- DL manuals
- Panasonic
- All in One Printer
- DP-2330
- Service Manual
Panasonic DP-2330 Service Manual - Precautions
5
Precautions
Power and Ground Connection Cautions
Ensure that the plug connection is free of dust. In a damp environment, a contaminated
connector can draw a significant amount of current that can generate heat and eventually
cause fire if left unattended over an extended period of time.
Always use the power cord provided with your machine. When an extension power cord is
required, always use a properly rated cord.
120 V/15 A or AC 220 - 240V/10 A
If you use a cord with an unspecified current rating, the machine or plug may emit smoke or
become hot to the touch.
Do not attempt to repair, pull, bend, chafe or otherwise damage the power cord. Do not
place a heavy object on the cord. A damaged cord can cause fire or electric shocks.
Never touch a power cord with wet hands. Danger of electric shock exists.
If the power cord is damaged or insulated wires are exposed, contact the authorized
Panasonic dealer for a replacement. Using a damaged cord can cause fire or electric
Stop operation immediately if your machine emits smoke, excessive heat, unusual noise, or
abnormal smell, or if water is spilt onto the machine. These conditions can cause fire.
Immediately switch Off and unplug the machine, and contact the authorized Panasonic
.
Do not disconnect or reconnect the machine while the power switch is in the On position.
Disconnecting a live connector can cause arcing, consequently deforming the plug and
cause fire.
When disconnecting the machine, grasp the plug instead of the cord. Pulling on a cord
forcibly can damage it and cause fire or electric shock.
When the machine is not used over an extended period of time, switch it Off and unplug it.
If an unused machine is left connected to a power source for a long period, degraded insulation
can cause electric shocks, current leakage or fire.
Be sure to switch Off and unplug the machine before accessing the interior of the machine
for cleaning, maintenance or fault clearance. Access to a live machine's interior can cause
electric shock.
For Your Safety
To prevent severe injury and loss of life, read this section carefully before servicing the Panasonic
machine to ensure proper and safe operation of your machine.
This section explains the Warnings and Cautions used in the machine and/or this manual.
WARNING:
Denotes a potential hazard that could result in serious injury or death.
CAUTION:
Denotes hazards that could result in minor injury or damage to the machine.
This section also explains the Warnings and Cautions used in the machine and/or this manual.
These symbols are used to alert operators to a specific operating procedure
that must not be performed.
These symbols are used to alert operators to a specific operating procedure
that must be emphasized in order to operate the machine safely.
WARNING
Please ensure that the machine is installed near a wall outlet and is easily accessible.
shocks.
dealer.
Summary of DP-2330
Page 1
Order number: mgcs040801c0 h21 digital imaging systems dp-2310/3010 dp-2330/3030 [ version 2.1 ] this service information is designed for experienced repair technicians only and is not intended for use by the general public. It does not contain warnings or cautions to advise non-technical individual...
Page 2
2 the contents of this service manual and the specifications are subject to change without notice. Panasonic communications co., ltd. Reserves the right to make improvements in the product design without reservation and without notice. Published in japan. Information regarding lead-free (pbf) solder...
Page 3: Important Notice
3 important notice please read this notice completely before installing any optional accessories. As failure to properly install the additional board or connector with the power on (only the front power switch off) could damage the copier's spc or sc board. Please follow the instructions below: 1. I...
Page 4
4 hinweis:.
Page 5: Precautions
5 precautions power and ground connection cautions ensure that the plug connection is free of dust. In a damp environment, a contaminated connector can draw a significant amount of current that can generate heat and eventually cause fire if left unattended over an extended period of time. Always use...
Page 6
6 once a month, unplug the machine and check the power cord for the following. If you notice any unusual condition, contact the authorized panasonic dealer . The power cord is plugged firmly into the receptacle. The plug is not excessively heated, rusted, or bent. The plug and receptacle are free of...
Page 7
7 operating safeguards do not place a magnet near the safety switch of the machine. A magnet can activate the machine accidentally, resulting in injuries. Do not use a highly flammable spray or solvent near the machine. It can cause fire. When copying a thick document, do not use excessive force to ...
Page 8
8 memo.
Page 9
Table of contents 9 specifications table ............................ 11 1.1. Copy function.........................................11 1.2. Fax, printer and internet fax functions ................................................20 1.3. System combination...............................29 1.4. Options...
Page 10
Table of contents 10 8.15. Installing the expansion f-rom board (da-em600) ...............................317 8.16. Installing the sorting image memory 16 / 64 / 128 mb (da-sm16b / 64b / 28b).......................319 8.17. Installing the expansion flash memory card 4/8 mb (ue-410047/410048) ..........
Page 11: 1 Specifications Table
11 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 1 specifications table 1.1. Copy function items description remarks dp-2310/2330 dp-3010/3030 basic specifications 1 type desktop 2 platen fixed 3 original position platen left / rear adf / i-adf left / center 4 recording paper path center 5 face up / f...
Page 12
12 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 17 paper feed front loading universal paper tray paper tray capacity 550 sheets x 2 usa and canada ltr : 20 lb (75 g/m 2 ) other destinations a4 : 80 g/m 2 auto size setting no low level warning empty only bypass capacity 50 sheets auto size setting yes ...
Page 13
13 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 2 cabinet stand for 4-paper tray configuration option base plate with casters stand for 3-paper tray configuration option low plain stand stand for 2-paper tray configuration option high plain stand 3 platen cover option for eu and other destinations fr...
Page 14
14 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 tray position outer number of bins 1 face up / face down face down bin capacity 500 sheets ltr, ltr-r, a4, a4-r, b5 250 sheets ldr, lgl, a3, b4, fls multi tray function yes max. 3 way using optional exit tray (inner) and exit tray (outer) or finisher. Sh...
Page 15
15 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 15 hard disk drive option additional optional sorting image memory (minimum 16 mb) is required for the hard disk drive to function. (for tandem, remote copy, etc.) features 1 automatic features auto magnification selection yes auto paper selection yes a...
Page 16
16 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 2-sided copy yes inverse mode (negative / positive) yes centering mode yes with digital sky shot mirror mode no image repeat yes others (inverting adf & adu) 2-page copy mode yes ldr → ltr x 2 (a3 → a4 x 2, b4 → b5 x 2) 2 in 1 yes 4 in 1 yes 6 in 1 yes f...
Page 17
17 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 job complete notice yes trial copy mode yes weekly timer yes function mode yes interrupt yes electronic counter yes digital sky shot mode yes check / slip mode yes 3 control panel display wide touch panel lcd status lamp yes green : scanning / printing ...
Page 18
18 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 number of copies yes job build and sadf / multi size feed mode yes error code yes finishing yes warning indicators yes add toner yes toner waste container full yes add paper (no paper) yes add paper (under 50 sheets) no paper jam indication yes paper jam...
Page 19
19 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 adf 100% inverting adf 100% adu copy productivity (ltr / a4) throughput when exiting to lower inner tray from 1st tray. When lsu is ready. Transport method stack less 1 → 2 1 copy 70% 57% 5 copies 90% 80% 10 copies 95% 85% pm cycle 1 pm cycle major pm 1...
Page 20
20 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 1.2. Fax, printer and internet fax functions 1.2.1. Fax function items description remarks dp-2310/2330 dp-3010/3030 main specifications 1 compatibility g3 itu-t std & non-std 2 pstn line port yes 1-line only 3 leased line port no 4 v.24 line port no 5 m...
Page 21
21 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 5 effective scanning width ldr (11.5 in) / a3 (292 mm) 6 a3 size tx/rx yes conforms to itu-t a3 7 reduction xmt yes a3 to b4 / a3 to a4 / b4 to a4 8 adf capacity 50 sheets face-up, feed from top page 9 collation stack yes face down printer mechanism 1 r...
Page 22
22 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 7 full number dialing (buffered dialing) yes max. 70 stations 8 direct dialing (monitor dialing) yes voice mode 9 automatic redialing yes up to 15 times at 0 to 15 min. Intervals 10 manual redialing yes pressing the redial/pause button 11 line monitor sp...
Page 23
23 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 6 distinctive ring detector (drd) no 7 90 degree rotation reception yes 8 duplex printing yes polling 1 polling yes 2 turnaround polling no 3 multi-station polling yes max. 270 stations 4 deferred polling yes max. 50 timers 5 deferred multi-station poll...
Page 24
24 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 special communications 1 password xmt / rcv no 2 selective reception no tsi check 3 relay xmt request no 4 relay xmt center no 5 confidential xmt / polling no 6 confidential center no 7 mailbox xmt / polling no 8 mailbox center no 9 file xmt no 10 fax fo...
Page 25
25 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 1.2.2. Printer function items description remarks dp-2310/2330 dp-3010/3030 interface 1 centronics parallel i/f no 2 lan (network) ethernet 10base-t/ 100base-tx 3 usb port yes usb 4 ieee-1394 no printer function 1 printing size ldr, lgl, ltr, ltr-r, inv...
Page 26
26 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 1.2.3. Network scanner function items description remarks dp-2310/2330 dp-3010/3030 interface 1 centronics parallel i/f no 2 lan (network) ethernet 10base-t/ 100base-tx 3 usb port no 4 ieee-1394 no firewire network scanning function 1 scanning device ccd...
Page 27
27 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 1.2.4. Internet fax function items description remarks dp-2310/2330 dp-3010/3030 main specifications 1 communication protocols smtp / pop3 / mime 2 max. Modem speed na 3 coding scheme jbig/mmr/mr/mh 4 file format tiff / pdf selectable (pdf format can be...
Page 28
28 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 lan features 1 internet fax communication yes a3 communication is available with parameter setting. 2 internet mail reception yes 3 internet fax server features internet fax relay xmt yes internet fax → internet fax → g3fax email relay mxt yes pc → inter...
Page 29
29 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 1.3. System combination document sensor motor scanner unit (sdr pc board) expansion flash memory card 4 or 8m main pc board (sc pc board) image memory either option electronic sorting memory dual-path exit guide unit paper transport unit 2nd paper tray ...
Page 30
30 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 1.4. Options list ■ options option name option number remarks printer controller module for pcl6 da-pc300 for dp-2310 / 3010 multi page description language controller module for ps/pcl6 da-mc300 printer controller module for pcl6-ipx/ spx da-pc301 for d...
Page 31
31 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 ■ supplies note: pcl6 is a page description language of the hewlett-packard company. Ps3 is a page description language of the adobe systems company. Available in specified destinations part name part number remarks toner dq-tu15e 15 k staple cartridge ...
Page 32
32 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 1.5. External view 1. Standard configuration 2. With optional system console configuration 33.86 in (860 mm) 27.44 in (697 mm) 23.58 in (599 mm) 27.83 in (707 mm) manufacturer's name and address factory id product complies with dhhs rules 21 cfr subchapt...
Page 33
33 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 3. Space requirements with options 27.83 in (707 mm) 27.83 in (707 mm) 27.83 in (707 mm) 14.2 in (379 mm) 14.92 in (379 mm) 14.92 in (379 mm) copier + finisher copier + outer exit tray copier 3.94 in (100 mm) 3.94 in (100 mm) 10.83 in (275 mm) 14.84 in ...
Page 34
34 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 1.5.1. Serial number contents the contents of the 11-digit serial number is as follows: 2 3 4 5 6 1 sequential production number 5-digit sequential production number 00001 ~ 99999 = 1 ~ 99,999 units a0001 ~ y9999 = 100,000 ~ 329,976 units (letters “i” an...
Page 35
35 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 1.6. Control panel dp-2310/3010 dp-2330/3030
Page 36
36 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 1.7. Fans and motors 1.8. Clutches and switches scanning motor (201) lvps fan (322) lsu fan (315) main motor (907) adf motor (1801) transport motor (1320) toner motor (958) lift dc motor (1152) fan (459) ils pcb (19124) (front cover sensor) paper feed ro...
Page 37
37 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 1.9. Pc boards cst2 pcb (1913) dcb pcb (1906) hsu pcb (1974) lvps (1910) optional lvps (1912) nfl pcb (1909) rlb pcb (1917) acd pcb (1904) adf pcb (1907) pnl3 pcb (113) exfd pcb (1978) mjr pcb (1915) dc pcb (1905) fxb pcb (1916) sdr pcb (1903) pnl2 pcb ...
Page 38: 2 Disassembly Instructions
38 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 2 disassembly instructions 2.1. General disassembly pertinent disassembly instruction sections are shown below..
Page 39
39 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 2.2. Disassembly instructions 2.2.1. Inverting-automatic document feeder (i-adf) unit (1) open the adf cover (1831). (2) remove 4 silver screws (b1). (3) lift the adf input tray (1604). (4) slightly pull the right edge of the adf rear cover upward. (5) ...
Page 40
40 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (15) remove the snap ring (s9). (16) remove the pin (744). (17) remove the adf shaft (1724). (18) remove the adf roller (1728). (19) remove the snap ring (s9). (20) remove the pre-feed roller shaft (1730). (21) remove the pre-feed roller (1731). (22) rem...
Page 41
41 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (30) disconnect all connectors on the adf pc board. (31) remove 2 screws (19). (32) remove the adf pc board (1907). (33) remove 2 screws (24). (34) remove the adf motor (1801). (35) remove 6 screws (19). (36) remove the sensor bracket (1663). (37) remov...
Page 42
42 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 roller and feed 2 roller> (1) open the adf cover (1831). (2) clean the adf roller (1728), pre-feed roller (1731), drive roller (1872) and the feed 2 roller (1753) with a soft cloth, saturated with isopropyl alcohol. (3) lift the adf input tray (1604). (4...
Page 43
43 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 2.2.2. Control panel unit (1) pull the battery holder (104) part of the way out. (2) release the latch and remove the battery holder (104) out. (3) remove 6 silver screws (b1). (4) remove the left platen cover (514) and the right platen cover (516). (5)...
Page 44
44 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (11) remove 4 screws (f10). (12) remove the pnl1 pc board (1908). (13) remove 7 screws (f10). (14) disconnect the harness on the pnl2 pc board (cn251). (15) remove the pnl2 pc board (123). Note: after reassembling the control pnl2 pc board, make sure tha...
Page 45
45 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (21) remove 1 screw (p5). (22) remove the pnl4 pc board (114). (23) remove 4 screws (p5). (24) remove the pnl3 pc board (113). (25) remove 2 screws (h4). (26) remove 2 screws (h4). (27) remove the lcd module (128). (28) remove the touch panel (127)..
Page 46
46 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 2.2.3. Scanner unit (1) remove the left and right platen covers (514, 516) and the control panel assembly. (refer to 2.2.2.) (2) remove 2 screws (19). (3) remove the glass assembly (557). (4) remove the glass s (559). (5) holding by the center, slowly mo...
Page 47
47 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (8) remove 2 screws (19). (9) remove the 2 lamp plate springs (232). (10) disconnect the harness on the lfb pc board (cn181). (11) remove the scanning lamp (204). (12) remove 2 mirror plate springs (230). (13) remove mirror 1 (264). Note: observe the po...
Page 48
48 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (19) remove 2 red screws (d24). (20) remove the fpc cable holder a (215) assembly. (21) holding by the center, slowly move the lamp base assembly towards the left of the scanner base frame. (22) disconnect the harness on the lfb pc board (cn181). (23) re...
Page 49
49 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (31) remove the e-ring (5y). (32) remove the synchro belt (208). (33) remove the mxl34 pulley (217). (34) remove 1 screw (6p). (35) remove the fan (459). (36) disconnect the harness on the scanning motor. (37) remove 3 screws (19). (38) remove the motor...
