before moving the
Antigua
™
,
disconnect the power cord
from the power outlet and
secure the electrical cord,
hand control and foot con-
trols for moving.
DIRECTIONS FOR USE
Be sure to read all
cautions, warnings
and instructions given
in the manual to prevent
injury to both operator
and client.
CAUTION
The table weighs as much
as 200 lbs. DO NOT lift or
move the unit without using
proper safety procedures
or equipment. DO NOT turn
the
Antigua
™
on its side for
any reason. To do so could
cause damage to the base
and will void the warranty.
There are no serviceable
items that require this action
.
Never lift the table by grasp-
ing the table top as the
table top is not designed to
hold the weight of the base
and you could damage the
table.
Outlets
M
O V I N G T H E
Antigua
™
:
Position 8 at low height range
Grasp
at base
corner
CAUTION
Do not put excessive weight
or pressure on the extender.
Excessive pressure can cause
premature failure of the Table
Extender.
14
ACCESSORY OPTIONS
• Accessory Option: Table Extender
• Moving the
Antigua
™
ACCESSOR
Y OPTIONS