1. DL manuals
  2. Pacific
  3. Ventilation Hood
  4. PR830AS
  5. Use, Care & Installation Manual

Pacific PR830AS Use, Care & Installation Manual

Summary of PR830AS

  • Page 1

    Xp022396(1) 抽 油 煙 機 使 用 說 明 書 型號:pr830as / pr836as 抽油機型號: 序 號: xp022396(1) use,care,and lnstallation guide model:pr830as / pr836as model number: serial number:.

  • Page 3

    Table of content i. Product functions/performance specification chart .. . 1 ii. Parts instructions ................................................…. . 2 iii. Installation guidelines …………………………………. . 3 iv. Installation procedures …………………………..……. . 4 v. Venting instruction…………………………………...… . 5 vi. I...

  • Page 4

    1. 1. 一.功能簡介/性能規格表 pr836as 44磅 120v – 60hz 圓型 6吋,方型 3-1/4"x10" 吋 36”x22.5”x8” pr830as pr836as pr830as 40.7磅 120v – 60hz 圓型 6吋,方型3-1/4"x10"吋 2a/225w 2a/225w 2a/225w 2a/225w 鹵素燈 35wx2 鹵素燈 35wx2 30”x22.5”x8” 1. 3速風速選擇。 2. 可控制燈的開/關，具亮、暗二段調整。 a.功能簡介 b.性能規格表 淨 重 (英磅) 型 號 尺 寸 (英吋) 最大伏特數 風 管 直 徑 燈 泡 最 大 消 耗...

  • Page 5

    Pr830as / pr836as ii. Parts instructions 二.配件說明 2. 2. 種類 數量 螺絲包配件: 序號 p3螺母 5 x 24m/m 華司 m6 x 1-1/2吋木螺絲 m6 x 1吋木螺絲 m6 x 2吋木螺絲 3/16 x 1/2 平頭田丸十字螺絲 吊掛組 3 4 4 4 4 1 2 4 a f c b d e h g 鹵素燈拆裝吸盤 description n° hardware package contents type wire nuts 5 x 24 m/m washers m6 x 1-1/2” wood screws m6 x 1” wood...

  • Page 6

    3. 3. Iii. Installation guidelines notice the surrounding of cooker hood. If there are too many windows or a door nearby, it is advisable to close the windows and door before switching on the cooker hood to prevent the external air current from affecting the suction. The smoke has to rise up to 10in...

  • Page 7

    4. 風管膠帶 四.安裝步驟 1.請準備安裝位置及空間。 2.測量出風口及電源線孔的大小，然 後再鑽孔。 3.櫥櫃需加強本機固定的地方，建議 使用木條強化在櫥櫃內底部。 4.請先卸下不鏽鋼濾網，再用十字起 子移除兩側修飾板，並取下不鏽鋼 油杯。 5.依安裝位置設置四支木螺釘。 6.安裝時用木螺釘扣上之後，將油機 與櫥櫃用螺絲鎖緊，讓油機與櫥櫃 安全不會掉落。 7.裝設電源。 8.安裝風管並用風管膠帶密封。 9.檢查風管處是否緊密及其他功能是 否正常。 10.依序將不鏽鋼油杯、修飾板及不鏽 鋼濾網重新安裝回去。 櫥櫃安裝說明:(如圖一) 不鏽鋼濾網 與修飾板 油杯 圖一 電源線孔 木條 木螺釘與...

  • Page 8

    V. Venting instruction side wall cap w/gravity damper cabinet soffit or crawl space side wall cap w/gravity damper roof pitch w/ flashing & cap warning fire hazard some ducting options never exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All e...

  • Page 9

    6. 6. Vi. Installation air outlet by default the pr830/836as is pre-configured for 6" round vertical ducting. 1. Using a philips-head screwdriver remove the screws and 6" round vertical transition adapter from top of hood body. 2.Replace 6" round vertical transition adapter with rectangular transiti...

  • Page 10

    7 . 7. 5. Replace 6" round vertical transition adapter with rectangular transition adapter. Do not secure to hood body yet. 7. Place 3-1/4"x10" rectangular collar on back of hood and secure using the screws that previously secured the rectangular cover plate. 6. Place 3-1/4"x10" rectangular cover pl...

  • Page 11

    8. 8. Rotate knob to change light settings,(1) for dim light and (2) for bright light. Rotate knob to change speed levels,(1) for low speed, (2) for medium speed and,(3) for high speed. 1. Blower on/off/speed selection: 2. Lights dim/bright/off: 1.馬達開關及風速調整: 以旋轉旋鈕調整風速:(1)低速 (2)中速 (3)高速。 以旋轉旋鈕調整燈光亮度:...

  • Page 12

    9. 9. Halogen light: when the range hood is activated or has been running for a long time, be careful when handling the light bulb as it may be too hot to handle. Please double check to make sure the power supply to the range hood is shut off and the light bulb is cool before removing it. Remove the...

  • Page 13

    10. 10. A. Surface maintenance b. Surface cleaning and maintenance 1. Please clean the range hood surface regularly with warm soapy water and wipe with a cotton cloth to prevent grease from accumulating. 2. Please do not use harsh cleansers or coarse material to clean the surface because that will d...

  • Page 14

    11. 11. 十.排除故障 issue cause what to do after installation, the unit doesn’t work. 1. The power source is not turned on. 1. Make sure the circuit breaker and the unit’s power is on. 2. The power line and the cable locking connector is not connecting properly. 2. Check the power connection with the uni...