DL manuals
OHAUS
Scales
SPX1202
Instruction Manual

OHAUS SPX1202 Instruction Manual - 3.4 Weighing

Manual is about: Scout Series SPX

Page of 22

Download

Print this page

Bookmark us

EN-6 SCOUT

SERIES BALANCES - SPX

3.4 Weighing

Mode

This mode is the factory default setting.

1. If needed, press and hold Mode until [wWeIGH] (Weigh) is displayed.

2. If required, place an empty container on the pan and press Tare.

3. Add sample to the pan or container. The display shows the weight of the sample.

3.5 Counting Mode

This mode counts large numbers of items based on the weight of a reference count.

1. Place an empty container on the pan and press Tare.

2. Press and hold Mode until [Count] (Count) is displayed. [CLr.PwW] (Clear Average Piece

Weight, APW) will then display.

If no APW exists, the balance will display [Put.10], proceed to step 5.

3. Press No to use the stored APW. Proceed to step 7.

4. Press Yes to establish an APW.

5. The balance will then display the stored sample size, i.e. [Put 10]. Press No or Back to

toggle the choices (5, 10, 20, 50 or 100).

6. Put the indicated number of pieces on the pan then press Yes to calculate the APW. The

display shows the piece count.

7. Add additional pieces until the desired count is reached.

8. To clear the stored APW press and hold Mode until [Count] is displayed. Press Yes when

[Clr.pwW] is displayed.

Note: Press Function to view the current APW.

3.6 Percent Mode

This mode measures the weight of a sample as a percentage of a reference weight.

1. If required place an empty container on the pan and press Tare.

2. Press and hold Mode until [Percnt] is displayed. [Clr.ref](clear reference) will then

display. If no reference weight exists, the balance will display [Put.ref], proceed to step 5.

3. Press No to use the stored reference weight and proceed to step 6.

4. Press Yes to establish a new reference. Balance will now display [Put.ref].

5. Add the desired reference material to the pan or container. Press Yes to store the

reference weight. The display shows 100%.

6. Replace the reference material with the sample material. The display shows the

percentage of the sample compared to reference weight.

7. To clear the stored reference press and hold Mode until [Percnt] is displayed. Press Yes

when [Clr.ref] is displayed.

Note: Press Function to view the current reference weight.

(866) 433-6682 • (281) 359-8538 • sales@novatech-usa.com • www.novatech-usa.com

« ‹ Prev 4 5 6 7 8 9 10 Next › »

