1. DL manuals
  2. Oce
  3. Printer
  4. TDS100
  5. User Manual

Oce TDS100 User Manual

Other manuals for TDS100: Quick Reference Manual

Summary of TDS100

  • Page 1

    Océ tds100 user manual.

  • Page 2: Océ-Technologies B.V.

    Copyright © 2005, océ-technologies b.V. Venlo, the netherlands all rights reserved. No part of this work may be reproduced, copied, adapted, or transmitted in any form or by any means without written permission from océ. Océ-technologies b.V. Makes no representation or warranties with respect to the...

  • Page 3

    3 trademarks products in this manual are referred to by their trade names. In most, if not all cases, these designations are claimed as trademarks or registered trademarks of their respective companies. Notes for the reader introduction this manual helps you to use the océ tds100. The manual contain...

  • Page 4

    4 user manual.

  • Page 5

    Contents 5 contents notes for the reader 3 chapter 1 introduction to the océ tds100 the documentation set 8 the configurations 9 the components 10 the operator panel of the automatic 1 roll and 2 roll feed configuration 12 the operator panel of the sheet feed, multi copy configuration 17 the operato...

  • Page 6

    6 user manual appendix b miscellaneous 61 reader's comment sheet 62 addresses of local océ organisations 64.

  • Page 7

    7 océ tds100 user manual chapter 1 introduction to the océ tds100

  • Page 8

    8 user manual the documentation set introduction this manual is a part of a documentation set. The following table displays the complete list. Overview of the complete documentation set note: visit océ on the internet at www.Oce.Com for more information. Document publication medium contents safety m...

  • Page 9

    Introduction to the océ tds100 9 the configurations introduction the océ tds100 is a wide format copier to copy large drawings. The océ tds100 is available in four different configurations. The following table displays these configurations with their functions and options. Functions and options per ...

  • Page 10

    10 user manual the components introduction the following illustration displays the most complete configuration of the océ tds100, the automatic 2 roll feed configuration. Some options may not be available on your tds100 due to the differences between the configurations. Illustration [1] the automati...

  • Page 11

    Introduction to the océ tds100 11 the components and functions of the océ tds100 note: some items may not be available on your océ tds100 due to the differences between the configurations. Nr. Component function 1 on / off switch turn on and off the océ tds100. Note: the on / off switch is not visib...

  • Page 12

    12 user manual the operator panel of the automatic 1 roll and 2 roll feed configuration introduction you can identify your configuration by its operator panel. The following illustration displays the operator panel of the 1 roll and 2 roll configuration..

  • Page 13

    Introduction to the océ tds100 13 illustration [2] the operator panel of the automatic 1 roll feed and 2 roll feed configuration [2] the operator panel of the automatic 1 roll feed and 2 roll feed configuration 4 2 0 -2 -4 media paper roll 1 trailing synchro film roll 2 leading standard feed manual ...

  • Page 14

    14 user manual the indicators nr. Indicator function 1 'toner' indicate that the océ tds100 has run out of toner. 2 green light indicate that the copier is ready. A blinking green light indicates that the copier runs a copy job. 3 red light indicate that an error has occurred. 4 'media jam' ■ indica...

  • Page 15

    Introduction to the océ tds100 15 the keys and their functions nr. Key function 6 'media' select the media type of the copy. Select one of the following. ■ 'paper' ■ 'film' 7 'feed' select the media feed method. Select one of the following. ■ 'roll 1' ■ 'roll 2' (2 roll configuration only) ■ 'manual...

  • Page 16

    16 user manual 12 copies adjust the number of copies. You can select a number of copies from 1 up to 9. 13 stop ■ when you press the stop key while the copier runs a copy job, the copy job will stop. ■ when you press the stop key once while you set up a copy job, the number of copies returns to 1. ■...

  • Page 17

    Introduction to the océ tds100 17 the operator panel of the sheet feed, multi copy configuration introduction you can identify your configuration by its operator panel. The following illustration displays the operator panel of the multi copy configuration. Illustration [3] the operator panel of the ...

  • Page 18

    18 user manual the indicators nr. Indicator function 1 'toner' indicate that the océ tds100 has run out of toner. 2 green light indicate that the copier is ready. A blinking green light indicates that the copier runs a copy job. 3 red light indicate that an error has occurred. 4 'media jam' ■ indica...