Page 50
50 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (41) disconnect the harness on the sc pc board (cn106). (42) release 2 latch clips and remove the ferrite core. (43) remove 3 red screws (d24). (44) remove the ccd assembly (207). Note: when reinstalling the ccd assembly, align the hole with the red mark...
Page 51
51 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (47) remove 2 screws (19). (48) remove the sdr pc board (1903). (49) remove 6 screws (19). (50) remove the f/r scanner frame (240). (51) remove 2 red screws (d24). (52) remove the rear lamp belt lock (228). (53) remove the front lamp belt lock (227). (5...
Page 52
52 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (56) remove 2 screws (18). (57) remove the rear mirror belt lock (238). (58) remove the front mirror belt lock (236). (59) remove the mirror 2 bracket (233) assembly. (60) remove the 4 mirror 2 plate springs (206). (61) remove the two mirror 2 (265). (62...
Page 53
53 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (3) install the mirror 2 bracket (233) assembly. (4) reinstall the 2 inner timing belts (202). Note: the bracket must be adjusted by moving it towards the center until it stops against the notches in the frame. (5) while holding each side of the bracket...
Page 54
54 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (8) clean the mirror 1 (264) and both the mirror 2 (265) with a soft cloth, saturated with isopropyl alcohol..
Page 55
55 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 2.2.4. Process unit (1) open the right cover (1201). (2) remove 1 screw (6p). (3) remove the harness cover (1525). (4) unlock the angled rear arm (1218) and the front arm (1217). (5) open the right cover and hook the angled rear arm into the lower hook ...
Page 56
56 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (11) disconnect the harness. (12) loosen the process unit screw (743). (13) slide the process unit out. Caution: to prevent damage to the process unit, ensure the right cover is still open before pulling the process unit out. Caution: exercise caution no...
Page 57
57 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (19) remove the harness from clamp, disconnect the connector. (20) remove 2 screws (51) and 1 snap ring (g6). (21) remove the hopper unit. Note: when reinstalling the hopper unit, insert the hooks into the recessed holes on the developer unit as illustr...
Page 58
58 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (26) shake the developer bottle thoroughly (approx. 30 seconds). (27) pour the appropriate developer evenly into the developer unit. Make sure to empty the bottle. (28) close the developer cover. Note: when reinstalling the developer cover, ensure that 2...
Page 59
59 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (33) remove the cleaning roller (706). (34) remove 2 bias charge roller holder (728) assemblies. Note: when reinstalling the bias charge roller holder assembly on the rear side, install the bias charge roller holder (728) first and then the bias charge ...
Page 60
60 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 2.2.5. Fuser unit caution: to prevent from getting burned, do not install, remove, clean or make adjustments when the fuser unit is hot. (1) open the right cover (1201). (2) remove 1 screw (6p). (3) remove the harness cover (1525). (4) unlock the angled ...
Page 61
61 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (10) disconnect 2 harnesses. (11) remove 4 screws (4n). (12) remove the fuser unit. (13) remove 4 screws (6p). (14) remove the dual-path exit guide. (15) clean the feed roller (1510) with a soft cloth, saturated with isopropyl alcohol. (16) clean the fe...
Page 62
62 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (17) remove 3 screws (4n). (18) remove the lower fuser cover (1003). (19) remove 2 screws (21). (20) disconnect the harness. (21) remove the cleaning web roller unit. (22) remove 1 screw (21). (23) remove the rear web bracket (1071). (24) remove the clea...
Page 63
63 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (31) remove 3 screws (23). (32) remove 2 screws (19). (33) remove the harness guide (1004). (34) remove 1 screw (21). (35) remove the rear lamp holder (1021). (36) remove 2 screws (16). (37) remove 1 screw (21). (38) remove the front lamp holder (1018)..
Page 64
64 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (39) remove 2 fuser lamps (1043 and 1044). Note: make sure to check the wattage of each fuser lamp when replacing. Note: 1. When reinstalling, route the harnesses along the hooks as illustrated. 2. Be sure to install the longer harness to the gear side a...
Page 65
65 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (42) remove the fuser roller (1026) assembly. (43) remove the 2 c-rings (1078). (44) remove the e40 heat roller gear (1014). (45) remove the plate spacer (1023). (46) remove the 2 insulation bushings (1006). (47) remove the 2 bearings (1046). Note: 1. T...
Page 66
66 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (51) remove the exit roller (1028). (52) remove the turn guide (1007). (53) remove 1 screw (19). (54) remove the upper guide (1001). (55) remove 5 upper fingers (1067). (56) remove the pressure roller (1027)..
Page 67
67 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (57) remove 2 bearings (1039). Note: 1. When reinstalling, make sure to install with bearing's retainer ring facing towards the roller. 2. Do not scratch the surface of the pressure roller when removing or reinstalling it. Clean the surface of the press...
Page 68
68 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 2.2.6. Drive unit (1) remove 4 silver screws (s6). (2) open the rear cover (302). (3) remove 4 silver screws (s6). (4) remove the rear right cover (507) and the right rear cover (518). (5) remove 2 silver screws (b1). (6) remove the lower rear cover (506...
Page 69
69 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (12) disconnect the mt harness (1926) on the main motor (cn1 and cn2). (13) remove 5 screws (4n). (14) remove the main motor (907). (15) disconnect the connector on each of the 3 clutches. (16) remove 3 snap rings (s9). (17) remove 3 clutches (969, 1105...
Page 70
70 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (23) remove 3 screws (19). (24) remove the motor bracket (908)..
Page 71
71 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 2.2.7. Right cover (1) open the right cover (1201). (2) remove 1 screw (6p). (3) remove the harness cover (1525). (4) unlock the angled rear arm (1218) and the front arm (1217). (5) hook the angled rear arm (1218) into the lower hook hole. Clean the sen...
Page 72
72 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (11) remove 1 screw (19). (12) remove the registration pinch roller (1222). Clean the surface of the registration pinch roller with a soft cloth, saturated with isopropyl alcohol. (13) remove the roller cleaner (1229). Note: when installing the roller cl...
Page 73
73 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (16) remove the btr gear (1234). (17) remove the bias transfer roller (1221). Clean the surface of the bias transfer roller only with a soft dry cloth..
Page 74
74 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 2.2.8. Sheet bypass (1) remove 1 screw (19). (2) remove 1 screw (1y). (3) remove the snap ring (s9). (4) remove the p6l5 conductive bushing (972). (5) remove the dual-path guide (1203). (6) remove 1 screw (19). (7) remove the feed roller (1244). Clean th...
Page 75
75 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (10) remove 1 screw (x6). (11) remove the reverse roller guide (1294). (12) remove the reverse roller (1291) assembly. (13) remove the bushing (1286). (14) remove the washer (1288). (15) remove the e-ring (j7). (16) remove the reverse roller (1291). Cle...
Page 76
76 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 2.2.9. Paper feed module (1) remove the process unit. (refer to 2.2.4.) (2) remove the clutch (1105). (refer to 2.2.6.) (3) remove the snap ring (s9). (4) remove the registration roller (1121). Clean the surface of the registration roller with a soft clo...
Page 77
77 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (11) remove the reverse clutch (1132) and spring d (1178). (12) remove the c25 gear roller (1145). Clean the surface of the c25 gear roller with a soft cloth, saturated with isopropyl alcohol. (13) slide the 2nd paper tray out. (14) open the jam access ...
Page 78
78 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 2.2.10. Lsu unit (1) remove the process unit. (refer to 2.2.4.) (2) slide the 1st paper tray out. (3) remove 1 screw (19) and 2 screws (6p). (4) remove the front left cover (534). (5) remove the blind cover (530). (6) remove 2 screws (s6). (7) remove the...
Page 79
79 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 2.2.11. Paper transport unit (1) remove the inner tray (1522). (2) push open the paper transport jam cover (1302). (3) clean 6 pinch rollers (1518) with a soft cloth, saturated with isopropyl alcohol..
Page 80
80 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 2.2.12. Pc board (1) remove 7 screws (6p). (2) disconnect all the harnesses on the sc pc board. (3) remove the sc pc board (1901). (4) remove 3 screws (6p). (5) disconnect all the harnesses on the spc pc board. (6) remove the spc pc board (1902). (7) rem...
Page 81
81 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (10) remove 6 screws (6p). (11) disconnect all the harnesses on the acd pc board. (12) remove the acd pc board (1904). (13) remove 2 screws (6p). (14) disconnect all the harnesses on the dc pc board. (15) remove the dc pc board (1905). (16) remove 9 scr...
Page 82
82 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 2.3. Screw identification template * for dp-2330/3030 part no. Figure remark ref. No. Dzpa000094 dzpa000088 743 shoulder screw dzpa000025 1033 washer xwg55e12fy 1052 xtb3+8j 19 xtb3+8jfj xyn3+f8 23 xyn3+f8fj xtb3+6f 21 xtb3+6ffj xtb3+8f 20 xtb3+8ffj xyn3...
Page 83
83 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 part no. Figure remark ref. No. Screw dzpb000020 c2 silver screw dzpb000007 b1 xtw3+10s e8 xtw3+8sfc c8 xtw3+8sfj xtw3+6lfc 6p xtw3+6lfj xtb26+6j 7b xtb26+6jfj xsn3+w8fc 4n xtw3+10sfj xsn3+w8fj screw screw screw screw screw xtb3+32j e5 xtb3+24j e6 blue ...
Page 84
84 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 part no. Figure remark ref. No. Screw xtn3+10g f9 silver screw xsn4+w10fn f7 screw dzpa000063 f4 washer dzpk000021 f6 snap ring ffpfj0039b g6 e-ring xuc3vm j6 e-ring xuc4vm j7 e-ring xuc7vm j8 snap ring ffpfj0033b h6 snap ring ffpfj0041b h7 xtb3+8g f10 x...
Page 85
85 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 part no. Figure remark ref. No. Screw dzpa000086 s6 screw ffpfa0152 p7 screw xtn3+8g p5 snap ring dzjm000171 s9 silver screw xtw3+10lfn v4 screw dzpa000087 t2 screw xtb3+12j p2 xtb3+12jfj tumb screw dzpa000064 m2 screw b3x6tts-rp p1 xtb3+6ffj-rp red scr...
Page 86
86 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 3 maintenance, adjustments and check points 3.1. Preventive maintenance preventive maintenance is performed at specific intervals and consists of machine cleaning and parts replacement. It is essential to perform these service activities properly and at ...
Page 87
87 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 4 laser handling precautions the optical laser system employed by this photocopier is completely sealed by a protective housing and an external cover. Therefore, the laser beam will not stray or leak during photocopying operation. However, when servicin...
Page 88
88 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 3.2. Required tools 3.2.1. Preventive maintenance method no. Tools no. Tools 1 soft cloth 7 pliers 2 isopropyl alcohol 8 cotton swab 3 phillips screwdriver (#2) 9 brush 4 stubby phillips screwdriver (#2) 10 ks-660 - conductive grease (available from shin...
Page 89
89 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 3.3. Preventive maintenance points 5 7 7 6 47 8 11 20 45 46 45 21 44 43 43 detail b 16 18 13 17 12 14 15 19 13 12 14 15 12 14 12 14 10 4 3 1 2 9 47 detail a.
Page 90
90 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 detail a detail b 25 29 24 26 27 28 23 22 42 32 40 34 33 30 31 38 37 35 36 41.
Page 91
91 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 3.4. Preventive maintenance check list no. Mechanical parts ref. No. Cleaning replacement/adjustment ref. Counter cycle (sheet) method cycle (sheet) procedure i-adf/adf unit 1 adf roller 1728 60k alcohol 120k refer to 2.2.1. F7-02-03 2 pre feed roller 1...
Page 92
92 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 note: 1. Wet cloth represents a soft cloth saturated with water. 2. The maintenance cycle is based on the counter information for each individual module. To verify the counter information, print the total counter list using the service mode: f7 - electro...
Page 93
93 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 3.5. Resetting the p/m (preventive maintenance) counter when the machine reaches the preset p/m cycle, it will show "call for p/m" or "replace the toner waste container" on the lcd display. The pm counter can be reset by following the procedures below. ...
Page 94
94 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 3.6. Lubrication point list this information is used for routine preventive maintenance (pm) calls to ensure the highest degree of reliability. Inspect the following areas and lubricate as required. The inspection interval is usually 120k copies or more,...
Page 95
95 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 idle roller plate spring 1509 em-50l idle roller 1511 roller shaft 1313 em-50l pinch roller 1518 paper transportation drive roller 1314 em-50l p6l8 bushing 1322 roller shaft 1313 em-50l pinch roller 1518 mechanical parts ref. No. Grease lubrication poin...
Page 96
96 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 automatic duplex unit bias transfer roller (btr) 1221 em-50l ks-660 registration pinch roller 1222 front bushing 1231 rear bushing 1233 roller shaft 1313 em-50l pinch roller 1518 drive roller 1409 em-50l p6l5 bushing 1150 pinch spring 1411 em-50l pinch r...
Page 97
97 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 3.7. Updating the firmware the quickest and most easiest method of updating the firmware is to use the network firmware tool (fup) using ethernet lan port and a crossover cable. The network fup tool version must be 3.Xx or higher, and it can be found on...
Page 98
98 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (2) for pcl option the pcl control program (2) must be written into the 4 mb onboard, which is assigned as rom code (b). The pcl control program (3) and pcl font data (4) are written into the 8 mb in the slot 1. The firmware (3) and (4) are assigned as r...
Page 99
99 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 3.7.2. Updating through a lan port (the quickest and most easiest method) the firmware code can be easily updated when the main unit is connected to a lan. The network firmware update tool can also be used by connecting to the machine using a crossover ...
Page 100
100 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 note: 1. Manual mode must be used, when updating the designated version of the firmware or changing the type of the firmware. Please refer to the section 2.2, "setting up the network firmware update tool, file selection tab" of the operating instruction...
Page 101
101 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 3) preparing the main unit for the firmware upgrade important: do not connect the usb cable yet. Print the f5/f6 parameters list (copier service mode f9-03-00). Enter into test mode f9-07-01 to enable the unit to accept the programming code from the us...
Page 102
102 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 3.7.4. Updating the firmware using the master firmware card (alternate method) 1. Before starting, print the f5/f6 parameters list (copy service mode f9-03-00). 2. Turn the power switch on the left side and the main power switch on the back of the machi...
Page 103
103 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 off position. (see 3.7.7.) 2. Insert the flash memory card (4 mb or 8 mb) into the machine. 3. Turn the main power switch on the back and the power switch on the left side of the machine to the on position. 4. Press the "function", "original size (ledg...
Page 104
104 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 3.7.7. Notice after installing the hdd option after the hard disc drive unit is installed, to prevent a disc scan function from being performed (similar to windows os when the power is abruptly interrupted), it is important to follow the step sequence b...
Page 105
105 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 3.7.9. Firmware version dp-2310/3010 sc : pnl : dp-sfdl2 a a vxxxxx pu destination code (copier) pu : usa/canada pb : uk destination code (fax) au : usa/canada ab : uk firmware version (v1xxxx) language code a : a-english, c-french & spanish b : a-engl...
Page 106
106 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 dp-2330/3030 spc : sc : sfdl2 spc a a vxxxxx firmware version (v1xxxx) aa: fixed spc model number sfd l25r a a vxxxxx pu destination code (copier) pu : usa/canada pb : uk destination code (fax) au : usa/canada ab : uk firmware version (v1xxxx) language ...
Page 107
107 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 pnl : spc : l25r pnl a a vxxxxx pu destination code (copier) pu : usa/canada pb : uk destination code (fax) au : usa/canada ab : uk firmware version (v1xxxx) language code a : a-english, c-french & spanish b : a-english, spanish,german, french & italia...
