(hq) sato international pte. Ltd. (japan) sato corporation (singapore) sato asia pacific pte. Ltd. (malaysia) sato auto-id malaysia sdn. Bhd. (thailand) sato auto-id (thailand) co., ltd (china) sato shanghai co., ltd (usa) sato america, inc. (belgium) sato europe nv (germany) sato deutchland gmbh (p...
Sato asia pacific pte. Ltd. 438a alexandra road #05-01/02 alexandra technopark singapore 119967 tel : (65) 6271 5300; fax : (65) 6273 6011 sales hotline : (65) 6276 2722; service hotline : (65) 6273 6455 email : sales@satoasiapacific.Com website : www.Satoworldwide.Com © copyright 2003 sato asia pac...
M-84pro quick guide pg 23 accessories & options pcmcia memory expansion one slot for pcmcia memory card (up to 4 mb sram or 16 mb flash rom). Can be used for graphic file storage, print buffer expansion, format storage and downloaded fonts. Flash rom expansion internal 4mb flash rom pcb real time cl...
M-84pro quick guide pg 1 table of contents installation …………………………………………………………………….. 2 installation ……………………………………………………………. 2 components …………………………………………………………… 3 media loading ………………………………………………………………... 5 label stock loading ………………………………………………….. 5 ribbon loading ………………………………………………………. 8 operatio...
M-84pro quick guide pg 21 print-outs vector fonts proportional or fixed spacing font size 50 x 50 dots to 999 x 999 dots helvetica, 10 font variations rotation 0º , 90º , 180º , and 270º rotation graphics dot addressable, sato hex/binary, bmp or pcx formats specification m-84pro all models controls ...
M-84pro quick guide pg 3 components m-84pro quick guide pg 20 m-84pro specifications general printer specifications specification m-84pro-2 m-84pro-3 m-84pro-6 print method direct or thermal transfer speed (user selectable) 2 to 10 ips 50 to 250 mm/s 2 to 8 ips 50 to 200 mm/s 2 to 6 ips 50 to 150 mm...
M-84pro quick guide pg 19 error blinks ribbon end 3 short ribbon end 1. Needs new ribbon roll 2. Ribbon sensor needs adjustment download error r/w error mem full error 3 short download error 1. Read/write error 2. Corrupted download file 3. Download file too large copycard/ format r/w error no card ...
M-84pro quick guide pg 5 media loading label stock loading 1. Open the top access door by swinging it up and to the left. Open the side access door by swinging it to rear of the printer. 2. Open the print head assembly by pushing the head latch towards the rear of the printer. The print head assembl...
M-84pro quick guide pg 17 intermittent problems if the print server and the printer start up ok, but you intermittently have problems printing, check the following: 1. Excessive netware polling can be a big cause of intermittent problems. Make sure that you have only enabled the netware file servers...
M-84pro quick guide pg 7 11. Adjust the outside label edge guide until it touches the outside edge of the label and tighten the thumb screw. Make sure the labels are also touching the inside edge guides. Caution: using media narrower than the maximum print width may cause excess head wear due to the...
M-84pro quick guide pg 15 6. If you are still unable to get printer output, try the hex dump as described in step 5 under the parallel interface troubleshooting. In this case, the printer monitors the rs232c interface for incoming data. 7. From the hex dump, if you are seeing extra 0dh 0ah (cr and l...
M-84pro quick guide pg 9 7. Manually turn the rewind spindle to wrap the ribbon onto the core one to two turns to secure it. 8. 9. If the labels or tags are already loaded, close the print head assembly by pushing downwards on the black tab until it latches closed. 10. Run a test print to ensure tha...
M-84pro quick guide pg 13 troubleshooting initial checklist 1. Is the printer powered up and on-line? 2. Is the error light on the front panel off? If this light is on, it may mean the print head assembly or the label hold-down is not closed and latched in position. 3. Are the label and ribbon light...
M-84pro quick guide pg 11 feed momentary switch. Pressing this key feeds one blank label when the printer is off-line. When the printer is on-line, another copy of the last label will be printed (reprint w/feed must be enabled in the lcd panel service mode). Dsw dip switch array to set operational p...