  • Page 19

    Introduction to the océ tds100 19 the keys nr. Key function 6 'media' select the media type of the copy. Select one of the following. ■ 'paper' ■ 'film' 7 exposure adjust the exposure. Use the exposure setting to correct the background of the copy. You can adjust the exposure from -4 up to +4. A neg...

  • Page 20

    20 user manual the operator panel of the sheet feed, single copy configuration introduction you can identify your configuration by its operator panel. The following illustration displays the operator panel of the single copy configuration. Illustration [4] the operator panel of the sheet feed, singl...

  • Page 21

    Introduction to the océ tds100 21 the indicators the keys nr. Indicator function 1 'toner' indicate that the océ tds100 has run out of toner. 2 green light indicate that the copier is ready. A blinking green light indicates that the copier runs a copy job. 3 red light indicate that an error has occu...

  • Page 22

    22 user manual.

  • Page 23

    23 océ tds100 user manual chapter 2 use the océ tds100

  • Page 24

    24 user manual turn on and off the océ tds100 introduction when you turn on the océ tds100, you can use the océ tds100 immediately. After you finished your copy job, you can leave the océ tds100 on, because the océ tds100 turns into the sleep mode within two minutes. The power use is very low in the...

  • Page 25

    Use the océ tds100 25 how to turn off the océ tds100 1. Set the on / off switch at the back of the océ tds100 to position 0. Result the green light of the on / off switch is off and the green light at the operator panel is off..

  • Page 26

    26 user manual turn on and off the optional dew preventer introduction you are advised to use the optional dew preventer in an extreme humid environment to improve the copy quality in this condition. Illustration [6] the on / off switch of the dew preventer [6] the on / off switch of the dew prevent...

  • Page 27

    Use the océ tds100 27 copy on a media roll (automatic roll feed) introduction you can make the copies automatically on the 1 roll and 2 roll configuration. The main steps of every automatic copy-job are the following. 1. Feed the original 2. Set up your copy job at the operator panel 3. Press the gr...

  • Page 28

    28 user manual 2. Set up your copy job at the operator panel ■ use the 'media' key to select the media type to copy on. When you press the media key, one of the following situations occur. - the selected media and corresponding roll illuminates. The operator panel displays the size of the media roll...

  • Page 29

    Use the océ tds100 29 copy on cut sheet media (manual sheet feed) introduction you can make the copies manually on all configurations. The main steps of every manual copy-job are the following. 1. Feed the original 2. Feed the cut sheet 3. Set up your copy job at the operator panel 4. Press the gree...

  • Page 30

    30 user manual 2. Place the cut sheet media centrally and face up on manual feed table [9] feed the cut sheet media centrally [9] feed the cut sheet media centrally the operator panel illuminates 'manual' and displays the length of the original. 3. Set up your copy job at the operator panel ■ use th...

  • Page 31

    Use the océ tds100 31 adjust leading and trailing strips introduction both originals and copies can contain a strip to file it. The océ tds100 allows you to handle strips as follows. ■ remove a strip ■ add a strip. You can adjust the following strips. ■ leading strip. A leading strip is at the begin...

  • Page 32

    32 user manual how to add or remove a leading strip 1. Place the original centrally and face down on the original feed table. The océ tds100 moves the original to the back. [10] feed the original with leading strip centrally and face down [10] feed the original with leading strip centrally and face ...

  • Page 33

    Use the océ tds100 33 how to add or remove a trailing strip 1. Place the original centrally and face down on the original feed table. The océ tds100 moves the original to the back. [11] feed the original with trailing strip centrally and face down [11] feed the original with trailing strip centrally...

  • Page 34

    34 user manual improve the copy quality of dark and light originals introduction you can use the exposure setting to improve the copy quality of a dark or light original. How to correct a dark original 1. Use the exposure key to select a value between 0 and +4 to lighten the copy. How to correct a l...

  • Page 35

    Use the océ tds100 35 check the copy quality with a test strip introduction before you start your copy job, you can check the result of your settings on the copy quality with a test strip. Attention: if the original contains a filing strip, make sure that the filing strip is at the trailing edge (se...

  • Page 36

    36 user manual straighten the edge of a media roll introduction you can use the 'cut' function to make the edge of a roll straight. Before you begin remove the original from the original feed table. How to cut the edge of a roll 1. Use the 'feed' key to select a roll 2. Use the 'cut' key to select '...

