Panasonic DMPBDT100 - 3D BLU-RAY DISC PLAYER Operating Instructions Manual - page 13
Downloaded from www.vandenborre.be
13
VQT2U34
ENGL
IS
H
Search for access point:
Available Wireless routers (Access points) are searched and
listed. You can select the one to use from the list.
1 Press [
3, 4] to select SSID*
2
of Wireless router
(Access point) you want to connect with. Then press
[OPTION] to show information of the selected router,
make a note of the authentication and encryption type.
≥ If you can not find the SSID*
2
, select “Search again”.
2 Press [RETURN] and then press [OK].
Then select an item on the following screen which
corresponds to the authentication type noted down in
step 1 above.
Follow the on-screen instructions to make the settings.
≥ Input your encryption key code in “Encryption Key”
supplied with your Wireless router (Access point).
*1
Wi-Fi Protected Setup-compatible Wireless router (Access point) may
have the mark.
*2
An SSID (Service Set IDentification) is a name used by wireless LAN to
identify a particular network. Transmission is possible if the SSID
matches for both devices.
Access Point Connection Setting
Network Easy Setting (Connection Test)
When you experience
problems with settings
OK
Access Point Connection Setting
Reception
Select an access point to connect with.
To search for access point again, please
select "Search again" below.
SSID
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
Search again
SSID
Wireless type
Authentication type
Encryption type
:XXXXXXXXXXXXXXX
:802.11n/g/b (2.4GHz)
:WPA-PSK
:AES
Access Point Connection Setting
WPA2-PSK (AES/TKIP)
WPA-PSK (AES/TKIP)
Open/Shared Key (WEP)
Open system
Select authentication type.
OK
Access Point Connection Setting
Yes
No
Failed to connect to the access point.
A conflict with other devices occurred.
Do you wish to setup Access Point
Connection Setting again ?
Display
Check the following
A conflict with other
devices occurred.
≥ Please wait a few moments,
and then try again.
A time out error
occurred.
≥ Setting of the Wireless router
(Access point) for MAC Address
etc.
≥ The signal may be weak. Using
the USB extension cable
supplied with the Wireless LAN
Adaptor, adjust the position of
the Wireless LAN Adaptor.
≥ The SSID and the encryption
key of the Wireless router
(Access point).
≥ Please wait a few moments,
and then try again.
An authentication error
or a time out error
occurred.
A device error
occurred.
≥ Connection of Wireless LAN
Adaptor
If there is no improvement in
symptom, consult your dealer.
Display
Check the
following
1. LAN cable connection or
Connection to access point
:Fail
≥ Connection
of the LAN
cables
(> 11)
2. IP address setting
:Fail
3. Connection to gateway
:Fail
1. LAN cable connection or
Connection to access point
:Pass
≥ Connection
and settings
of the hub
and router
≥ Settings of
“IP Address /
DNS
Settings”
(> 31)
2. IP address setting
:Fail
3. Connection to gateway
:Fail
1. LAN cable connection or
Connection to access point
:Pass
2. IP address setting
:Home
network
available
3. Connection to gateway
:Fail
1. LAN cable connection or
Connection to access point
:Pass
2. IP address setting
:Pass
3. Connection to gateway
:Fail
OK
Network Easy Setting (Connection Test)
Yes
No
Complete.
1. LAN cable connection
2. IP address setting
3. Connection to gateway
LAN cable is not connected.
Please check the connection.
Select “Yes” and press [OK] to check network
connection again.
Select “No” and press [OK] to finish Network
Easy Setting.
: Fail
: Fail
: Fail
(13)
DMP-BDT100EG-VQT2U34.book 13 ページ 2010年6月22日 火曜日 午前11時0分