Page 108
108 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 3.8. Adjusting the printer registration, lsu image side to side when installing the paper tray option, the following lsu image side to side adjustment must be performed. The printer registration is adjusted at the factory. If copy image is abnormal, spe...
Page 109
109 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 5. Perform the service mode f6-16 (adu side adjust), to adjust the gap to be 5 mm. 6. If the gap is less than 5 mm, input a (+) value. If more than 5 mm, input a (-) value. 7. Press "stop" first and then press "function" + "clear" keys simultaneously t...
Page 110
110 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 standby. Note: this is the size adjustment and do not worry about the positioning. 3.8.7. Adf original read edge & adf main scan adjustments 1. Place the original document on the adf. 2. Insert ledger or a3 size paper into the 1st tray and change the tr...
Page 111: 4 Troubleshooting
111 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 4 troubleshooting 4.1. Initial troubleshooting flowchart start plug the power cord in and turn the power switches on. Does the lcd display the function correctly? Does the original document feed through correctly? Does the recording paper exit the unit...
Page 112
112 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 4.2. Improper lcd display replace the sc pcb. Is the trouble resolved? Replace the low voltage power supply unit. Is the trouble resolved? Check connectors: cn52 (sc pcb) and cn220 (pnl1 pcb). Is led/lcd displayed? Does the display appear normal? Replac...
Page 113
113 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 4.3. Printed copy quality problems 4.3.1. Black copy start yes no check the scanner mechanism. Is the ps normal? Is the spc pcb normal? Is the opc drum/developer unit operational? Replace the opc drum/developer unit. 1. Check all connectors and voltage...
Page 114
114 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 4.3.2. Blank copy start end check the scanner mechanism. Are there any foreign particles or stains in the charge unit? Is the opc drum/developer unit operational? Is the ps normal? No yes yes yes no no replace the opc drum/developer unit. Yes no 1. Clea...
Page 115
115 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 4.3.3. Vertical white lines start end replace the recording paper. Yes no replace the drum/developer unit. Are there any foreign particles or stains blocking the laser beam path? No yes no clean or replace the rollers. Yes no check the scanner mechanis...
Page 116
116 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 4.3.4. Ghost images start end yes no check the scanner mechanism. Is the opc drum/developer unit operational? No yes are the fuser and pressure roller surfaces clean? Is the recording paper damp? No yes yes no replace the recording paper. Replace the op...
Page 117
117 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 4.3.5. Vertical dark lines start yes no check the scanner mechanism. Is the opc drum/developer unit operational? Yes no replace the opc drum/developer unit. Is the lsu normal? No yes replace the lsu. End no yes clean or replace the rollers. Paper trave...
Page 118
118 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 4.3.6. Horizontal dark lines start yes no replace the opc drum/developer unit. Yes no check the scanner mechanism. Is the opc drum/developer unit operational? Is the lsu normal? Yes replace the lsu. Is the ps normal? 1. Check all connectors and voltages...
Page 119
119 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 4.3.7. Dark background is the lsu normal? No yes replace the lsu. Start yes no check the scanner mechanism. Is the opc drum/developer unit operational? No yes is the recording paper damp? Yes no replace the recording paper. Replace the opc drum/develop...
Page 120
120 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 4.3.8. Light print end no yes start yes no is the test pattern printout in copier f1 mode or fax service mode 3 normal? Check the scanner mechanism. No yes is the opc drum/developer unit operational? Is the recording paper damp? Yes no replace the paper...
Page 121
121 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 4.3.9. Horizontal white lines end no yes clean or replace the rollers. Start yes no check the scanner mechanism. Is the opc drum/developer unit operational? No yes is the recording paper damp? Yes no replace the recording paper. Replace the opc drum/de...
Page 122
122 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 4.3.10. Improper fusing (printed image does not bond to the paper) note: replace the entire fuser unit when the thermostat and/or the thermistor fail (open-circuit). End is the fuser unit normal? No yes replace the fuser unit. (see note) start no yes is...
Page 123
123 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 4.3.11. Voids in solid areas 4.3.12. Black dots end no yes clean or replace the rollers. Start no yes is the recording paper damp? Replace the recording paper. Is the opc drum/developer unit operational? Yes no replace the opc drum/developer unit. P pa...
Page 124
124 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 4.3.13. Recording paper creases start no yes is the recording paper damp? Replace the recording paper. End are the fuser and pressure roller surfaces soiled or are there any foreign particles or stains in the fuser unit? 2. Clean or replace the rollers....
Page 125
125 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 4.3.14. Poor printed copy quality start is the test pattern printout in copier f1 mode or fax service mode 3 normal? 1. Replace the spc pcb. 2. Replace the lsu. 3. Replace the ps. 4. Replace the developer unit. End perform a receiving test with the ref...
Page 126
126 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 4.3.15. Document skewing end start is the lsu normal? Check the scanner or adf/iadf mechanism. Check or replace lsu. No no yes yes is the test pattern printout in copier f1 mode normal? Copy mode sample.
Page 127
127 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 4.3.15.1. Lsu skew adjustment (1) open the front cover and the right cover. (2) slide the process unit out. (refer to 2.2.4.) caution: exercise caution not to scratch the surface of the opc drum (green), and not to touch it with bare hands. (3) remove ...
Page 128
128 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 4.3.16. Abnormal printing start is the recording paper loaded in the paper tray properly? 1. Adjust the paper width guide. 2. Adjust the paper length guide. Is the panasonic toner being used? Yes no is the recording paper size and thickness within speci...
Page 129
129 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 4.3.17. Scanned copy quality problems start no yes is the scanning lamp abnormal? Replace the scanning lamp. End are the transmitting rollers dirty? Are there any foreign particles or paper pieces in the scanning area? Yes no remove the foreign particl...
Page 130
130 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 4.3.18. Print skew adjustment for platen glass scanning follow the procedures below to adjust for the skewing when scanning original(s) from the platen glass. (1) make sure that the scanner unit is in the standby mode. (2) remove 3 screws and the left p...
Page 131
131 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 4.4. Document feeder (adf) 4.4.1. No document feed is the document set properly? Adjust or replace the actuator. Is the document thickness or size within specifications? Does the lcd activate when a doument is set? Check the harness of the adf motor. D...
Page 132
132 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 4.4.2. Document jam remove any obstacles blocking the path. Is the trouble resolved? Is the trouble resolved? Are there any obstacles in the document path? Does the adf roller rotate? Check the adf motor connector. Replace the adf motor or the adf pcb. ...
Page 133
133 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 4.4.3. Document skew remove any obstacles from the document path. Are there any obstacles in the document path? Are the components of the feeder unit operational? Does the np sensor actuator move smoothly? Are the pre-feed and adf rollers operational? ...
Page 134
134 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 4.4.3.1. Adf / i-adf feed skew adjustment 1. Front page skew adjustment using a lined original (about 20 lb (80 g/m 2 ) weight pager), make a copy from the adf / i-adf to check for feeding alignment. Adjust the feed skew adjustment "a" downwards and rec...
Page 135
135 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 2. Back page skew adjustment (i-adf only) using a lined original (about 20 lb (80 g/m 2 ) weight pager), make a copy from the i-adf to check for feeding alignment. 4.4.4. Adf / i-adf free stop adjustment follow the procedure below to adjust the free st...
Page 136
136 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 4.5. Troubleshooting the lan interface 4.5.1. Checking network configuration start from the dos prompt, enter the following command-line utility: ipconfig /all locate a pc connected to the same subnet mask as the unit does the displayed network configur...
Page 137
137 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 4.5.2. Testing the tcp/ip network it is beyond the scope of this service manual to cover networking in detail, there are many excellent manuals on this subject, but we hope the information in this section will aid with your troubleshooting efforts. In ...
Page 138
138 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 2. Checking current configuration print the current unit internet parameters configuration. Locate a pc connected to the same subnet mask as the unit, then from the dos prompt, type the following command-line utility: "ipconfig /all" for windows 98/me/2...
Page 139
139 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 pinging the unit pinging the default gateway (default router ip address) pinging the smtp/pop server if for some reason, the physical connection is missing, the echo reply will not be received from the destination and the following output is displayed:...
Page 140
140 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 if the physical destination is far and it's connected by wan (wide area network), the ping option command default value must be changed to compensate for the expected delayed response. E.G. 4. Tracing a packet route another useful command-line utility i...
Page 141
141 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 5. Managing network route tables in the simplest case a router connects two network segments. In this model, the system used to join the two segments needs to know only about these segments. The routing table for router r1 in this case is simple; the f...
Page 142
142 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 when the packet does not reach the specified destination even when the physical connection is properly made, check the registered persistent routes on the same subnet as the unit by typing "route print" in the dos command-line. The output display is sho...
Page 143
143 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 7. Testing unit using the telnet command telnet is a terminal emulation protocol. Telnet enables pcs and workstations to function as dumb terminals in sessions with hosts on internet works. From windows 98/me/2000/nt/xp, use the telnet to test the comm...
Page 144
144 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 4.6. Error codes (for copier) the self-diagnostic functions detect troubles in the important components of the copier. When any trouble occurs, the copier stops. 4.6.1. User error codes (u code) note: uxx and a message will appear on the panel display. ...
Page 145
145 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 u13 add toner 1. Toner bottle incorrectly installed. 2. Low toner. 3. Toner sensor disconnected. 4. Toner sensor defective. 5. Spc pcb connector disconnected. 6. Spc pcb defective. U14 replace toner waste container 1. Toner waste container full. (see s...
Page 146
146 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 4.6.2. Jam error codes (j code) • j code log view mode the 5 most recent j codes can be displayed on the panel display by pressing "function" and "3" keys in standby mode. Note: if the machine is jammed, follow the procedure below. 1. Turn the power swi...
Page 147
147 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 • jam sensor location of printer 2nd paper tray sheet bypass automatic duplex unit sensor 4 automatic duplex unit sensor 3 automatic duplex unit sensor 1 registration sensor 2nd registration sensor 3rd registration sensor 4th registration sensor automa...
Page 148
148 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 • jam sensor location of finisher • jam sensor location of i-adf • jam sensor location of adf finisher registration sensor finisher exit sensor stapler eject sensor duplex eject sensor read point sensor original detection sensor eject sensor read point ...
Page 149
149 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 jam error codes (j code) table code contents section j00 the registration sensor does not detect paper within a predetermined time after the paper starts feeding. (sheet bypass) c j01 the registration sensor does not detect paper within a predetermined...
Page 150
150 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 j48 the dual-path exit sensor does not detect paper within a predetermined time after the fuser unit paper exit sensor is activated. C j51 the paper transport unit sensor 2 does not detect paper within a predetermined time after eject paper sensor of du...
Page 151
151 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 dp-2330/ 3030 dp-2310/ 3010 contents section j70 j70 read point sensor does not detect paper within a predetermined time in the adf. (information code 030 is printed on the transaction journal instead.) e j71 j71 read point sensor keeps detections pape...
Page 152
152 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 4.6.3. Mechanical error codes (e code) e1: optical unit error code function possible cause(s) e1- 01 abnormal platen glass scanning 1. Home position sensor connector disconnected. 2. Home position sensor defective. 3. Scanner motor connector disconnecte...
Page 153
153 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 e2: lift dc motor error code function possible cause(s) e2- 01 lift motor rotation (1st paper tray) 1. Level sensor connector disconnected. 2. Level sensor defective. 3. Lift mechanism defective. 4. Lift motor connector disconnected. 5. Lift motor defe...
Page 154
154 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 e3: development system error code function possible cause(s) e3- 01 toner bottle motor rotation 1. Toner bottle motor connector disconnected. 2. Toner bottle motor defective. 3. Toner bottle motor drive mechanism defective. 4. Toner bottle installed inc...
Page 155
155 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 e4- 10 fuser fan motor rotation 1. Fuser fan connector disconnected. 2. Fuser fan defective. 3. Spc pcb connector disconnected. 4. Spc pcb defective. 5. Lvps defective. E5: system error code function possible cause(s) e5- 05 vp (+24v, scanner) 1. Sdr p...
Page 156
156 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 note: these error codes will appear only when the optional accessories are installed. Refer to the appropriate optional unit service manual. Technician warning: the following message will be displayed in the event that the required additional sort memor...
Page 157
157 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 4.7. Information codes table (for facsimile) fax information codes code mode phase description of problem possible cause(s) 012 rcv c, d the length of the received document is over 2 m. 030 xmt b read point sensor does not activate within 4 seconds aft...
Page 158
158 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 405 xmt b transmitter received ftt after it transmitted tcf at 2400 bps. Received rtn after communicating at 2400 bps. Line quality poor. (tcf is damaged due to line noise) receiver defective. (modem, mjr pcb, etc.) fxb pcb or mjr pcb defective. 406 rcv...
Page 159
159 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 418 rcv c receiver transmitted pin in response to pri-q from transmitter. (transmitting operator requests voice contact) line quality poor. (there are excessive errors in received data) fxb pcb or mjr pcb defective. 420 rcv b t1 timer (35 sec.) elapsed...
Page 160
160 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 503 xmt/ rcv(v.34) b, c, d cs of modem is not able to turn on during training. Fxb pcb defective. Line disconnected. 504 rcv/v.34 (polling) b polling is rejected from the remote station. No polling original set. 505 xmt/v.34 (polling) b polling xmt is r...
Page 161
161 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 634 xmt pstn redial count over with no response or busy tone was not detected. Note: u.S.A. And canadian models will redial only once if a busy tone is not detected. 638 xmt pstn lan power turned off with applicable data in memory or during communicati...
Page 162
162 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 727 xmt lan received an error or no response from the remote internet fax. (smtp direct xmt) remote internet fax errors: busy or job number overflow for relay xmt. (retry is possible) 728 xmt lan remote internet fax errors: memory overflow or no power. ...
Page 163
163 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 4.8. Diagnostic codes (for facsimile) the 13-digit diagnostic code is provided for the service engineer to analyze how the communication was performed. The code is recorded on the journal. Journal example 1st digit: manufacturer code -: not used/define...
Page 164
164 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 2nd digit -: not used/defined 3rd digit -: not used/defined fax diagnostic codes data definition id (tsi, csi, cig) rtn dcn stop button 0 - - - - 1 received - - - 2 - received - - 3 received received - - 4 - - received - 5 received - received - 6 - rece...
Page 165
165 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 4th digit -: not used/defined 5th digit -: not used/defined fax diagnostic codes data definition scanning rate resolution 0 20 ms/line std 1 5 ms/line std 2 10 ms/line std 3 - std 4 40 ms/line std 5 - std 6 - std 7 0 ms/line std 8 20 ms/line fine 9 5 m...
Page 166
166 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 6th digit -: not used/defined 7th digit -: not used/defined fax diagnostic codes data definition polling xmt/rcv selective comm. Password comm. 0 - rcv off off 1 yes rcv off off 2 - xmt off off 3 yes xmt off off 4 - rcv on off 5 yes rcv on off 6 - xmt o...
Page 167
167 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8th digit -: not used/defined 9th digit -: not used/defined fax diagnostic codes data definition advanced comm. Cover sheet xmt 0 - - 1 report xmt - 2 check & call - 3 - - 4 memory transfer - 5 - - 6 - - 7 - - 8 - yes 9 report xmt yes a check & call ye...
Page 168
168 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 10th digit -: not used/defined 11th digit -: not used/defined fax diagnostic codes data definition coding ecm 0 mh - 1 mr - 2 mmr - 3 jbig - 4 - - 5 - - 6 - - 7 - - 8 mh yes 9 mr yes a mmr yes b jbig yes c - yes d - yes e - yes f - yes fax diagnostic co...
