OHAUS CD-11 Instruction Manual - page 22
PAGE 22 OF 30
0908 IH-606
H-606
23
4. OPERATION (Cont.)
4.7 Unit Switch Operation (Cont.)
If enabled in program mode, additional units of measure may be utilized beyond the primary unit of measure used for
callibration or display. Switching between primary and secondary units is accomplished by pressing the Print/Units
button. Which unit is displayed depends on the current units being used. The following tables detail the graduation
size conversions when switching between kg, lb and g.
Cal unit
Alternate Unit.
Alternate Unit
in Lb
Lb
kg
g
0.001
0.001
1
0.002
0.001
1
0.005
0.002
2
0.01
0.005
5
0.02
0.01
N/A
0.05
0.02
N/A
0.1
0.05
N/A
0.2
0.1
N/A
0.5
0.2
N/A
1
0.5
N/A
2
1
N/A
5
2
N/A
Cal unit
Alternate Unit.
Alternate Unit
in Lb
KG
LB
g
0.001
0.002
1
0.002
0.005
2
0.005
0.01
5
0.01
0.02
N/A
0.02
0.05
N/A
0.05
0.01
N/A
0.1
0.2
N/A
0.2
0.1
N/A
0.5
1
N/A
1
2
N/A
2
5
N/A
5
N/A
N/A
4.8 Parts Counting Operation
Parts counting is enabled only when turned ON in the
Readout menu. Refer to paragraph 2.7.5. In the parts
counting mode, the Indicator displays the quanitity of
parts placed on the platform. The Indicator determines
the quanitity based on the average weight of a single
part. All parts must be reasonably uniform in weight for
accurate measurements.
4.9 Establishing a New Average
Piece Weight (APW)
If the APW has not been calculated previously, proceed
as follows:
• Press and hold Print/Units button until Pcs cursor
is displayed.
• Press and hold Zero/Menu until SEtPCS is dis-
played. This is displayed for about 1 second, then
SEt 5 is displayed.
• Select an alternate sample size by pressing and
holding Print/Units button. Choices are 5, 10, 20,
and 50. Place count samples on platform.
Pcs Gross
Brutto
Pcs Gross
Brutto
CD-11 Indicator
24
4. OPERATION (Cont.)
4.9 Establishing a New Average
Piece Weight (APW) (Cont.)
• Press Zero/Menu button to accept current sample.
The new APW is established. Place parts on plat-
form or in a container to count. If a container is
used, be sure to tare the empty container first.
• Additional samples may be added to the platform as
long as the same sample weight intially entered is
used with the samples being weighed.
Pcs Gross
Brutto
Pcs Gross
Brutto
Pcs Gross
Brutto
Pcs Gross
Brutto
Stable
4.10 Returning to a Weighing Mode
• Press Print/Units button until the display indicates
the desired measuring unit either kg, lb or g.
Stable
Gross
Center
of zero
4.11 Returning to a Preset APW
If the APW has been calculated previously, the Indicator
stores the value in memory. Proceed as follows to use a
previously set APW:
• Press and hold Print/Units button until Pcs cursor
is displayed.
• Place samples on the platform. The display indicates
the number of pieces based on the previously en-
tered data. Sample shown at left indicates 100
pieces.
Stable
Gross
Center
of zero
Pcs
Pcs Gross
Brutto
Stable
CAUTION
WHEN POWER IS TURNED OFF, APW
WILL ALWAYS RETURN TO DEFAULT
APW 5.
CD-11 Indicator