- DL manuals
- OHAUS
- Scales
- SD Series
- Instruction Manual
OHAUS SD Series Instruction Manual
Summary of SD Series
Page 1
I sd series bench scale báscula de mesa de la serie sd balance de table série sd tischwaage der sd-serie bilancia da banco serie sd sd-manual original.Indb 1 9/8/2006 3:09:48 pm.
Page 2
Ii sd-manual original.Indb 2 9/8/2006 3:09:48 pm.
Page 3
Iii this product conforms to the emc directive 89/336/eec and the low voltage directive 73/23/eec. The complete declaration of conformity is available from ohaus corporation. Questo prodotto è conforme alla direttiva emc 89/336/cee e alla direttiva bassa tensione 73/23/cee. La dichiarazione di confo...
Page 4
Iv disposal in conformance with the european directive 2002/96 ec on waste electrical and elec- tronic equipment (weee) this device may not be disposed of in domestic waste. This also applies to countries outside the eu, per their specific requirements. Please dispose of this product in accordance w...
Page 5
V entsorgung in Übereinstimmung mit den anforderungen der europäischen richtlinie 2002/96 eg über elektro- und elektronik-altgeräte (weee) darf dieses gerät nicht mit dem hausmüll entsorgt werden. Sinngemäss gilt dies auch für länder ausserhalb der eu entsprechend den geltenden nationalen regelungen...
Page 6
Vi fcc note this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and...
Page 7
Sd series bench scale en-1 ohaus sd series bench scale instruction manual • the contents of this manual applies to all models of the sd series bench scale. • calibration weights are not provided with this product. • for best results, use the product within the specified operating temperature range. ...
Page 8
En-2 sd series bench scale introduction this manual covers operation for the ohaus sd series bench scales. Unpacking sd series bench scale is shipped with the following components: • indicator • ac power adapter • scale base • this instruction manual • mounting brackets • warranty card leveling scal...
Page 9
Sd series bench scale en-3 battery installation (optional) • open the battery cover on the bottom of the indicator and install three “c” size (lr14) alkaline batteries into the compartment. Orient the batteries as shown on the inside cover. Close the battery cover. Note : batteries are not included....
Page 10
En-4 sd series bench scale figure 3. Direct wall mount arrangement. • bracket wall mounting/table mounting : attach the two mounting brackets as shown in figure 4. Position the indicator where desired on the wall or table. Install 2 screws (not supplied) into the ends of each bracket to secure them ...
Page 11
Sd series bench scale en-5 product features & operation figure 5. Indicator panel controls. Two button keypad • on/zero off : a short press turns on the scale when it is off. When the scale is on, a short press zeroes the scale, and a long press turns the scale off. • units cal : a short press chang...
Page 12
En-6 sd series bench scale • low battery indication : the battery symbol on the left side of the display indicates a low battery condition. When first displayed , approximately 12 hours of operation remain. When the battery is fully depleted, the scale will momentarily display “lo bat” and shut off....
Page 13
Sd series bench scale en-7 • auto shut-off : to extend battery life, the scale will automatically turn off after approximately four minutes of inactivity. This feature is only active during battery operation. Calibration for best results, calibrate the scale at regular intervals. (calibration weight...
Page 14
En-8 sd series bench scale 5. After the zero is captured, the required span calibration weight in the selected unit is displayed. 6. Place the calibration weight on the platform and press on/zero off button. The display will again show “-c-”. 7. After span capture, the display will return to the nor...
Page 15
Sd series bench scale en-9 model sd35 sd75 sd200 capacity x readability 35 x 0.02kg 77 x 0.05lb 75 x 0.05kg 165 x 0.1lb 200 x 0.1kg 440 x 0.2lb weighing units kg, lb calibration weights 25kg/50lb 50kg/100lb 100kg/200lb stabilization time within 3 seconds zero range to capacity by subtraction maximum...
Page 16
En-10 sd series bench scale model sd75l sd200l capacity x readability 75 x 0.05kg 165 x 0.1lb 200 x 0.1kg 440 x 0.2lb weighing units kg, lb calibration weights 50kg/100lb 100kg/200lb stabilization time within 3 seconds zero range to capacity by subtraction maximum overload 150% error indications: “e...
Page 17
Sd series bench scale en-11 figure 6. Scale base overall dimensions. 53mm /2.09” 69mm / 2.72” 39mm / 1.54” 210mm / 8.27” 91mm / 3.58” 280mm / 11.02” 45mm / 1.77” figure 5. Indicator overall dimensions, available viewing angles. 0º 50º 70º standard base large base 316mm / 12.44” 400 mm / 15.7” 520mm ...
Page 18
En-12 sd series bench scale limited warranty ohaus products are warranted against defects in materials and workmanship for duration of the warranty. During the warranty period ohaus will repair, or, at its option, replace any components) that proves to be defective at no charge, provided that the pr...