Page 169
169 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 12th digit -: not used/defined 13th digit -: not used/defined fax diagnostic codes data definition modem speed modem speed (v.34) 0 2400 bps - 1 4800 bps 2400 bps 2 7200 bps 4800 bps 3 9600 bps 7200 bps 4 tc 7200 bps 9600 bps 5 tc 9600 bps 12000 bps 6 ...
Page 170
170 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 4.9. Troubleshooting (for printer) 4.9.1. Checking the basics 4.9.2. Document does not print properly this section explains how to solve problems including error messages or unexpected printing results. If the printing system is not printing or working ...
Page 171
171 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 4.9.3. Error message appears on the pc 4.9.4. Error message appears on the unit 4.9.5. System error (cd drive related error during installation) error message possible solution(s) network print dll error. • check if the panasonic device is turned "on" ...
Page 172: 5 Service Modes
172 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 5 service modes 5.1. Service modes (for copier) these service modes are provided to assist the technician in checking for abnormalities in the copier and a means of making adjustments to the input/output of major components. Caution: the factory default...
Page 173
173 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 f5 / f6 information list (sample) * * * * * * * * * * - f 5 / f 6 i n f o r m a t i o n l i s t - * * * * * * d a t e m m m - d d - y y y y * * * t i m e 1 2 : 0 1 * * * p . 0 1 f5-00 country version usa/can f5-50 auto contrast adjust. Yes f5-01 freque...
Page 174
174 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 2.Firmware version sc : aav0000xpu 1.Machine information machine name : dp-3030 mac address : 08002312137e sc boot : m13 pnl : aav0000xpu spc : 30cpm v0000x finisher : ver 6d01 fax modem : pdl font1 : sc2 : 3.Memory capacity page memory : 32 mb sort mem...
Page 175
175 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 f7 total counter list (sample) f7-01 key operator id code : 0000 f7-02 maintenance count total count : 295 pm count : 295 scanner pm count : 61 adf count : 26 opc drum count : 295 process unit count : 295 adf pm count : 50 fuser web count : 295 develop...
Page 176
176 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 5.1.3. F4 mode: input/output status test set the machine to service mode and press "4" key on the keypad. ↓ press the "start" key. ↓ enter the number to activate the test then press "start" key. ↓ press "stop" key to cancel the test. ↓ when the "c (clea...
Page 177
177 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 004 fuser unit paper exit sensor paper is detected. 0 dual-path exit guide unit detection sensor unit is connected. 0 adu detection sensor unit is connected. 0 jam access cover open detection sensor (2nd paper feed module) cover is open. 0 upper limit ...
Page 178
178 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 007 paper transport unit detection sensor unit is connected. 0 paper transport unit door sensor door is open. 0 paper transport unit sensor 4 paper is detected. 0 paper transport unit sensor 3 paper is detected. 0 paper transport unit sensor 2 paper is ...
Page 179
179 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 010 registration sensor (3rd paper tray) paper is detected. 0 jam access cover open detection sensor (3rd paper tray) cover is open. 0 paper tray detection sensor (3rd paper tray) paper tray is connected. 1 upper limit sensor (3rd paper tray) upper lim...
Page 180
180 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 020 size sensor c original detected on the c position. 1 size sensor b original detected on the b position. 1 size sensor a original detected on the a position. 1 size sensor z original detected on the z position. 1 size sensor y original detected on th...
Page 181
181 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 031 adf original sensor original is detected. 1 adf original width sensor original is detected. 1 adf original width sensor original is detected. 1 adf original length sensor 2 original is detected. 1 adf original length sensor 1 original is detected. ...
Page 182
182 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 2. Output check press the "start" key to start and press the "stop" key to reset. F4 mode (output check) no. Item function remark 040 total counter when spc pcb cn715-8 signal level changes to 0v from +24v, count up the total counter. 041 key counter / ...
Page 183
183 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 064 lift motor (1st paper tray) when spc pcb cn706-2 signal level changes to 0v from +24v, motor rotates in the ascending direction. 065 opc clutch when spc pcb cn728-2 signal level changes to 0v from +24v, clutch operates. 1 minute 066- 069 not used 0...
Page 184
184 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 087 adu intermediate roller clutch when spc pcb cn711-2 signal level changes to 0v from +24v, the clutch operates. 088- 099 not used 100 inner upper paper exit solenoid when spc pcb cn719-3 signal level changes to 0v from +24v, the clutch turns off. 101...
Page 185
185 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 163 adf paper feed motor reverse rotating (35% speed rotating) adf paper feed motor rotates in reverse at 35% speed. 164 adf paper feed motor reverse rotating (100% speed rotating) adf paper feed motor rotates in reverse at 100% speed. 165 adf paper fe...
Page 186
186 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 5.1.4. F5 mode: function parameters (for copier) set the machine to service mode and press "5" key on the keypad. ↓ press the "start" key. ↓ select the desired code number on the touch panel display. ↓ if you wish to select another code number, scroll t...
Page 187
187 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 07 language default english french german swedish italian dutch portugal spanish norway danish finnish english polish hungary japanese czech russian greek chinese taiwan korean english 08 batch printing mode (from april 2004 mp) 0 : off 1 : on 1 09 fus...
Page 188
188 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 18- 19 not used 20 adf 0 : no 1 : auto 1 21 finisher 0 : no 1 : auto 1 22 system console 0 : no 1 : auto 1 23 paper transport unit 0 : no 1 : auto 1 24 not used 25 digital quantum 0 : off 1 : on 1 26 2-sided unit 0 : no 1 : auto 1 27- 29 not used 30 dua...
Page 189
189 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 44 insert paper count 0 : no 1 : yes 0 45 dept code reentry again 0 : no 1 : yes 1 46- 47 not used 48 th sensor (dev) 0 : no 1 : mid 2 : large 1 49 not used 50 auto contrast adjust 0 : no 1 : yes 1 51 dept. Counter (copy) 0 : no 1 : yes 1 52 dept. Coun...
Page 190
190 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 67 page insertion default 0 : blank 1 : copy 0 68 cover mode default 0 : f, blank 1 : f, copy 2 : fb, blank 3 : fb, copy 0 69 reduce n in 1 space 0 : no 1 : yes 0 70 pm cycle 0 : no 1 : 1.5 k 2 : 2.5 k 3 : 5 k 4 : 10 k 5 : 15 k 6 : 20 k 7 : 30 k 8 : 40 ...
Page 191
191 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 81 b4/fls size selection 0 : b4 1 : 8 x 13 2 : 8.5 x 13 0 82 manual skyshot mode 0 : off 1 : m1, on 2 : m2, on 3 : m1, m2, on 0 83 digital skyshot mode 0 : no 1 : normal 2 : quality 1 84 paper tray priority 0 : s > c > b 1 : c > s > b 1 85 side void se...
Page 192
192 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 96 bypass detection (factory use only) 0 : japan 1 : usa/can 2 : europe 3 : other 1 (for usa / canada) 2 (for europe) 97 bp tray b4/fls/lgl (fa) (factory use only) 0 : b4 1 : 8 x 13 2 : 8.5 x 13 3 : legal 3 (for usa / canada) 0 (for europe) f5 mode no. ...
Page 193
193 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 5.1.5. F6 mode: adjust parameters (for copier) set the machine to service mode and press "6" key on the keypad. ↓ press the "start" key. ↓ select the desired code number on the touch panel display. ↓ if you wish to select another code number, scroll th...
Page 194
194 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 15 not used 16 side adjust (adu) adjustment of lsu side-side (adu). -8 - +7 0.5mm 17 charge roller voltage charge voltage compensation adjustment. -76 - +76 2.60v 18 standard laser power laser power compensation adjustment. -29 - +25 19 std bias dc volt...
Page 195
195 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 47 transfer current side 2 adjustment of transfer current. -16 - +15 0.6ua 48 not used 49 t mode image density image density adjustment for text mode. (-) : darker. (+) : lighter. -99 - +99 50 t/p mode image density image density adjustment for text/ p...
Page 196
196 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 81 quantum halftone read value of quantum laser duty of check pattern. +127 - +255 (read only) 82 quantum black read value of quantum laser duty of black pattern. +127 - +255 (read only) 83 temperature sensor value value of temperature sensor. 0 - 255 (...
Page 197
197 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 5.1.6. F7 mode: electronic counter set the machine to service mode and press "7" key on the keypad. ↓ press the "start" key. ↓ select the desired code number on the touch panel display. ↓ if you wish to select another code number, scroll the menu with ...
Page 198
198 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 f7 electronic counters 03 paper feed count 00 sheet bypass count total count of paper fed from the sheet bypass. 01 1st paper tray count total count of paper fed from the 1st paper tray. 02 2nd paper tray count total count of paper fed from the 2nd pape...
Page 199
199 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 5.1.7. F8 mode: service adjustment set the machine to service mode and press "8" key on the keypad. ↓ press the "start" key. ↓ select the desired code number on the touch panel display. ↓ if you wish to select another code number, scroll the menu with ...
Page 200
200 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 19 move mirror to lock a) press the start key to move the mirror unit to the locked position for transporting the copier. B) when the mirror unit is locked, the machine will not accept any numerical key input. Note: the locking operation is automaticall...
Page 201
201 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 5.1.8. F9 mode: unit maintenance set the machine to service mode and press "9" key on the keypad. ↓ press the "start" key. ↓ select the desired code number on the touch panel display. ↓ if you wish to select another code number, scroll the menu with th...
Page 202
202 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 f9 unit maintenance 06 ram initialize 00 parameter initialize resets the fax and function parameters to default values. Note: turn the power switch to the off and back to the on position to enable the parameter settings. 01 all job clear clears all jobs...
Page 203
203 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 5.2. Service modes (for facsimile) caution: the factory default parameters are preset (country dependent) for optimum performance and in compliance with the local telecommunication regulations/standards, and do not need to be changed. Changing some of ...
Page 204
204 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 5.2.3. Fax service mode 1 (function parameter setting) use the following procedure to change the function parameters. Select the "01 function param. Setting" on the touch panel display. ↓ select the desired code number on the touch panel display. ↓ if y...
Page 205
205 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 005 destination code 000 : austria 001 : u.K. 002 : canada 003 : denmark 004 : taiwan 005 : finland 006 : germany 007 : netherlands 008 : italy 009 : spanish 010 : hong kong 011 : australia 012 : switzerland 013 : norway 015 : portuguese 016 : ireland ...
Page 206
206 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 012 dtmf level 00 = 0 dbm ~ 15 = -15 dbm selects the dtmf output level, 0 to -15 dbm in 1 dbm steps. 013 g3 rx eql 1 = 0db 2 = 4db 3 = 8db 4 = 12db selects the cable equalizer for g3 reception mode, 0db, 4db, 8db or 12db. 014 g3 tx eql 1 = 0db 2 = 4db 3...
Page 207
207 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 026 non-standard 1 = off (invalid) 2 = on (valid) selects own mode (panafax mode). 027 short protocol b 1 = off (invalid) 2 = on (valid) selects the short protocol mode. 028 short protocol d 1 = off (invalid) 2 = on (valid) selects the short protocol m...
Page 208
208 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 046 on-hook time 0 = 0 sec. ~ 90 = 90 sec. Selects the on-hook time between sequential communication calls in 1 second step intervals. 047 response wait interval 1 = 1 sec. ~ 90 = 90 sec. 20 ~ 150 sec. (for france only) selects the waiting interval for ...
Page 209
209 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 068 nyse fax forward (usa and canada only) 1 = off 2 = on selects whether the machine will forward the incoming and outgoing faxes to a specified station. Note: once this parameter is activated, fax forwarding via fax parameter 054 is automatically dis...
Page 210
210 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 083 not used 084 line as no paper 1 = ring (ring) 2 = busy (keep line busy) selects whether to ring or send a busy tone to the remote station when the recording paper runs out or the unit cannot receive because of any trouble. 085 not used 086 reduction...
Page 211
211 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 note 1: continuous polling (station mode) this feature allows you to store or add documents into a polled file in memory. To enable the continuous polling feature set function parameter no. 003 to "2:station". The last program key will be assigned with...
Page 212
212 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 5.2.4. Fax service mode 3 (printout of lists, reports and test results) from this service mode you can print the function parameter list, page memory test, printer report, all document file, protocol trace and the toner order form. 5.2.4.1. Function par...
Page 213
213 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 function parameter list (sample) ************* -function parameter- ************* date mmm-dd-yyyy ***** time 12:07 ***p.01 -panasonic - ***** dp-3030 ******************* - - ****** -12345678901234567890- ********* 000 monitor/tel dial monitor 050 ring...
Page 214
214 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 note: 1. The contents of the function parameter list may vary depending on the country’s regulations. 2. “ * ” mark will be shown on the left side of number when setting was changed from default. Function parameter list (sample) ************* -function ...
Page 215
215 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 5.2.4.2. Page memory test a test pattern prints out for checking the page memory (ic120 and ic121 on the sc pcb) and printer mechanism using the following procedure. Select the "03 print param. List/report" on the touch panel display. ↓ select the "03 ...
Page 216
216 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 5.2.4.3. Printer report all printer errors are logged on the printer report which can be printed by the following procedure. Select the "03 print param. List/report" on the touch panel display. ↓ select the "04 printer report" on the touch panel display...
Page 217
217 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 5.2.4.4. All document files print the document files from the flash memory. Select the "03 print param. List/report" on the touch panel display. ↓ select the "05 all document files" on the touch panel display. ↓ touch the "ok" button 3 times. ↓ press "...
Page 218
218 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 5.2.4.5. Protocol trace print a protocol trace report for the previous communication. Select the "03 print param. List/report" on the touch panel display. ↓ select the "06 protocol trace" on the touch panel display. ↓ touch the "ok" button 3 times. ↓ pr...
Page 219
219 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 5.2.4.6. Toner order form the toner order form can be printed out manually by the following procedure. Select the "03 print param. List/report" on the touch panel display. ↓ select the "07 toner order form" on the touch panel display. ↓ touch the "ok" ...
Page 220
220 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 explanation of contents (1) low toner message (fixed) “the toner supply in your machine is running low” (2) dealer name up to 25 digits (3) toner order tel # up to 36 digits (4) toner order fax # up to 36 digits (5) customer id up to 16 characters (user...
Page 221
221 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 5.2.5. Fax service mode 4 (modem test) 5.2.5.1. Binary signal this service mode is used to check the binary signal output. Signals can be output to the line using the following procedure. Select the "04 modem tests" on the touch panel display. ↓ select...
Page 222
222 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 5.2.5.2. Tonal signal this service mode is used to check the tonal signal output. Signals can be output to the line using the following procedure. Select the "04 modem tests" on the touch panel display. ↓ select the "02 tonal signal" on the touch panel ...
Page 223
223 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 5.2.5.3. Dtmf signal this service mode is used to check the dtmf (dual tone multi frequency) signal output. The dtmf signal can be generated using the following procedure. • dtmf single tone select the "04 modem tests" on the touch panel display. ↓ sel...
Page 224
224 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 5.2.5.4. Binary signal (v.34) this service mode is used to check the binary signal output. Signals can be output to the line using the following procedure. (v.34) select the "04 modem tests" on the touch panel display. ↓ select the "05 v34 modem" on the...
Page 225
225 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 5.2.6. Fax service mode 6 (ram initialization) initializes ram and restores the function parameters to their default values. Note: this operation should be performed when the unit is first installed. Select the "06 ram initialize" on the touch panel di...
