6 hp gas pressure washer model 95618 set up and operating instructions diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by harbor freight tools ® . 3491 mission o...
Sku 95618 for technical questions please call 1-800-444-3353 page 2 specifications gas engine 6hp ohv mitsubishi engine, 3600 rpm, recoil start, uses unleaded fuel, 20 oz. Engine oil capacity, 8.3 gal. Fuel capacity (3.8l). Environmental approved by epa (environmental protection agency) approved by ...
Sku 95618 for technical questions please call 1-800-444-3353 page 3 3. Injection hazard. The high pressure water jet produced by this tool can cut skin or cause injury to hands or eyes. Do not allow spray to strike you and do not spray toward people or animals. Do not spray the tool itself or any el...
Sku 95618 for technical questions please call 1-800-444-3353 page 4 remove adjusting keys and wrenches 15. . Check that keys and adjusting wrenches are removed from the tool or machine work surface before turning engine on. Avoid unintentional starting 16. . Be sure the water supply is in the off po...
Sku 95618 for technical questions please call 1-800-444-3353 page 5 in case of emergency during use, immediately release the trigger on 26. The spray handle, then turn the engine off. Do not set the spray handle down without turning off the engine. Then shut off gas supply to engine. (re- fer to eng...
Sku 95618 for technical questions please call 1-800-444-3353 page 6 unpacking when unpacking, check to make sure the parts shown in the photo below and in the diagrams on pages 13 and 14 are included. If any parts are missing or broken, please call harbor freight tools at the number on the cover of ...
Sku 95618 for technical questions please call 1-800-444-3353 page 7 checking pump’s oil level the oil pump is filled with 80 ml of sae 75w/90 oil at the factory. Under 1. Normal conditions there is no reason to add any oil or change the oil. It is however recommended that the customer verify the pum...
Sku 95618 for technical questions please call 1-800-444-3353 page 8 assembly note: please refer to the photo above and the table and diagram on pages 13 and 14 when reading this section and assembling your pressure washer. 1. Attach the cart handle (16) to the cart frame (5) as shown in the photo be...
Sku 95618 for technical questions please call 1-800-444-3353 page 9 using detergent caution! To avoid injury, only run pressure washer detergent through the detergent suction hose (46). Figure a 1. Press the supplied detergent suction hose (46) onto the fitting on top of the pump. Place the other en...
Sku 95618 for technical questions please call 1-800-444-3353 page 10 important guidelines for water supply 1. Do not leave engine running without spraying water. If engine is left running for more than three (3) minutes without discharging water, excess pressure can cause damage to the pump seals an...
Sku 95618 for technical questions please call 1-800-444-3353 page 11 operation pick up the spray gun (43) and point it in a safe direction. Squeeze the 1. Spray gun trigger until all internal air is released, and a steady flow of water comes out. Then release the spray trigger. Turn the fuel valve (...
Sku 95618 for technical questions please call 1-800-444-3353 page 10 page 12 turn off the water supply faucet. 3. Point the nozzle in a safe direction, then press the spray gun trigger handle 4. To release water and pressure. Disconnect the water supply hose from the water inlet connector. (see 5. P...
Sku 95618 for technical questions please call 1-800-444-3353 page 13 cially a concern when cleaning tile and grout, bricks and mortar, or stones and mortar. If wood is being cleaned, be careful not to damage it. Wood will usually require resurfacing (sanding) and re-coat with a surface protectant (w...
Sku 95618 for technical questions please call 1-800-444-3353 page 14 troubleshooting symptom possible cause solution engine will not start gas tank empty 1. Low oil level 2. Choke is not in correct position 3. Engine throttle set too low 4. Pressure build up in pump 5. Fill gas tank 1. Add oil 2. Cl...
Sku 95618 for technical questions please call 1-800-444-3353 page 14 note: some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. Assembly drawing.
Sku 95618 for technical questions please call 1-800-444-3353 page 14 please read the following carefully the manufacturer and/or distributor has provided the parts diagram in this manual as a reference tool only. Neither the manufacturer nor distributor makes any representation or warranty of any ki...
Sku 95618 for technical questions please call 1-800-444-3353 page 15 limited 1 year warranty harbor freight tools co. Makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials ...
