1. DL manuals
  2. Octane Fitness
  3. Elliptical Trainer
  4. Pro 370
  5. Assembly Manual

Octane Fitness Pro 370 Assembly Manual

Other manuals for Pro 370: Operation Manual

Summary of Pro 370

  • Page 2

    2.

  • Page 3: P R O 3 7 0

    3 p r o 3 7 0 a s s e m b l y i n s t r u c t i o n s personal record keeping tip: record the serial numbers of your octane fitness ® elliptical in the spaces below. This will make it easier for you to obtain accurate and timely response should any service issues occur with your elliptical machine. ...

  • Page 4

    4 a p r o 3 7 0 c o n t e n t s the octane fitness base box contains the following: tools required: a) 1-octanefitnesscrosstrainerbase • phillipsscrewdriver b) 1-consolemast • 17mmwrenchoradjustablewrench c) 1-topcover • 17mmsocketandratchet d) 1 - access panel • 6mmhexkeywrench e) 1 - detached righ...

  • Page 5

    5 hardware pack (j) includes: k) 8-6mmhexkeychamferedbolt(formovinghandlebars) l) 2-phillipsscrews(formountingaccesspanel) m) 2-phillipsscrewswithwashers(formountingtopcover) n) 1 - cable tie (for securing loose wires) k l m n the pro370 console box contains the following: 1) 1 - console 2) 1 - keyp...

  • Page 6

    6 2. Attach moving handlebars—moving handlebars are labeled left and right, be sure to install accordingly. A. Align the bottom of the handlebar (f or g) with the four holes inthepivotshaftandattachwithfour6mmhexkeybolts (k)—make sure these bolts are very tight; torque to 30 ft-lbs. B. Reaching insi...

  • Page 7

    7 4. Install console mast a. Attach the console mast (b) by placing the keyhole slots in the mast plate over the bolts on the cross trainer base (a) and sliding the console mast toward the pedals. B. Tightenthefour6mmhexkeyboltsattachingconsolemast to frame. C. Connect the black cable connector comi...

  • Page 8

    8 6. Mount the console to the console mast note: record the serial number of your console, located on the lower edge of the console, before attaching the console to the console mast. (if you have installed the optional lcd mounting arm, and mounted the console to the mast according to those instruct...

  • Page 9

    9 7. Adjust arms (optional) note: before completing this step, plug in and ride your elliptical cross trainer for a few moments to get a feel for the arm motion. If the reach of the arm motion feels right (as it will for most users), proceed to step 8. If the reach is too long or too short, carefull...

  • Page 10

    10 9. Install mast boot a. Placetherubbermastboot(i)aroundthemast(b),covering the open ends of the stationary handlebars. B. Tuck the ends of the mast boot (i) into the channels in the accesspanel(d)justbelowthestationaryhandlebars. 10. (optional) csafe connection a. If your facility is using csafe,...

  • Page 11

    11 12. Set user preferences a. Pressandholdboth the up arrow () and down arrow () keys for three seconds, or until you hear a double-beep. Working with the owner of the unit, use the up arrow () or down arrow () key to step through the customizable functions: warm-up (on/off), clock direction (u...

  • Page 12: ™

    F u e l y o u r l i f e ™ 9200wyomingavenuenorth,suite380 brooklynpark,mn55445 1.888.Octane4 www.Octanefitness.Com ©2008octanefitness,llc™. All rights reserved. Octane fitness, dedicatedlogic, fuel your life, heartlogic, now-zone and x-mode are registered trademarks of octane fitness. Any use of the...