Page 226
226 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 5.2.7. Fax service mode 8 (check & call) 5.2.7.1. Overview this feature enables the authorized servicing dealers to manage and improve the machine maintenance to their customers by alerting them of equipment problems. It also can be used as a supply sal...
Page 227
227 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 note: tx (transmission) report: s = service alert report, m = maintenance alert report error code log tx report remarks ex-xx o s refer to the mechanical error code (e code) table. (sect. 4.6.3.) e13 o out of toner. Jxx o refer to the jam error code (j...
Page 228
228 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 5.2.7.3. Service alert report format explanation of contents (1) customer id (2) firmware version (3) counter information (4) print error last 30 records (latest on top) (5) serial number dp-2330/3030 only ***********************************************...
Page 229
229 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 5.2.7.4. Maintenance alert report format explanation of contents (1) low toner message (fixed) “machine is running out of toner” (2) customer id up to 16 characters (user identification code) (3) firmware version (4) transmission / reception / copy / p...
Page 230
230 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 5.2.7.5. Toner order form explanation of contents (1) low toner message (fixed) “the toner supply in your machine is running low” (2) dealer name up to 25 digits (3) toner order tel # up to 36 digits (4) toner order fax # up to 36 digits (5) customer id...
Page 231
231 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 5.2.7.6. Call counter report explanation of contents (1) customer id (2) firmware version (3) counter information (4) call counter pre-set value (5) serial number dp-2330/3030 only *************************************************** date mmm-dd-yyyy **...
Page 232
232 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 5.2.8. Service mode 9 (system maintenance) 5.2.8.1. Overview this service mode is used to maintain the machine. Use the following procedure for system maintenance. Select the "09 system maintenance" on the touch panel display. ↓ select the "01 send rcv’...
Page 233: 6 System Description
233 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 6 system description 6.1. Printing process exit paper feed toner discharge lamp: transfer / separation fusing: cleaning: primary charge: image exposure: developing: drum surface approximately-750v dc charge roller drum latent charge image illumination ...
Page 234
234 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 6.2. Precaution with consumables (1) photoreceptor (opc) drum - be careful not to smear the surface with saliva, water, oil, etc. - do not store in places where the temperature is high. - do not store it in strong light (such as direct sunlight or on th...
Page 235
235 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 5) safety and hygiene due to its properties, toner can be easily wind blown. Toner on skin does not cause any health risk. However inhalation is undesirable even if the powder is simply dust. Therefore, be careful not to inhale toner. - handle the tone...
Page 236
236 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 6.3. New image stabilizing technology to improve the copy quality, a new toner density controller (quantum ii system) is developed. The most important aim was to stabilize the toner density under various office environments. Up to now, the control metho...
Page 237
237 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 3. Control method 4. Quantum adjustment print density data print density data image density image density ideal curve high density (black patch) low density (check patch) control point 255 0 255 0 table1 table2 table3 table4 table5 text, t/p mode contr...
Page 238
238 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 5. Installing / replacing developer 6. Installing / replacing opc drum & sensor replacement 7. Service parameters for copy image compensation after f8-09 => f6-21: tdc gain voltage (0.1% / step) f6-26: tdc judgement level + tdc adjustment quantum contro...
Page 239
239 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 6.4. Mechanical operation 6.4.1. Scanning mechanism (flatbed) 1. Scanning mechanism the scanning mechanism consisting of lens, ccd pcb assy (207), mirrors, xenon lamp (204), lamp base bracket (224) and mirror 2 bracket (233), is used to scan originals....
Page 240
240 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 detection sensor (270) stepping motor (201) when scanning originals when returning to standby position drive shaft (256) lamp base bracket (224) rear mirror clamp (235) rear lamp belt lock (226) mirror 2 bracket (233).
Page 241
241 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 6.5. Automatic document feeder the adf (automatic document feeder) automatically feeds paper into the unit, one original at a time. Its main features are: 1. Place originals face-up 2. Correct order stacking (collation mode) 3. Paper feed mechanism wit...
Page 242
242 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 4. Transmission and ejection the original is fed into the drive roller (3205) and when the original actuates the read point sensor (1045), the adf roller stops rotating. The eject sensor (1045) detects the scanning position and the feed 2 roller (1753) ...
Page 243
243 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 2. Scanning the front and the back side of an original the scanning of the front and back side of a 2-sided original is accomplished by means of the duplex 2 guide (1857) and inverting 1 guide (1858). After the front side of the original is scanned, th...
Page 244
244 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 6.6. Receive mechanism 6.6.1. Paper feed modules 1. Paper feed module (1st/2nd/3rd/4th) a. The np actuators (1133) attached to the paper feed blocks no.1, 2, 3 and 4 determine if there is paper in the paper tray. B. The paper in the paper tray lifts up ...
Page 245
245 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 a. When the printing operation begins, the main motor (907) starts driving the gears. B. The clutch (1105) is energized for a specified period of time and turns on. This activates the paper feed roller (1144). The paper is separated into individual she...
Page 246
246 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 a. When the printing operation begins, the main motor (907) and the drive motor (2402) start driving the gears. B. The clutch (1105) is energized for a specified period of time and turns on. This activates the paper feed roller (1144). The paper is sepa...
Page 247
247 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 a. When inserting the paper tray into the machine, the np sensor (1045) activates. At the same time, the lift plate (2009) is combined with the coupling which drives the lift plate of the machine. The lift plate rotates, lifting the bottom plate (2008)...
Page 248
248 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 a. The recording paper size in the paper feed module is set on the touch panel. Lift dc motor (1152) coupling (1171) np sensor (1045).
Page 249
249 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 2. Sheet bypass (for dp-2310/3010) a. The np actuator attached to the paper feed unit determines if there is paper in the paper tray. B. The paper in the paper tray lowers the np actuator and the np sensor (1045) actuates. A. When the printing operatio...
Page 250
250 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 3. Sheet bypass (for dp-2330 / 3030) a. The np actuator attached to the paper feed unit determines if there is paper in the paper tray. B. The paper in the paper tray lowers the np actuator and the np sensor (1045) actuates. A. When the printing operati...
Page 251
251 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 6.6.2. Laser unit 1. Laser this laser uses the semiconductor laser. The beam power on the drum surface is approximately 0.4 mw. 2. Collimator lens and cylindrical lens these lenses converge and focus the laser beam, converting it to parallel light. 3. ...
Page 252
252 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 6.6.3. Fuser operation the paper passes through the fuser roller (1026) and is subjected to heat and pressure in the fuser unit. Pressure between the fuser roller (1026) and pressure roller (1027) fuses or bonds the toner into the paper. Fuser roller (1...
Page 253
253 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 cleaning web roller (1083) the cleaning web roller (1083) is installed in the fuser unit, which keeps cleaning the surface of the fuser roller (1026). When the fuser unit does not reach the specified temperature within a certain period of time, an erro...
Page 254
254 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 6.7. Glossary of electrical abbreviations signal name function +12v +12 vdc power supply +24v +24 vdc power supply +24vd1 +24 vdc power supply +24vd2 +24 vdc power supply +24vhl +24 vdc power supply +24vfb +24 vdc power supply +24vfl +20/+24 vdc power s...
Page 255
255 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 gaclk- gate array clock - gnd ground gopsw1 developer missing detection hsync horizontal synchronous signal humsn temp humidity sensor signal iicscl iic transmission clock iicsda iic transmission signal iouta motor control signal ioutb motor control si...
Page 256
256 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 ldphk4 photo sensor dc drive voltage ldps photo sensor dc drive voltage ldrsen photo sensor dc drive voltage ldtf photo sensor dc drive voltage ldupl photo sensor dc drive voltage ldupl2 photo sensor dc drive voltage ldupl3 photo sensor dc drive voltage...
Page 257
257 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 ncclh2 adf roller clutch control signal ncclh3 inverting roller clutch control signal nclpin afe sample hold clamp signal ncount counter drive signal ncst2 2nd paper tray detection signal ncst3 3rd paper tray detection signal ncst4 4th paper tray detec...
Page 258
258 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 nlpow2 not used nmfpck sheet bypass paper detection signal nmfrchk sheet bypass pressure plate detection signal nmfsen4 sheet bypass paper length detection signal nmmck main motor clock nmmon main motor rotation control signal nmmp0a motor drive signal ...
Page 259
259 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 ntrpsen1 transport unit sensor signal ntrpsen2 transport unit sensor signal ntrpsen3 transport unit sensor signal ntrpsen4 transport unit sensor signal nvrdy vsync reset signal nvreq print ack request signal nwake fax wake up signal opccnt opc drum clu...
Page 260
260 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 spcrxd spc reception data signal spctxd spc transmission data signal spow scanner 24v control signal strvp control signal tdref toner density reference sensor tdsn toner density sensor signal ted toner detect sensor signal tempsn temp humidity sensor si...
Page 261: 7 Installation
261 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 7 installation 7.1. Precautions during set up before you begin the installation, read these entire instructions. You must locate an appropriate site (firm and leveled surface) for the installation. Reading this section assists you with the decision mak...
Page 262
262 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 space requirements for copier and options 27.83 in (707 mm) 27.83 in (707 mm) 27.83 in (707 mm) 14.2 in (379 mm) 14.92 in (379 mm) 14.92 in (379 mm) copier + finisher copier + outer exit tray copier 3.94 in (100 mm) 3.94 in (100 mm) 10.83 in (275 mm) 14...
Page 263
263 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 7.2. Unpacking visually check the condition and contents of the box for completeness or any shipping damage before installation. Remove all filament tapes used to secure the fuser and process units during shipment. Caution: the machine weights approxim...
Page 264
264 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (2) open the left rear handle cover and swing the handle downwards to lock it in place. Note: to release the handle, push the release latch toward the machine, pull out then lift up the handle into the machine. (3) open the right front handle cover and ...
Page 265
265 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (4) open the right rear handle cover, lift up and pull out the handle to lock it in place. Note: to release the handle, push the release latch toward the machine, push down the handle into the machine. (5) lift and place the machine on a suitable stand...
Page 266
266 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (9) remove the tape. (10) remove 1 blue screw. (11) remove the shipping metal bracket by rotating counterclockwise to unlock the scanner. (12) reinstall the left platen cover. (13) store the shipping metal bracket and the blue screw into the space provi...
Page 267
267 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (19) remove 1 screw. (20) remove the front fixing metal bracket (longer plastic tab). (21) remove 1 screw. (22) remove the rear fixing metal bracket (shorter plastic tab). (23) carefully remove the packing tape and protective sheet from the opc drum as...
Page 268
268 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (31) remove the tape and the instruction paper. Note: before installing the process unit into the machine, ensure that the shutter's alignment guide is positioned as illustrated. (32) open the front cover wide. (33) remove 1 screw. (34) remove the conne...
Page 269
269 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (35) install the process unit. Caution: to prevent damage to the process unit, ensure the right cover is still open before inserting the process unit into the machine. Caution: exercise caution not to scratch the surface of the opc drum (green), and no...
Page 270
270 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 7.3.2. Toner density control (tdc) adjustment 1. Press the "function", "original size (ledger/a3)" and "3" keys simultaneously in that order to enter the service mode. 2. Press the "8" key to enter the f8 mode (service adjustment). 3. Press the "start" ...
Page 271
271 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 7.3.4. Set the date and time 1. Press the "function" key. 2. Touch the "general settings" button. 3. Select the "09 key operator mode". 4. "input identification code" (default is 0000). 5. Touch the "ok" button. 6. Touch the button to advance to: (dp-2...
Page 272
272 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 12. Enter f2 mode (single copy test). 13. Make a copy to confirm the adjustment. Note: repeat step (3) to (10) until proper density is attained. F6-49 : t mode image density (text) f6-51 : p mode image density (photo) 14. Press “function” and “c” (clear...
Page 273: 8 Options and Supplies
273 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8 options and supplies 8.1. Service notes "firmware update" for pcl-ipx/spx or ps-ipx/spx option installation (for dp-2330/3030) to use pcl-ipx/spx (da-pc301) or ps-ipx/spx (da-mc301) option individually or in combination with other options, changing t...
Page 274
274 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 main unit firmware code updating instructions 1. Updating through a lan port (the quickest and most easiest method) the firmware code can be easily updated when the main unit is connected to a lan. The network firmware update tool can also be used by co...
Page 275
275 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 note: 1. Manual mode must be used, when updating the designated version of the firmware or changing the type of the firmware. Please refer to the section 2.2, "setting up the network firmware update tool, file selection tab" of the operating instructio...
Page 276
276 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 to: firmware data folder: c:\ panasonic \ panasonic-fup \ data 3) preparing the main unit for the firmware upgrade important: do not connect the usb cable yet. Print the f5/f6 parameters list (copier service mode f9-03-00). Enter into test mode f9-07-01...
Page 277
277 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8.2. Service notes "firmware update" for pcl or ps option installation (for dp-2310/3010) to use pcl (da-pc300) or ps (da-mc300) option individually or in combination with other options, changing to type b or type d sc firmware is required. The require...
Page 278
278 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 main unit firmware code updating instructions 1. Updating through a lan port (the quickest and most easiest method) the firmware code can be easily updated when the main unit is connected to a lan. The network firmware update tool can also be used by co...
Page 279
279 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 note: 1. Manual mode must be used, when updating the designated version of the firmware or changing the type of the firmware. Please refer to the section 2.2, "setting up the network firmware update tool, file selection tab" of the operating instructio...
Page 280
280 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 to: firmware data folder: c:\ panasonic \ panasonic-fup \ data 3) preparing the main unit for the firmware upgrade important: do not connect the usb cable yet. Print the f5/f6 parameters list (copier service mode f9-03-00). Enter into test mode f9-07-01...
Page 281
281 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8.3. Installing the printer controller module for gdi-ipx/spx (da-gc601) 8.3.1. Contents note: 1.The part number may differ depending on the destination. 2. Refer to the parts list in the parts manual. 8.3.2. Installation caution! Turn the power switch...
Page 282
282 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (3) install the hardware key into one of the three available connectors (cn67, cn68 or cn69) on the sc pc board. Note: the connectors are keyed, to prevent damage to the sc pc board, install the hardware key as illustrated. Do not force the hardware key...
Page 283
283 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8.4. Installing the printer controller module for pcl6 (da-pc300) 8.4.1. Contents note: 1.The part number may differ depending on the destination. 2. Refer to the parts list in the parts manual. 8.4.2. Installation 1. Before installing this option, mak...
Page 284
284 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (3) install the hardware key into one of the three available connectors (cn67, cn68 or cn69) on the sc pc board. Note: the connectors are keyed, to prevent damage to the sc pc board, install the hardware key as illustrated. Do not force the hardware key...
Page 285
285 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8.5. Installing the printer controller module for pcl6-ipx/spx (da-pc301) 8.5.1. Contents note: 1.The part number may differ depending on the destination. 2. Refer to the parts list in the parts manual. 8.5.2. Installation 1. Before installing this opt...
Page 286
286 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 note: 1. This option can also be used for dp-2310/3010 without ipx/spx. 2. The firmware included on the cd-rom with this option is intended for dp-2330/3030, it cannot be used for dp-2310/3010. Please use the dp-2310/3010 firmware provided separately by...
Page 287
287 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8.6. Installing the printer controller module for ps / pcl6 (da-mc300) 8.6.1. Contents note: 1.The part number may differ depending on the destination. 2. Refer to the parts list in the parts manual. 8.6.2. Installation 1. Before installing this option...
