Summary of TDS100
Page 1
Océ tds100 quick reference guide.
Page 2: Océ-Technologies B.V.
Copyright © 2005, océ-technologies b.V. Venlo, the netherlands all rights reserved. No part of this work may be reproduced, copied, adapted, or transmitted in any form or by any means without written permission from océ. Océ-technologies b.V. Makes no representation or warranties with respect to the...
Page 3
Contents 3 contents chapter 1 about the océ tds100 the components 6 the operator panel 8 make copies 11 replace media rolls 12 add toner 13 clear jams 15.
Page 4
4 quick reference guide.
Page 5
5 océ tds100 quick reference guide chapter 1 about the océ tds100
Page 6
6 quick reference guide the components nr. Component function 1 on / off switch turn on and off the océ tds100. Note: the on / off switch is not visible in the illustration. 2 operator panel set up, start and control the copy jobs. 3 original feed table feed the original. 4 manual feed table feed th...
Page 7
About the océ tds100 7 note: some components may not be available on your océ tds100 due to the differences between the configurations. 7 integrated receiving tray receive the copies. 8 top cover give access to the transparent plate. 9 fuser cover give access to the fuser. Note: the fuser is not vis...
Page 8
8 quick reference guide the operator panel 4 2 0 -2 -4 media paper roll 1 trailing synchro film roll 2 leading standard feed manual strip cut toner media jam 6 8 1 2 3 4 5 14 13 10 12 7 9 11.
Page 9
About the océ tds100 9 the indicators nr. Indicator function 1 'toner' indicate that the océ tds100 has run out of toner. 2 green light indicate that the copier is ready. A blinking green light indicates that the copier runs a copy job. 3 red light indicate that an error has occurred. 4 'media jam' ...
Page 10
10 quick reference guide the keys note: some functions may not be available on your océ tds100 due to the differences in the configurations. Nr. Key function 6 'media' select the media type. 7 'feed' select the media feed method. 8 exposure adjust the exposure. Use the exposure setting to correct th...
Page 11
About the océ tds100 11 make copies how to copy on a roll medium (automatically) how to copy on a cut sheet (manually) step action 1 place the original centrally and face down on the original feed table. The océ tds100 moves the original to the back. 2 make the required settings. 3 press the green s...
Page 12
12 quick reference guide replace media rolls how to replace a media roll step action 1 open the drawer with roll 1 or the door in front of roll 2. 2 replace the media roll and follow the instructions on the sticker. 3 use the 'feed' key to select the roll number of the new roll. 3 use the 'media' ke...
Page 13
About the océ tds100 13 add toner how to add toner step action 1 loosen the nut at the left back side. Open the left cover. 2 before you open the bottle, shake the toner bottle thoroughly. Put the toner bottle in the bottle holder. Turn the bottle clockwise to fasten the bottle..
Page 14
14 quick reference guide 3 turn the bottle in the vertical position. 4 wait until the bottle is empty. Return the bottle into the original position. 5 turn the bottle anticlockwise to loosen the bottle from the bottle holder. 6 pull the waste toner bag from its holder. Close the waste toner bag. 7 s...
Page 15
About the océ tds100 15 clear jams how to remove a jammed original step action 1 open the top cover in case of a fragile original. Pull the top cover towards you and lift the top cover to open it. 2 pull the original carefully with two hands towards you 3 check on a media jam also and clear the medi...
Page 16
16 quick reference guide how to remove the media from the manual feed table attention: make sure you lower the sheet feeder before you remove the media. Step action 1 open the middle cover. 2 press the two handles at the underside of the manual feed table to lower the manual feed table. 3 remove the...
Page 17
About the océ tds100 17 how to remove the media from the fuser unit caution: the fuser section can be hot. Attention: the jammed media can contain loose toner. Step action 1 turn off the océ tds100. 2 loosen the nut at the left back side. Open the left cover. 3 lift the green handle and open the fus...
Page 18
18 quick reference guide 5 lift the green handle and close the fuser cover. 6 close the left cover. Tighten the nut at the left back side. 7 turn on the océ tds100. Step action.