1. DL manuals
  2. PACIFIC CYCLE
  3. Toy
  4. 22-PS311
  5. Owner's manual and assembly instructions

PACIFIC CYCLE 22-PS311 Owner's manual and assembly instructions

Manual is about: Westport 8-Leg Swing Set Playsafe

Summary of 22-PS311

  • Page 1

    1 ©2007 pacific cycle, inc. Owner’s manual and assembly instructions model #: 22-ps311 model name: westport 8-leg swing set manual issued: april, 2009 important: keep this owner’s manual; do not discard in case you need to contact pacific cycle, inc. In the future. Should there be a change of owners...

  • Page 2

    2 ©2007 pacific cycle, inc. To make claim under warranty, notification of such defect must be given to pacific cycle, inc. By calling the phone number below, you will be instructed on how the product or part needing replacement should be shipped postpaid to pacific cycle, inc. Customer service and a...

  • Page 3

    3 ©2007 pacific cycle, inc. Warnings and safety information o bserve all warnings and statements in order to reduce the risk of injury or death . • before you assemble the swing set , find level ground not less than 6 feet from any structure or obstruction to the swing set . Y our swing set must hav...

  • Page 4

    4 ©2007 pacific cycle, inc. Proper use this swing set is designed for use by children ages 2 to 10 under adult supervision. The maximum number of users this unit is intended for is 9 children with a maximum weight of 105 lbs each. The maximum fall height for this swing set is 74” and the maximum fal...

  • Page 5

    5 ©2007 pacific cycle, inc. Checked periodically and replenished to maintain correct depth as determined necessary for your equipment. The choice of a material depends on the type and height of the playground equipment, the availability of material in your area and its cost. (the information above h...

  • Page 6

    6 ©2007 pacific cycle, inc. Slide name each rail/ladder leg 2 front leg 2 slide 1 ladder step 2 leg support bar 1 pre-assembled hardware for easier assembly, playsafe™ has pre-assembled some of the parts for you. Most of the screws and bolts should already be in place. If removal of this hardware is...

  • Page 7

    7 ©2006 pacific cycle, inc. 2 remove the hardware from the arm of a corner leg fitting in order to insert one of the legs. Note: four leg sections are shorter than the others. These are the center legs. Also, one leg has two holes near the base. The see-saw attaches to this leg and needs to be place...

  • Page 8

    8 ©2006 pacific cycle, inc. Glider assembly required parts: vertical poles x2 (footrests attached) horizontal poles x2 (seats attached) glider attachment x1 pre-assembled parts: • the seats should be attached to the horizontal poles. These must be disassembled to complete the steps below. • the foot...

  • Page 9

    9 ©2006 pacific cycle, inc. 3 connect the two horizontal poles (must first be disassembled from the seats) to the two vertical poles using the hardware provided. Be sure that the plastic bushings are between the vertical poles and horizontal poles. Part ref. #: pshw15, pshw11 4 reattach the seats on...

  • Page 10

    10 ©2006 pacific cycle, inc. Swing, rope disc, and trapeze assembly pre-assembled parts • swing seats should be attached to the chains. • trapeze should be attached to the chains. • rope disc should be attached to the rope. Step illustration instructions hardware reference 1 hang the swings, rope di...

  • Page 11

    11 ©2006 pacific cycle, inc. • the screws and bolts for the slide rail/ladder legs are inserted on the slide. They will need to be removed prior to inserting the legs into the slide. • the ladder steps should have screws and nuts installed. These will need to be removed prior to inserting the legs a...

  • Page 12

    12 ©2006 pacific cycle, inc. See-saw assembly required parts: see-saw bar and extension frame attachment support attachment seat x2 step illustration instructions hardware reference 1 remove the hardware from the frame attachment and connect the extension. Re- insert the hardware and tighten. Note: ...

  • Page 13

    13 ©2006 pacific cycle, inc. 4 mount the pivot onto the frame attachment. The pivot should be between the two screw heads, starting with the plastic bushing and then the metal bracket. 5 attach the see-saw bar to the pivot using the hardware found on the see-saw bar. Part ref. #: pshw10 6 once fully...