Page 288
288 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (3) install the hardware key into one of the three available connectors (cn67, cn68 or cn69) on the sc pc board. Note: the connectors are keyed, to prevent damage to the sc pc board, install the hardware key as illustrated. Do not force the hardware key...
Page 289
289 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8.7. Installing the printer controller module for ps / pcl6-ipx/spx (da-mc301) 8.7.1. Contents note: 1.The part number may differ depending on the destination. 2. Refer to the parts list in the parts manual. 8.7.2. Installation 1. Before installing thi...
Page 290
290 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 note: 1. This option can also be used for dp-2310/3010 without ipx/spx. 2. The firmware included on the cd-rom with this option is intended for dp-2330/3030, it cannot be used for dp-2310/3010. Please use the dp-2310/3010 firmware provided separately by...
Page 291
291 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8.8. Installing the network scanner module (da-ns600) 8.8.1. Contents note: 1.The part number may differ depending on the destination. 2. Refer to the parts list in the parts manual. 8.8.2. Installation caution! Turn the power switch on the left side a...
Page 292
292 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (3) install the hardware key into one of the three available connectors (cn67, cn68 or cn69) on the sc pc board. Note: the connectors are keyed, to prevent damage to the sc pc board, install the hardware key as illustrated. Do not force the hardware key...
Page 293
293 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8.9. Installing the network scanner module for dds (da-ns601) 8.9.1. Contents note: 1. This option is intended to be used with the document distribution system (da-wr10) for dp-2330/3030. 2. The part number may differ depending on the destination. 3. R...
Page 294
294 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 note: 1. The network scanner (da-ns600) cannot be installed together with this option. If the network scanner (da-ns600) is already installed, remove it first. (3) install the hardware key into one of the three available connectors (cn67, cn68 or cn69) ...
Page 295
295 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8.10. Installing the internet fax / e-mail module (da-nf600) 8.10.1. Contents note: 1.The part number may differ depending on the destination. 2. Refer to the parts list in the parts manual. 8.10.2. Installation caution! Turn the power switch on the le...
Page 296
296 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (3) install the hardware key into one of the three available connectors (cn67, cn68 or cn69) on the sc pc board. Note: the connectors are keyed, to prevent damage to the sc pc board, install the hardware key as illustrated. Do not force the hardware key...
Page 297
297 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 perform the following steps if the optional hard disk drive unit (da-hd30) is also installed. An additional 800 stations (1,000 total) are available when the optional hard disk drive (da-hd30) is installed. If you wish to use the 1,000 fax address book...
Page 298
298 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 using the network address book editor to copy and paste the address book data 1. An appropriate address book editor module is automatically selected depending on which style of fax address book is activated on the dp-23xx/30xx. Retrieve the 200 station,...
Page 299
299 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8.11. Installing the fax communication board (da-fg300) 8.11.1. Contents note: 1. If also installing the program expansion board (da-em600), it must be installed first. 2. The part number may differ depending on the destination. 3. Refer to the parts l...
Page 300
300 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 caution: if the red leds on the sc and spc pc boards are on, the power is still on. Please read these installation instructions once again. (3) release the pre-installed 2 wire harness from 2 harness clamps. (4) plug the fxb pc board assembly into the s...
Page 301
301 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (9) remove the lower protective tab on the left rear cover for the line connection. If installing an external telephone, remove the upper protective tab as well. (10) attach the line label to the left rear cover as illustrated. (11) install the mjr pc ...
Page 302
302 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (18) disconnect the harness. (19) loosen 1 screw. (20) slide the process unit out. Caution: to prevent damage to the process unit, ensure the right cover is still open before pulling the process unit out. Caution: exercise caution not to scratch the sur...
Page 303
303 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (30) attach the type approval label (specified destination) to the lower rear cover as illustrated. (31) proceed with the installation of other options. If finished, close and secure the rear cover and reinstall remaining covers. (32) connect one end o...
Page 304
304 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (34) it is not necessary to set the parameter for the following suffix (destinations). The fax firmware is automatically loaded with the host firmware. Pb : uk pf : france pg : switzerland pk : china pm: germany pt : taiwan pu : usa note: for other dest...
Page 305
305 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (35) execute parameter initialize by following the steps below. A) press the "function", "original size (ledger/a3)" and "3" keys simultaneously in that order to enter the service mode. B) press the "9" and "start" keys to enter the f9 mode (unit maint...
Page 306
306 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 8.11.3. Perform the following steps if the optional hard disk drive unit (da-hd30) is also installed an additional 800 stations (1,000 total) are available when the optional hard disk drive (da-hd30) is installed. If you wish to use the 1,000 fax addres...
Page 307
307 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 using the network address book editor to copy and paste the address book data 1. An appropriate address book editor module is automatically selected depending on which style of fax address book is activated on the dp-23xx/30xx. Retrieve the 200 station...
Page 308
308 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 8.12. Installing the hard disk drive unit (da-hd30) 8.12.1. Contents note: 1.The part number may differ depending on the destination. 2. Refer to the parts list in the parts manual. 8.12.2. Installation 1. Before installing the hard disk drive unit, mak...
Page 309
309 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 caution: if the red leds on the sc and spc pc boards are on, the power is still on. Please read these installation instructions once again. (3) install the dc pc board onto the rear cover as illustrated. (4) secure the dc pc board with 2 screws. (5) in...
Page 310
310 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (13) remove 2 screws. (14) open the lvps cover. (15) connect the dc12 harness to cn145 on the dc pc board. (16) secure the dc12 harness with the 2 harness clamps. (17) install the hdd into the hdd bracket. (18) secure the hdd bracket with 4 silver screw...
Page 311
311 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (22) install 1 harness clamp (medium). (23) connect one end of the hd harness to the hdd. (24) secure the hd harness with the harness clamp. Note: make sure that the hd harness is connected to the hdd correctly as illustrated. 1) the key on the connect...
Page 312
312 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 caution! After the hard disk drive unit is installed, to prevent a disk scan function from being performed (similar to windows os when the power is abruptly interrupted), it is important to follow the step sequence below when turning off the power switc...
Page 313
313 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 3. Turn the main power switch on the back of the machine to the off position. (this interrupts all the power to the machine) 4. Unplug the ac power cord. 8.12.3. Perform the following steps if the optional fax communication board (da-fg300) or the inte...
Page 314
314 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 e) confirm whether your machine is listed. If it is not listed, click "update" to access the web site and download the latest model module and then install it. Using the network address book editor to copy and paste the address book data 1. An appropria...
Page 315
315 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8.13. Installing the accounting software (da-wa10) 8.13.1. Contents note: 1. The part number may differ depending on the destination. 2. Refer to the parts list in the parts manual. 8.13.2. Installation 1. Before installing this option, make sure the h...
Page 316
316 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 8.14. Installing the dd server software (da-ws20) 8.14.1. Contents note: 1.The part number may differ depending on the destination. 2. Refer to the parts list in the parts manual. 8.14.2. Installation install the dd software into the pc with the operati...
Page 317
317 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8.15. Installing the expansion f-rom board (da-em600) 8.15.1. Contents note: 1.The part number may differ depending on the destination. 2. Refer to the parts list in the parts manual. 8.15.2. Installation caution! Turn the power switch on the left side...
Page 318
318 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (3) remove the black pin protector from slot 1 (cn62), if it was pre-installed. (4) install 2 pc board supporters for the slot 1 on the sc pc board. (5) install the program expansion board into slot 1 (cn62) on the sc pc board and secure with the suppor...
Page 319
319 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8.16. Installing the sorting image memory 16 / 64 / 128 mb (da-sm16b / 64b / 28b) 8.16.1. Contents note: 1.The part number may differ depending on the destination. 2. Refer to the parts list in the parts manual. 8.16.2. Installation caution! Turn the p...
Page 320
320 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (3) insert the sdrm pc board into the socket on the sc pc board as illustrated. Note: make sure to insert the sdrm pc board at a 20 - 30 ° angle into the memory socket, and then lock it down. (4) proceed with the installation of other options. If finish...
Page 321
321 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8.17. Installing the expansion flash memory card 4/8 mb (ue-410047/410048) 8.17.1. Contents note: 1.The part number may differ depending on the destination. 2. Refer to the parts list in the parts manual. 8.17.2. Installation caution! Turn the power sw...
Page 322
322 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 8.18. Installing the 3rd paper tray (da-ds303) / 4th paper tray (da-ds304) and the stand for 4-paper tray configuration (da-da230-pa) for dp-2310/3010 8.18.1. Contents 3rd paper tray 4th paper tray stand for 4-paper tray configuration note: this option ...
Page 323
323 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8.18.2. Installing the 3rd and 4th paper trays caution! Turn the power switch on the left side and the main power switch on the back of the machine to the off position, and then unplug the ac power cord before beginning installation. (1) slide the 4th ...
Page 324
324 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (5) join the caster and the 4th paper tray unit with the joint c plates (fr/rr), joint f plate (fl) and joint g plate (rl). (6) secure the joint c plates, joint f plate and joint g plate with 4 screws. (7) place the 3rd paper tray unit on the 4th paper ...
Page 325
325 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (15) place the machine on top of the 3rd paper tray unit as illustrated. Caution: the machine weights approximately 181 lb (82 kg) with the i-adf pre-installed. To prevent injuries, use the appropriate number of personnel and the proper equipment to li...
Page 326
326 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 8.19. Installing the 3rd paper tray (da-ds305) / 4th paper tray (da-ds306) and the stand for 4-paper tray configuration (da-da230-pa) for dp-2330/3030 8.19.1. Contents 3rd paper tray 4th paper tray stand for 4-paper tray configuration note: this option ...
Page 327
327 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8.19.2. Installing the 3rd and 4th paper trays caution! Turn the power switch on the left side and the main power switch on the back of the machine to the off position, and then unplug the ac power cord before beginning installation. (1) slide the 4th ...
Page 328
328 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (5) join the caster and the 4th paper tray unit with the joint c plates (fr/rr), joint f plate (fl) and joint g plate (rl). (6) secure the joint c plates, joint f plate and joint g plate with 4 screws. (7) place the 3rd paper tray unit on the 4th paper ...
Page 329
329 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (15) place the machine on top of the 3rd paper tray unit as illustrated. Caution: the machine weights approximately 181 lb (82 kg) with the i-adf pre-installed. To prevent injuries, use the appropriate number of personnel and the proper equipment to li...
Page 330
330 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 8.20. Installing the deluxe stand (da-da310 / da320) for usa only 8.20.1. Contents 8.20.2. Installation caution! Turn the power switch on the left side and the main power switch on the back of the machine to the off position, and then unplug the ac powe...
Page 331
331 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (4) place the machine on top of the deluxe stand as illustrated. Caution: the machine weights approximately 181 lb (82 kg) with the i-adf pre-installed. To prevent injuries, use the appropriate number of personnel and the proper equipment to lift or mo...
Page 332
332 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 8.21. Installing the stand (da-da310-pa / da320-pa) for dp-2310/3010 8.21.1. Contents 8.21.2. Installation caution! Turn the power switch on the left side and the main power switch on the back of the machine to the off position, and then unplug the ac p...
Page 333
333 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (2) remove 2 silver screws. (3) open the jam access cover. (4) remove the lower rear cover. (5) open the front cover of the stand. (6) open the 2nd paper tray. (7) connect the machine to the stand with 4 joint brackets. (8) secure each joint bracket wi...
Page 334
334 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 8.22. Installing the stand (da-da311-pa / da321-pa) for dp-2330/3030 8.22.1. Contents note: 1.The part number may differ depending on the destination. 2. Refer to the parts list in the parts manual. 8.22.2. Installation caution! Turn the power switch on...
Page 335
335 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (2) remove 2 silver screws. (3) open the jam access cover. (4) remove the lower rear cover. (5) open the front cover of the stand. (6) open the 2nd paper tray. (7) connect the machine to the stand with 4 joint brackets. (8) secure each joint bracket wi...
Page 336
336 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 8.23. Installing the 1-bin finisher (da-fs300) 8.23.1. Contents note: 1. The part number may differ depending on the destination. 2. Refer to the parts list in the parts manual. 3. Before you begin the installation of your 1 bin finisher (da-fs300), rea...
Page 337
337 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (1) open the right cover. (2) remove 2 silver screws. (3) remove the right rear cover. (4) remove 2 silver screws. (5) remove the lower rear cover. Caution: the opc drum is sensitive to light. To prevent optical exposure problems, do not expose the opc...
Page 338
338 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (13) secure the ground harness with 1 screw (xtw3+6lfc). (14) reinstall the hp cover. (15) secure the hp cover with 2 screws. (16) connect one harness to intermediate connector. (17) route the fns harness through the upper hole to the main pc board area...
Page 339
339 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (20) pull the fns harness from the bottom hole and secure with the harness clamp. (21) connect the harness to cn724 on the spc pc board. (22) install the finisher ipc pc board to cn725 on the spc pc board. (23) remove 2 shoulder silver screws (upper) a...
Page 340
340 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (27) release the pre-installed harness from the harness clamp. (28) install the optional lvps. (29) secure the optional lvps with 4 screws (xtw3+6lfc). (30) connect the lvs2 harness to cn64 on the optional lvps and to cn102 on acd pc board. (31) secure ...
Page 341
341 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (36) place the finisher on the base bracket. Note: make sure that 2 lock levers hook into the guide bracket properly. (37) install 2 slide guide brackets. (38) secure 2 slide guide brackets with 2 silver thumb screws (pf4124p023). (39) install the fini...
Page 342
342 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 8.24. Installing the exit tray [inner] (da-xn200) for dp-2310/3010 8.24.1. Contents 8.24.2. Installation caution! Turn the power switch on the left side and the main power switch on the back of the machine to the off position, and then unplug the ac pow...
Page 343
343 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (3) swing the paper holder to the left. (4) install the inner tray in the direction of the arrow holding up the paper holder. (5) plug the ac power cord into the wall outlet and turn the main power switch on the back and the power switch on the left si...
Page 344
344 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 8.25. Installing the exit tray [inner] (da-xn201) for dp-2330/3030 8.25.1. Contents note: 1.The part number may differ depending on the destination. 2. Refer to the parts list in the parts manual. 8.25.2. Installation caution! Turn the power switch on t...
Page 345
345 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (3) swing the paper holder to the left. (4) install the inner tray in the direction of the arrow holding up the paper holder. (5) plug the ac power cord into the wall outlet and turn the main power switch on the back and the power switch on the left si...
Page 346
346 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 8.26. Installing the exit tray [outer] (da-xt200) 8.26.1. Contents 8.26.2. Installation caution! Turn the power switch on the left side and the main power switch on the back of the machine to the off position, and then unplug the ac power cord before be...
Page 347
347 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (6) install the exit tray assembly onto the outer cover assembly. (7) plug the ac power cord into the wall outlet and turn the main power switch on the back and the power switch on the left side of the machine to the on position..
Page 348
348 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 8.27. Installing the automatic document feeder (da-as200) and the inverting automatic document feeder (da-ar250) for dp-2310/3010 8.27.1. Contents note: 1.The part number may differ depending on the destination. 2. Refer to the parts list in the parts m...
Page 349
349 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (3) install 2 thumb screws, one on each adf mounting bracket. Note: when installing the 2 thumb screws, do not tighten the screws. Keep about 6-8mm space as illustrated. (4) install the automatic document feeder on top of the adf mounting brackets. Not...
Page 350
350 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (12) connect the connector of the automatic document feeder unit. Note: be sure the connector is secured with the latch on both side. After connecting the connector of the automatic document feeder unit, secure the ground wire with 1 screw as illustrate...