  • Page 37

    37 océ tds100 user manual chapter 3 maintain the océ tds100

  • Page 38

    38 user manual understand message codes introduction the océ tds100 displays a message code when the copier is not ready to use. The following table shows a summary of the messages codes, the possible cause and the action to take. What the message code describes code possible cause action e 0 ■ the ...

  • Page 39

    Maintain the océ tds100 39 add toner introduction the océ tds100 illuminates the toner low indicator when the toner level is low. When the toner low indicator illuminates, you need to do the following. ■ add toner ■ replace the waste toner bag. Note: if you ignore the toner low indicator, the copy q...

  • Page 40

    40 user manual how to add toner and replace the waste toner bag 1. Loosen the nut at the left back side. Open the left cover. [13] open the left cover [13] open the left cover 2. Before you open the bottle, shake the bottle thoroughly. Put the toner bottle in the bottle holder. Turn the bottle clock...

  • Page 41

    Maintain the océ tds100 41 3. Turn the bottle in the vertical position [15] turn the bottle [15] turn the bottle the toner flows into the océ tds100. 4. Wait until the bottle is empty return the bottle into the original position 5. Turn the bottle anticlockwise to loosen the bottle from the bottle h...

  • Page 42

    42 user manual clear an original jam introduction the media jam indicator blinks and the message code 'e 0' displays to indicate that an original jam occured. The type of original determines how to clear the original jam. The types of originals are divided into the following. ■ fragile originals ■ n...

  • Page 43

    Maintain the océ tds100 43 how to remove a normal original 1. Pull the original carefully with two hands toward you 2. Check on a media jam also and clear the media jam if necessary. (see ‘clear a media jam’ on page 44) result the original jam is cleared and the media indicator is off. The océ tds10...

  • Page 44

    44 user manual clear a media jam introduction the media jam indicator blinks and the message code 'e 3' displays to indicate that a media jam occured. A media jam can occur in one of the following sections ■ the manual media feeder ■ the fuser section. When to do you need to clear a media jam in the...

  • Page 45

    Maintain the océ tds100 45 2. Press the two handles at the underside of the manual feed table to lower the manual feed table [19] lower the manual feed table [19] lower the manual feed table 3. Remove the jammed media carefully 4. Lift the manual feed table until you hear or feel a click 5. Close th...

  • Page 46

    46 user manual how to remove the media from the fuser section caution: the fuser section can be hot. Attention: the jammed media can contain loose toner. 1. Turn off the océ tds100 2. Loosen the nut at the left back side. Open the left cover. [20] open the left cover [20] open the left cover 3. Lift...

  • Page 47

    Maintain the océ tds100 47 5. Lift the green handle and close the fuser unit [22] close the fuser cover [22] close the fuser cover 6. Close the left cover. Tighten the nut at the left back side. 7. Check on an original jam also and clear the original jam if necessary (see ‘clear an original jam’ on ...

  • Page 48

    48 user manual replace a media roll introduction the media jam indicator blinks and the message code 'e 5' displays to indicate that a media roll is empty. When you replace a media roll, you need to check or set the following before you close the roll section. ■ the media type ■ the roll number ■ th...

  • Page 49

    Maintain the océ tds100 49 2. Remove the roll holder from the drawer [24] remove the roll holder [24] remove the roll holder 3. Press the knob of the roll holder to remove the old media roll from the roll holder [25] press the knob of the roll holder [25] press the knob of the roll holder 2485.

  • Page 50

    50 user manual 4. Press the knob of the roll holder and slide the roll holder into the new roll. Press the knob of the roll holder to align the new roll with the correct media size on the roll holder. 5. Place the roll holder with the new media roll in the drawer. Make sure you put the loose end of ...

  • Page 51

    Maintain the océ tds100 51 how to replace media roll 2 1. Lift and turn the door in front of roll 2 [28] open the door in front of roll 2 [28] open the door in front of roll 2 2. Remove the roll holder 3. Press the knob of the roll holder to remove the old media roll from the roll holder [29] press ...

  • Page 52

    52 user manual 5. Place the roll holder with the new media roll in the drawer. Make sure you put the loose end of the media roll in the correct position. [30] place the roll holder [30] place the roll holder 6. Feed the media as far as the wheels. Turn the wheels to feed the media as far as the arro...