Summary of SPX1202

Page 1
Scout tm series balances - spx instruction manual sales@novatech-usa.Com www.Novatech-usa.Com tel: (866) 433-6682 fax: (866) 433-6684 tel: (281) 359-8538 fax: (281) 359-0084.
Page 2: 1. Introduction
Scout tm series balances - spx en-1 1. Introduction this manual contains installation, operation and maintenance instructions for the scout spx series balances. Please read the manual completely before using the balance . 1.1 definition of signal warnings and symbols safety notes are marked with sig...
Page 3
En-2 scout tm series balances - spx 2.1.1 releasing the transportation lock release the red transportation lock on subplatform of the balance by turningthe red pointer 90 counter-clockwise. Figure 2-1. Transportation lock 2.1.2 installing the weighing pan balances with a rectangular pan are placed i...
Page 4: 2.4 Connecting Power
Scout tm series balances - spx en-3 2.4 connecting power ac adapter installation ac power is used to power the scale when battery power is not needed. First, connect the ac adapter (supplied) to the ac adapter input jack at the rear of the balance then connect the ac plug to an electrical outlet. Fi...
Page 5: 3. Operation
En-4 scout tm series balances - spx 3. Operation 3.1 controls figure 3-1. Scout control panel table 3-1. Button functions button primary function (short press) zero/on turns the balance on if balance is on, sets zero print sends the current value to the selected com ports if autoprint is set to off....
Page 6: 3.3 Calibration Operation
Scout tm series balances - spx en-5 figure 3-1. Scout display table 3-2. Display symbols* item description item description 1 battery charge symbol 8 kilogram, grain symbols 2 stable weight symbol 9 check weighing symbols 3 negative symbol 10 pound, ounce, pound:ounce symbols 4 center of zero symbol...
Page 7: 3.4 Weighing
En-6 scout tm series balances - spx 3.4 weighing mode this mode is the factory default setting. 1. If needed, press and hold mode until [wweigh] (weigh) is displayed. 2. If required, place an empty container on the pan and press tare. 3. Add sample to the pan or container. The display shows the weig...
Page 8: 3.7 Check Mode
Scout tm series balances - spx en-7 3.7 check mode use this mode to compare the weight to a target weight range. The balance supports positive, negative and zero check weighing. 3.7.1 check weighing use this mode to compare the weight of items to a target weight range. 1. Press and hold mode until [...
Page 9: 3.8 Totalization Mode
En-8 scout tm series balances - spx 3.8 totalization mode this mode allows the user to store a series of weight measurements. Totalize mode has been initiated when the symbol “ ∑ ” is displayed and the current unit is displayed. Notes: only positive numbers are totalized. 1. Press and hold mode unti...
Page 10: 4. Menu Settings
Scout tm series balances - spx en-9 4. Menu settings the user menu allows the customizing of balance settings. Note: additional sub-menus may be available if interface options are installed. See interface user manual for the additional setting information. 4.1 menu navigation user menu: sub-menus c....
Page 11: 4.3 Setup Menu
En-10 scout tm series balances - spx 4.3 setup menu enter this menu to set balance parameters. Note: bold always represents factory default value reset [reset] reset the setup menu to factory defaults. No = not reset yes = reset filter [filter] set the amount of signal filtering. Low = less stabilit...
Page 12: 4.4 Mode Menu
Scout tm series balances - spx en-11 auto off [a.Off] set the automatic shut off functionality. Off = disabled 1 = powers off after 1 minute of no activity 5 = powers off after 5 minutes of no activity 10 = powers off after 10 minutes of no activity end setup [end] advance to the next menu or return...
Page 13: 4.5 Unit Menu
En-12 scout tm series balances - spx hold [hold] set the sub-mode. Off = disabled peak hold = allows the user to capture and store the highest stable weight value (>=5d). Display hold = allows the user to capture and store the first stable weight value (>=5d). When the stable value is being held on ...
Page 14
Scout tm series balances - spx en-13 exponent set the factor multiplier. -3 = divide the factor by 1000 (1x10 -3 ) -2 = divide the factor by 100 (1x10 -2 ) -1 = divide the factor by 10 (1x10 -1 ) 0 = multiply the factor by 1 (1x10 0 ) 1 = multiply the factor by 10 (1x10 1 ) 2 = multiply the factor b...
Page 15: 4.6 Additional Features
En-14 scout tm series balances - spx 4.6 additional features weigh below hook the scout balance is equipped with a weigh below hook for weighing below the balance. The weigh below hook is located at the reverse side of the battery cover as shown below. To use this feature, remove the red protective ...
Page 16: 5. Maintenance
Scout tm series balances - spx en-15 5. Maintenance 5.1 cleaning warning: electric shock hazard. Disconnect the equipment from the power supply before cleaning. Electric shock hazard. The housing may be cleaned with a cloth dampened with a mild detergent if necessary. Attention: do not use solvents,...
Page 17: 6. Technical Data
En-16 scout tm series balances - spx 6. Technical data the technical data is valid under the following ambient conditions: indoor use only operating temperature range: +5°c to +40°c relative humidity: 10% to 80% at 31°c, decreasing linearly to 50% at 40°c, non-condensing altitude: up to 2000 m power...
Page 18
Scout tm series balances - spx en-17 table 6-2. Specifications cont. Capacity x readability: model spx123 spx223 spx222 spx422 spx622 spx1202 spx2202 gram (g) 120 x 0.001 220 x 0.001 220 x 0.01 420 x 0.01 620 x 0.01 1200 x 0.01 2200 x 0.01 kilogram (kg) / / / / / 1.2 x 0.00001 2.2 x 0.00001 carat (c...
Page 19: 6.2
En-18 scout tm series balances - spx table 6-4. Specifications cont. Capacity x readability: model spx421 spx621 spx2201 spx6201 spx8200 gram (g) 420 x 0.1 620 x 0.1 2200 x 0.1 6200 x 0.1 8200 x 1 kilogram (kg) / / 2.2 x 0.0001 6.2 x 0.0001 8.2 x 0.001 carat (ct) 2100 x 0.5 3100 x 0.5 11000 x 0.5 31...
Page 20
Scout tm series balances - spx en-19 important notice for verified weighing instruments in the eu when the instrument is used in trade or a legally controlled application it must be set up, verified and sealed in accordance with local weights and measures regulations. It is the responsibility of the...
Page 21
En-20 scout tm series balances - spx iso 9001 registration in 1994, ohaus corporation, usa, was awarded a certificate of registration to iso 9001 by bureau veritus quality international (bvqi), confirming that the ohaus quality management system is compliant with the iso 9001 standard’s requirements...
Page 22
Scout tm series balances - spx en-21 ohaus corporation 7 campus drive suite 310 parsippany, nj 07054 usa tel: +1 973 377 9000 fax: +1 973 944 7177 with offices worldwide / con oficinas alrededor del mundo / avec des bureaux dans le monde entier / weltweite geshäftsstellen / con uffici in tutto il mo...