Page 351
351 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (16) check the printed copy. If the printed image is skewed either to the right or left, adjust the adf position following the procedure below: a. Loosen the 5 screws securing the adf / i-adf. B. Using the hallmark on the right hinge base and the adf m...
Page 352
352 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (21) install the 2 hinge covers. Note: when installing the hinge covers, make sure that each hinge film is put inside of each hinge cover. (22) peel off the 6 adhesive protectors from the scanning pad. (23) place the scanning pad on the glass aligning o...
Page 353
353 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 document adjustment amount printed image adjustment remarks no.90 adf read main scan pos. No.92 orig. Trail edge adf no.91 original lead edge adf adjust the adf unit to scan the lined part (inside of the margin 1.5 - 2.5mm) on the document as shown on ...
Page 354
354 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 8.28. Installing the automatic document feeder (da-as201) and the inverting automatic document feeder (da-ar251) for dp-2330/3030 8.28.1. Contents note: 1.The part number may differ depending on the destination. 2. Refer to the parts list in the parts m...
Page 355
355 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (3) install 2 thumb screws, one on each adf mounting bracket. Note: when installing the 2 thumb screws, do not tighten the screws. Keep about 6-8mm space as illustrated. (4) install the automatic document feeder on top of the adf mounting brackets. Not...
Page 356
356 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (12) connect the connector of the automatic document feeder unit. Note: be sure the connector is secured with the latch on both side. After connecting the connector of the automatic document feeder unit, secure the ground wire with 1 screw as illustrate...
Page 357
357 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (16) check the printed copy. If the printed image is skewed either to the right or left, adjust the adf position following the procedure below: a. Loosen the 5 screws securing the adf / i-adf. B. Using the hallmark on the right hinge base and the adf m...
Page 358
358 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (21) install the 2 hinge covers. Note: when installing the hinge covers, make sure that each hinge film is put inside of each hinge cover. (22) peel off the 6 adhesive protectors from the scanning pad. (23) place the scanning pad on the glass aligning o...
Page 359
359 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 document adjustment amount printed image adjustment remarks no.90 adf read main scan pos. No.92 orig. Trail edge adf no.91 original lead edge adf adjust the adf unit to scan the lined part (inside of the margin 1.5 - 2.5mm) on the document as shown on ...
Page 360
360 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 8.29. Installing the platen cover (da-uc200) 8.29.1. Contents 8.29.2. Installation qty. Description part no. Remarks 1 platen cover dzma002394 1 scanning pad dzjm000428 2 platen hinge dzmh000013 4 screw xtb3+12j 1 installation instructions dzsm000303 th...
Page 361
361 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8.30. Installing the key counter harness kit (da-kh200) 8.30.1. Contents note: the key counter is sold separately. 8.30.2. Installation caution! Turn the power switch on the left side and the main power switch on the back of the machine to the off posi...
Page 362
362 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (6) connect the key harness into the kc harness. (7) connect the key harness to cn726 on the spc pc board. (8) insert the kc harness through the access hole of the rr frame. (9) secure the key harness with 3 harness clamps. (10) reinstall the right rear...
Page 363
363 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8.31. Installing the dehumidifier heater kit (dztq000048) 8.31.1. Contents dztq000048 note: 1. The part number may differ depending on the destination. 2. Refer to the parts list in the parts manual. No. Qty. Description part no. Remarks 1 1 pc board, ...
Page 364
364 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 8.31.2. Installation caution! Turn the power switch on the left side and the main power switch on the back of the machine to the off position, and then unplug the ac power cord before beginning installation. (1) remove the glass assembly. (refer to 2.2....
Page 365
365 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (9) install the emi bracket. (10) secure the emi bracket with 2 screws (xtb3+6j). (11) connect the ccd harness to the ccd pc board. (12) insert the ccd harness into the harness clamp. (13) secure the harness clamp with 1 screw (xtb3+6j). (14) remove 2 ...
Page 366
366 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (18) remove 2 silver screws. (19) remove the rear blind cover. (20) remove 2 silver screws. (21) remove the rear left cover. (22) mount the thermistor onto the heater bracket 2. (23) route the harness of the thermistor to lower section of the frame thro...
Page 367
367 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (30) remove 2 screws. (31) remove the nfl pc board. (32) route the ht1 harness to the lower section of the frame as illustrated. (33) connect the rlb harness to the nfl pc board (cn134). (34) reinstall the nfl pc board. (35) connect the ptc-ac harness ...
Page 368
368 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (37) connect the ptc-ac harness 3 to the ht3 harness. (38) insert the ht3 harness and ptc-ac harness 3 to 2 harness clamps. (39) route the ht3 harness to the lower section of the frame as illustrated. (40) mount the heater onto the heater bracket. (41) ...
Page 369
369 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (50) route the ptc-ac harness 3 to the lower section of the frame as illustrated. (51) close the rear cover. (52) remove the lower rear cover. (refer to 2.2.6. Of the service manual) (53) remove 2 screws. (54) remove the hp cover. (55) install the rlb ...
Page 370
370 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (61) connect the ht4 harness to the rlb pc board (cn172). (62) connect the ht3 harness to the ht4 harness. (63) connect the ht1 harness to the ht3 harness. (64) connect the ptc-ac harness 3 to the ht1 harness. (65) reinstall the hp cover. Note: when rei...
Page 371
371 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8.32. Installing the dehumidifier heater kit (dztq000049) 8.32.1. Contents note: 1. The part number may differ depending on the destination. 2. Refer to the parts list in the parts manual. No. Qty. Description part no. Remarks 1 1 heater ffpcp0035 2 1 ...
Page 372
372 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 8.32.2. Installation before installing the dehumidifier heater kit (dztq000049), make sure the dehumidifier heater kit (dztq000048) is installed in the unit first. Caution! Turn the power switch on the left side and the main power switch on the back of ...
Page 373
373 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (11) disconnect the cst2 harness from spc pc board (cn707). (12) close the rear cover. (13) release the cst2 harness from the harness clamp. (14) separate the 2nd paper feed module from the machine. Caution: the machine weights approximately 181 lb (82...
Page 374
374 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (16) install the heater assembly. (17) secure the heater assembly with 1 screw. (18) connect the heater assembly to the ht5 harness. (19) install the harness clamp. (20) insert the ht5 harness to the harness clamp. (21) remove 3 screws. (22) remove the ...
Page 375
375 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (27) place the machine on top of the 2nd paper feed module. Caution: the machine weights approximately 181 lb (82 kg) with the i-adf pre-installed. To prevent injuries, use the appropriate number of personnel and the proper equipment to lift or move th...
Page 376
376 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (1) open the right cover. (2) remove 2 silver screws. (3) remove the right rear cover. (4) remove 6 silver screws. (5) remove 3 lower rear covers. Caution: the opc drum is sensitive to light. To prevent optical exposure problems, do not expose the opc d...
Page 377
377 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (12) mount the heater onto the heater bracket. (13) install the heater assembly. (14) secure the heater assembly with 1 screw. (15) connect the heater assembly to the ht5 harness. (16) install the harness clamp. (17) insert the ht5 harness to the harne...
Page 378
378 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (23) pull the 3rd paper tray out. (24) install the protection sheet. (25) place the machine on top of the 3rd paper feed module. Caution: the machine weights approximately 181 lb (82 kg) with the i-adf pre-installed. To prevent injuries, use the appropr...
Page 379
379 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (31) connect the ht5 harness to the ht-cst harness. (32) connect the ht-cst harness to the ht2 harness. (33) install the harness clamp. (34) insert the harnesses to 2 harness clamps. (35) connect the cst3 harness to cst2 pc board (cn772). (36) reinstal...
Page 380
380 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (11) separate the 4th paper feed module from the machine. Caution: the machine weights approximately 181 lb (82 kg) with the i-adf pre-installed. To prevent injuries, use the appropriate number of personnel and the proper equipment to lift or move the m...
Page 381
381 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (20) route the ht6 harness and secure it into the harness clamp. (21) reinstall the protection plate. (22) pull the 4th paper tray out. (23) install the protection sheet. (24) place the machine on top of the 4th paper feed module. Caution: the machine ...
Page 382
382 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (28) connect the ht2 harness to the rlb pc board (cn174). (29) reinstall the hp cover. (30) connect the ht6 harness to the ht2 harness. (31) install 2 harness clamps. (32) insert the ht6 harness into 3 harness clamps. (33) connect the cst2 harness to cs...
Page 383
383 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8.33. Replacing the opc drum (1) open the right cover. (2) remove 1 screw. (3) remove the harness cover. (4) unlock the angled rear arm and the front arm. (5) open the right cover and hook the angled rear arm into the lower hook hole. (6) open the fron...
Page 384
384 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (10) disconnect the harness. (11) loosen 1 screw. (12) slide the process unit out. Caution: to prevent damage to the process unit, ensure the right cover is still open before pulling the process unit out. Caution: exercise caution not to scratch the sur...
Page 385
385 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (18) remove the opc drum shaft holder assembly. (19) remove the front dsd arm. (20) lift the opc drum, holding the right side where the opc drum shaft holder assembly was installed. (21) clean the bias charge roller with a soft dry cloth that came with...
Page 386
386 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (24) ensure that the opc drum is fully coated with the drum starting powder. Apply additional drum starting powder onto the surface of the opc drum if required. Note: do not touch the surface of the opc drum with bare hands when removing or reinstalling...
Page 387
387 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8.34. Replacing the laser unit (lsu) (1) open the right cover. (2) remove 1 screw. (3) remove the harness cover. (4) unlock the angled rear arm and the front arm. (5) open the right cover and hook the angled rear arm into the lower hook hole. (6) open ...
Page 388
388 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (10) disconnect the harness. (11) loosen 1 screw. (12) slide the process unit out. Caution: to prevent damage to the process unit, ensure the right cover is still open before pulling the process unit out. Caution: exercise caution not to scratch the sur...
Page 389
389 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 8.34.1. Laser power (pwm circuit) adjustment (19) disconnect 3 harnesses. (20) remove 3 screws. (21) remove the lsu unit. (22) install the new lsu unit. (1) ensure that ledger / a3 size paper is loaded in one of the trays, and pull the other trays out....
Page 390
390 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 8.34.2. Lsu skew adjustment (1) remove the front left cover. (refer to "replacing the lsu", steps (1) ~ (15)) (2) loosen 4 red screws. Adjust the lever plate downwards and recheck the document skewing. Readjust as needed. One scale adjusts the skewed im...
Page 391
391 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 9 general network information 9.1. Network protocol 9.1.1. Osi reference mode having a model in mind helps you understand how the pieces of the network puzzle fit together. The most commonly used model is the open system interconnection (osi) reference...
Page 392
392 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 9.1.2. Protocol one reason for the popularity of tcp/ip is that no one vendor owns it, unlike the ipx/spx, dna, sna or apple talk protocol suites, all of which are controlled by specific companies. Tcp/ip evolved in response to input from a wide variety...
Page 393
393 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 9.2. Layer functions and technology 9.2.1. Mac (media access control) the mac address is burnt into each network card for establishing addresses for nodes on the network. These addresses are hexadecimal in nature and are unique for each card. The first...
Page 394
394 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 a computer in the ring captures the token, if it has data to transmit, it holds the token and transmits a data frame. This data frame is passed to each computer in the ring, which checks whether it is the intended recipient of the frame. When the frame ...
Page 395
395 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 9.2.3. Ethernet ethernet is a very popular local area network architecture based on the csma/cd access method. The original ethernet specification was the basis for the ieee 802.3 specifications. Typically, ethernet networks can use a bus physical topo...
Page 396
396 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 all eight pins on the ethernet cable are normally wired in this configuration accordingly. The electrical level follows the manchester code configuration. Out of balance in electrical levels indicates that a collision is occurring in a certain area. To ...
Page 397
397 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 9.3. Network layer 9.3.1. Ip address an ip address is a set of four numbers, or octets, that can range in value between 0 and 255. Each octet is separated by a period (i.E. 192.168.31.1). All devices on a network that runs the tcp/ip protocol suite nee...
Page 398
398 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 9.3.2. Subnet mask a subnet mask defines how sub-segments of a network are treated. For network management purposes, special ip addresses are assigned. 1. Host address is set to all “0” 2. Host address is set to all “1” reserved for ip broadcasting to a...
Page 399
399 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 9.3.3. Internet protocol the ip (internet protocol) operating at the osi network layer, is a connectionless protocol that provides datagram service, and ip packets are most commonly referred to as ip data grams. It performs the following typical functi...
Page 400
400 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 9.3.4. Router routers, operating at the osi network layer, organize the large network in terms of logical network segments. Each network segment is assigned an address so that every packet has both a destination network address and a destination device ...
Page 401
401 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 9.4. Transport layer 9.4.1. Tcp (transmission control protocol) the tcp (transmission control protocol) is an internetwork connection-oriented protocol that corresponds to the osi transport layer. Tcp provides full-duplex, end-to-end connections. When ...
Page 402
402 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 the client generates random sequential numbers initially and sends them to the server. The initial sequential numbers are synchronized with the clock and increments the counter every 4 msec. The server responds with an acknowledgement that increments th...
Page 403
403 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 9.5. Upper layer 9.5.1. Dns (domain name system) the dns (domain name system) protocol provides host name and ip address resolution as a service to client applications. Dns servers enable humans to use logical node names, utilizing a fully qualified do...
Page 404
404 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 the name resolution flow is shown in the illustration above and follows the sequence below: 1. Query the local dns server. 2. Query the root dns server because the domain belongs to a destination outside of the company. 3. The “com” root dns server send...
Page 405
405 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 9.5.4. Soa (start of authority) record each database file starts with a start of authority (soa) record for the file. This record specifies the zone's primary server, the server that maintains the read/write copy of the file. The syntax of this record ...
Page 406
406 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 9.5.5. A (address) record the a (address) record, lists the addresses for a given machine. The name field is the machine’s name and the address is the network address. There should be one a record for each address on the machine. 9.5.6. Ptr (pointer) re...
Page 407
407 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 9.5.8. Ns (name server) record the name server record specifies the other name servers for a domain. The syntax for a name server record is shown below: in ns an example of a name server record follows below: @ in ns nwmgr.Pcc.Co.Jp the "@" symbol indi...
Page 408
408 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 9.6. Smtp (simple mail transfer protocol) the objective of simple mail transfer protocol (smtp) is to transfer mail reliably and efficiently. Smtp is independent of the particular transmission subsystem and requires only a reliable ordered data stream c...
Page 409
409 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 9.7. Itu t.37 and rfc2305 9.7.1. Mode of operation the unit conforms to the itu t.37 standards and rfc2305. This internet store and forward facsimile uses approved ietf protocols for posting, relaying and delivery of documents. It requires no changes t...
Page 410
410 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 offramp gateway (when implemented) 9.7.3. Definitions and abbreviations rfc reference http://www.Imc.Org/ietf-fax/ required be smtp compliant provide delivery failure notification be able to process pstn/fax email address comply with the relevant itu re...
Page 411
411 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 9.7.4. File format for internet fax sending internet fax devices must be able to write minimum set tiff files, according to the rules for creating minimum set tiff files defined in tiff for facsimile (the s profile) [rfc2301], which is also compatible ...
Page 412
412 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 9.7.5. Minimal set the minimum interchange set of tiff fields that must be supported by all implementations in order to assure that some form of an image, albeit black-and-white, can be interchanged. The table below summarizes the tiff fields that compr...
Page 413
413 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 note: for rfc2305, a pstn address in an email address should follow the above style. The key words “must”, “must not”, “required”, “shall”, “shall not”, “should”, “should not”, “recommended”, “may”, and “optional” in this document are to be interpreted...