  • Page 53

    Maintain the océ tds100 53 clean the transparent plate introduction you need to keep the transparent plate clean. A dirty transparent plate causes a decreased copy quality. When to do clean the transparent plate when you have spots on the copies that are not on the original. Required tools 'océ clea...

  • Page 54

    54 user manual how to clean the transparent plate 1. Turn off the océ tds100 2. Pull the top cover towards you and lift the top cover to open it. [32] open the top cover [32] open the top cover 3. Clean the transparent plate with a lint-free cloth and a small quantity of the cleaner [33] do not dama...

  • Page 55

    55 océ tds100 user manual appendix a overview and tables.

  • Page 56

    56 user manual default values introduction the default values of the settings are active in the following situations. ■ turn on the océ tds100 ■ use the océ tds100 after sleep mode ■ press the red stop key twice. The default values of the settings of the sheet feed, single copy configuration the def...

  • Page 57

    Overview and tables 57 product specifications product specifications [2] the product specifications of the océ tds100 [2] the product specifications of the océ tds100 the validity of the product specifications the recommended operating environment is 30 - 60 % relative humidity and 20 - 27 °c temper...

  • Page 58

    58 user manual supported original types and sizes overview of supported original types and sizes [3] the supported original types and sizes of the océ tds100 [3] the supported original types and sizes of the océ tds100 overview of the conditions of the originals [4] the conditions of the originals [...

  • Page 59

    Overview and tables 59 supported media types and sizes introduction océ systems and materials are matched for optimal quality and performance. You are therefore recommended to use only approved océ materials in the océ tds100. A full list of océ materials is suitable for use in the océ tds100. The l...

  • Page 60

    60 user manual overview of supported media the copy quality on the supported media can be less than on the recommended media. [6] the supported media types of the océ tds100. [6] the supported media types of the océ tds100. Media supported type remark plain paper 100/110 g/m 2 transparent paper 60 g...

  • Page 61

    61 océ tds100 user manual appendix b miscellaneous.

  • Page 62

    62 user manual reader's comment sheet questions have you found this manual to be accurate? O yes o no were you able to operate the product, after reading this manual? O yes o no does this manual provide sufficient background information? O yes o no is the format of this manual convenient in size, re...

  • Page 63

    Miscellaneous 63 comments: --------------------------------------------------------------------------------------------- --------------------------------------------------------------------------------------------- -------------------------------------------------------------------------------------...

  • Page 64

    64 user manual addresses of local océ organisations océ-australia ltd. P.O. Box 363 ferntree gully mdc vic 3165 australia http://www.Oce.Com.Au/ océ-osterreich gmbh postfach 95 1233 vienna austria http://www.Oce.At/ océ-belgium n.V./s.A. J. Bordetlaan 32 1140 brussel belgium http://www.Oce.Be/ océ-b...

  • Page 65

    Miscellaneous 65 océ-deutschland gmbh solinger straße 5-7 45481 mülheim/ruhr germany http://www.Oce.De/ océ-hong kong and china head office 12/f 1202 the lee gardens 33 hysan avenue causeway bay hong kong http://www.Oce.Com.Hk/ océ-hungaria kft. 1241 budapest pf.: 237 hungary http://www.Oce.Hu/ océ-...

  • Page 66

    66 user manual note: the web site http://www.Oce.Com gives the current addresses of the local océ organisations and distributors. Note: the addresses of local océ organisations for information about the wide format printing systems and the production printing systems can be different from the addres...

  • Page 67

    Index 67 index a add toner 39 adjustment key (1 & 2 roll configuration) 12 adjustment key (multi copy configuration) 17 automatic feed copy 27 b background compensation 34 c clean the transparent plate 53 clear a media jam 44 clear an orignal jam 42 components overview 10 fuser cover 10 integrated r...

  • Page 68

    68 user manual j jam media jam 44 original jam 42 l leading strip 31 left cover 10 light original 34 m manual feed copy 29 manual feed table 10 media recommended media types 59 set media size 48 set media type 48 supported media sizes 59 supported media types 59 media (type, 1 & 2 roll configuration...

  • Page 69

    Index 69 red light 20 start 20 stop 20 toner indicator 20 options overview 9 original feed table 10 original jam 42 original sizes 58 original types 58 p product specifications 57 r red light (1 & 2 roll configuration) 12 red light (multi copy configuration) 17 red light (single copy configuration) ...