Page 414
414 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 9.7.8. Delivery failure in the event of relay failure, the sending relay must generate a failure message, which should be in the format of a dsn. 9.7.9. Image file format the sending internet fax devices must be able to write minimum set tiff files, acc...
Page 415
415 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 9.8. Communication protocols the set of conventions necessary to achieve facsimile-compatible service covers basic data transport, document data formats, message (document) addressing, delivery confirmation, and message security. Protocol supported by ...
Page 416
416 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 9.8.1. Opening and closing at the time the transmission channel is opened there is an exchange of commands to ensure that the hosts are communicating with the hosts they think they are. The following two commands are used in the transmission channel for...
Page 417
417 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 9.8.10. Numeric order list of reply codes 211 system status or system help reply 220 service ready 221 service closing transmission channel 250 requested mail action okay# completed 251 user not local; will forward to 354 start mail input; end with . 4...
Page 418
418 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 9.9. Pop (post office protocol version 3) 9.9.1. Introduction on certain types of smaller nodes in the internet it is often impractical to maintain a message transport system (mts). For example, a workstation may not have sufficient resources (cycles, d...
Page 419
419 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 a pop3 server may have an inactivity auto logout timer. Such a timer must be of at least 10 minutes’ duration. The receipt of any command from the client during that interval should suffice to reset the auto logout timer. When the timer expires, the se...
Page 420
420 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 opening tcp connection (tcp port no. 110) +ok pop server ready your panasonic device (ef1.Labo.Pcc.Com) pop 3 server (sv2.Labo.Pcc.Com) pop 3 command & reply procedure user s50055 dele 1 closing tcp connection (port no. 110) tcp 3 way handshake & openin...
Page 421
421 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 9.10. Troubleshooting from a pc troubleshooting is an art of seeking out the cause of a problem and eliminating the problem by managing of eliminating the cause. No matter what the problem is on your network, the osi reference model serves as an excell...
Page 422
422 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 9.11. Verifying the configuration and mail account type (smtp or pop) start is the lan connected to an isp is this a dialup connection ? Yes is static ip address available ? No no is g3 gateway function being used ? Yes no yes is pop account available ?...
Page 423
423 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 9.12. Dynamic host configuration protocol (dhcp) - extended feature dhcp is based on the bootstrap protocol (bootp), adding the capability of automatic allocation of reusable network addresses and additional configuration options. The dynamic host conf...
Page 424
424 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 following figure shows the timeline diagram of messages exchanged between dhcp client and servers when allocating a new network address. Following figure shows the timeline diagram of messages exchanged between dhcp client and servers when reusing a pre...
Page 425
425 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 several options have been defined so far. One particular option - the "dhcp message type" option - must be included in every dhcp message. This option defines the "type" of the dhcp message. Additional options may be allowed, required, or not allowed, ...
Page 426
426 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 9.13. Message disposition notifications (mdn) - extended feature the confirmation of delivery and processing are extensions to "simple mode of facsimile using internet mail" [rfc2305]. These are designed to be interoperable with the existing base of mai...
Page 427
427 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 for example, you may configure the mdn parameter from options menu of outlook express. Additional document capabilities section 4 of "a simple mode of facsimile using internet mail" [rfc2305] allows sending only the minimum subset of tiff for facsimile...
Page 428
428 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (2) recipient's mdn response recipient (internet fax) starts printing process when the message is received properly. If the disposition-notification-to field is contained in message, recipient generates mdn capability response after successful delivery ...
Page 429
429 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (3) processing confirmation the processing confirmation provided by recipient is received and take specific services for expected several conditions respectively. This is unit independent issue. To see more detailed information, please refer to rfc2532...
Page 430
430 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 9.14. Lightweight directory access protocol (ldap) - extended feature the protocol is designed to provide access to directories supporting the x.500 models, while not incurring the resource requirements of the x.500 directory access protocol (dap). This...
Page 431
431 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 the pop3 client makes note of this timestamp, and then issues the apop command. The "name'' parameter has identical semantics to the "name" parameter of the user command. The "digest" parameter is calculated by applying the md5 algorithm to a string co...
Page 432
432 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 9.16. Smtp service extension for authentication (smtp auth) - extended feature smtp is widely deployed and high-quality implementations have proven to be very robust. However, the internet community now considers some services to be important that smtp ...
Page 433
433 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 containing a base64 encoded string. If the client wishes to cancel an authentication exchange, it issues a line with a single "*". If the server receives such an answer, it must reject the auth command by sending a 501 reply. If the server cannot base6...
Page 434
434 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 9.17. Direct internet fax xmt - extended feature direct internet fax xmt uses simple mail transfer protocol (smtp) to transfer mail reliably and efficiently. An important feature of smtp is its capability to transport mail across networks, usually refer...
Page 435
435 dp-2310/3010 mar 2005 ver. 2.1 dp-2330/3030 10 schematic diagram 10.1. General circuit diagram 1 2 3 4 5 6 7 8 9 10 11 12 13 cn726 1 2 3 4 5 1 2 3 4 13 14 15 16 17 cn225 lcd t ouch p anel pnl2 pnl1 cn220 cn52 cn656 1 2 3 cn657 fuser lamp 1 fuser lamp 2 tst tfu m lsu motor cn708 cn702 cn144 cn711...
Page 436
436 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 10.2. Finisher circuit diagram cont 1 2 3 1 2 3 4 5 cn1 cn7 cn4 cn6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 2 3 4 5 6 7 8 9 10 11 1 2 3 4 5 6 7 8 9 10 11 cn10 1 2 3 4 5 6 7 8 9 cn5 1 2 3 4 5 6 7 8 1 2 3 4 5 6 cn2 1 2 3 4 5 6 i/f connect or 1 2 3 4 5 6 7 8 9...
Page 437
437 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 11 finisher option (da-fs300) 11.1. General description 11.1.1. Features 1. Compact and light weight 2. Sorting and stapling by shift-sort sheet stacking, matching, offset stacking, and stapling are performed on a halfway-processing tray. 3. Stack tray...
Page 438
438 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 note 1 : the number of sheets is computed based on 80 g/m2 paper. Note 2 : alignment is not guaranteed if the stack consists of sheets of different sizes or staple/shift-sort modes. Stapling position: stapling position rear 1-point stapling refer to the...
Page 439
439 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 11.1.3. Electrical components 11.1.4. Routine maintenance by the user name notation description motor 1 feed motor 2 alignment motor 3 stack tray elevation motor solenoid 4 paddle solenoid 5 large gear solenoid 6 paper detection solenoid stapler unit 7...
Page 440
440 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 11.2. Maintenance and inspection 11.2.1. Periodic part replacement the unit does not have components that require periodical replacement. 11.2.2. Consumables and durables some components may require replacement due to wear, deterioration or damage. Repl...
Page 441
441 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 11.2.3. Disassembly and assembly (1) open and hold the finisher cover (2608). (2) release the front and rear arms (2609 and 2610). (3) release the rear latch and remove the finisher cover (2608). (4) remove 1 screw (2633). (5) remove the front cover as...
Page 442
442 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (10) remove 2 screws (2632) and 2 washers (2634). (11) remove the right cover (2604). (12) lift the pcb cover mylar (2635) up. (13) disconnect all the harnesses on the cont pc board. (14) remove 1 screw (2633). (15) remove the cont pc board (3028). (16)...
Page 443
443 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (18) disconnect the harness. (19) remove 1 screw (2521) and 1 screw (2631). (20) remove the guide base (2832) assembly. (21) release the tension spring (3024) and latch, and then remove the lock arm (3025). (22) remove the tension spring (3024). (23) r...
Page 444
444 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (27) remove the upper guide assembly as illustrated. Note: when reinstalling, rotate the timing belt counter-clockwise and then fasten 1 screw. (28) remove 1 snap ring (2734). (29) remove the feed roller gear (2702). (30) remove the bushing (2919). (31)...
Page 445
445 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (32) remove the feed arm assembly (2913). (33) remove 1 screw (2521) and 1 screw (2633). (34) remove the tray guide assembly (2611). (35) disconnect 3 harnesses (2629). Note: when reinstalling, ensure that the harnesses are connected correctly as illus...
Page 446
446 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (36) remove 1 snap ring (2734). (37) remove the exit roller gear (2701). (38) remove the bushing (2919). (39) lift up the guide base (2801) assembly. (40) lift up the paper guide (2921). (41) remove the exit roller assembly (2936) as illustrated. (42) r...
Page 447
447 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (46) remove 2 screws (2521). (47) remove the staple unit (2938) assembly. Note: when reinstalling, ensure that staple unit assembly is installed (hooked) correctly as illustrated. (48) remove 2 screws (2736). (49) loosen 1 screw. (50) remove the staple...
Page 448
448 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 (54) disconnect the harness. (55) remove 2 screws (3030). (56) remove the sensor hold bracket (3008). (57) remove 2 screws (2633). (58) remove the drive motor (3014). (59) disconnect the harness. (60) release the harness from the clamp. (61) remove 4 sc...
Page 449
449 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 (64) remove 2 screws (2521). (65) remove the set motor (2931) assembly. (66) disconnect 2 harnesses. (67) release the harness from the clamp. Note: when reinstalling, ensure that the harnesses are connected correctly as illustrated. (68) remove 2 screw...
Page 450
450 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 11.3. Operation and system description 11.3.1. Outline of operation da-ds330 and host machine exchange signals through serial communication and carry out the following 3 operation modes. • normal exit discharge the paper into the stack tray. • staple ex...
Page 451
451 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 11.3.3. Electrical parts (motor and solenoid functions) 11.3.3.1. Feed motor control 1. Feed motor, which moves paper feed, paddle drive, stack delivery unit elevation, is 1-2 phase exciting type, 2 phase stepping motor. Its control circuit is shown be...
Page 452
452 dp-2330/3030 mar 2005 ver.2.1 dp-2310/3010 11.3.3.3. Elevation motor control 1. Elevation motor, which moves stack tray up and down, is a +24v dc brush motor. The control circuit is shown below. 2. It is controlled by the combination of signals from p52 and p53 of ic2 in p.C.B. (pba-cont). Stack...
Page 453
453 dp-2330/3030 mar 2005 ver. 2.1 dp-2310/3010 11.3.3.5. Large gear solenoid control 1. An up-and-down motion of the delivery unit is performed by changing the drive of feed motor, which is controlled by the large gear solenoid. If the large gear solenoid is turned on during rotation of the feed mo...
Page 454
Memo.
Page 455: Operating Instructions
88 panasonic ® software operating instructions network firmware update tool (service tool) version 3 dzsd001829-9.
Page 456
Network firmware update tool (lan) table of contents 1. General 3 1.1 supporting os.......................................................................................................................................... 3 1.2 supporting panasonic fax/copier models.....................................
Page 457
Network firmware update tool (lan) 1. General the network firmware update tool allows a panasonic fax/copy machine connected via lan (tcp/ip) to program the firmware code memory of the unit directly. Using a pc, the firmware code is transferred to the firmware code memory of the unit through the lan...
Page 458
Network firmware update tool (lan) 2. Installation 2.1 installing the network firmware update tool 1. Start microsoft windows. For windows nt 4.0 / 2000 / xp, logon to the computer/network with an account that can add or change configurations (i.E. Administrator). 2. Run \xfirmware\toolswfirmup\se...
Page 459
Network firmware update tool (lan) 2.3 uninstalling the network firmware update tool the network firmware update tool can be uninstalled by using its uninstall program. Note: do not delete the installed program folder from windows explorer directly, due to possible registry setting problems. 1. Star...
Page 460
Network firmware update tool (lan) 3. Preparing the firmware update 3.1 preparing the unit to accept the firmware code 3.1.1 for dx-600 / dx-800 (v1.31 or higher) 1. If the device password is changed (remote password) from the default value (blank = 0000), it is not possible to program the firmware ...
Page 461
Network firmware update tool (lan) 4. Using the network firmware update tool 1. Please close the all applications that are currently running. Note: about windows 2000/xp, using network firmware update tool, the authority more than a power user is required. 2. From the windows desktop, double-click o...
Page 462
Network firmware update tool (lan) 4. Enter the destination device(s) by using manual input or device address list. Click [ok]. 5. Confirm the destination device(s). Click [next>]. Page 8.
Page 463
Network firmware update tool (lan) 6 specify the firmware code file using the following methods. Select an archive file (complete set) --> step 6a1 you can select the firmware code archive file directly here. The selected archive file will be extracted into the local \data folder automatically and i...
Page 464
Network firmware update tool (lan) 6a2 select the firmware archive file and click [open]. Ex. Dp-2310_3010_pu_030228.Exe 6a3 extracting... 6a4 select the firmware type window appears. Select the firmware type and click [ok]. 6a5 firmware code file selection is completed. Click [next>]. Page 10
Page 465
Network firmware update tool (lan) 6b1 select a parent file folder (complete set) select "select a parent file folder (complete set)" and click [browse...] button. 6b2 select the parent file folder and click [ok]. Ex. \dp-2310_3010_pu_030228 6b3 select the firmware type and click [ok]. Page 11.
Page 466
Network firmware update tool (lan) 6b4 firmware code file selection is completed. Click [next>]. 6c1 select independent file folders select "select independent file folders" and click [browse...] button. 6c2 select the firmware code file folder and click [ok]. Ex. Sfdl2pnlaav100000_pu.Bin page 12.
Page 467
Network firmware update tool (lan) 6c3 select the other firmware code file folder and click [ok]. 6c4 firmware code file selection is completed. Click [next>]. 7. The version check for the specified devices starts. Click [next>]. Page 13.
Page 468
Network firmware update tool (lan) 8. Verify that the information you want to update is correct. Then click [next>]. Note: the firmware of pnl, sc and spc are transmitted separately and each time the unit erases, writes and reboots in the normal mode. If you check "send at once", all firmware will b...
Page 469
Network firmware update tool (lan) 11. When the transfers are completed, all jobs in the spooler disappear and the communication log is displayed. Click [finish] to close the tool. After each firmware code is successfully programmed to the firmware flash memory in the unit, the unit reboots and rest...
Page 470
Memo.
Page 471: Operating Instructions
Panasonic ® software operating instructions local firmware update tool (service tool) version 3 dzsd000965-14.
Page 472
Local firmware update tool (parallel /usb port) table of contents 1. General 3 1.1 supporting os.......................................................................................................................................... 3 1.2 supporting panasonic fax/copier models........................
Page 473
Local firmware update tool (parallel/usb port) 1. General the local firmware update tool (parallel/usb) allows a panasonic fax/copy machine to emulate a flash memory card writer and create a master firmware card, or to program the firmware code memory of the unit directly. Using a pc, the firmware c...
Page 474
Local firmware update tool (parallel /usb port) 2. Installation 2.1 installing the hardware on the panasonic fax/copy machine 1 depending on the model, a parallel port or usb port is installed. Please install the parallel port/usb port assembly into one of the supporting panasonic fax/copier models ...
Page 475
Local firmware update tool (parallel/usb port) 5 copying... 6 the installation is completed. Check “yes, i want to …” and click [finish] to restart your pc. 2.3 installing usb firmware update driver (for the usb port model only) 1 after installation of the local firmware update tool, if you need to ...
Page 476
Local firmware update tool (parallel /usb port) 2.4 uninstalling the local firmware update tool the local firmware update tool can be uninstalled by using its uninstall program. Note: do not delete the installed program folder from windows explorer directly, due to possible registry setting problems...
Page 477
Local firmware update tool (parallel/usb port) 3. Preparing the firmware update 3.1 preparing the unit to accept the firmware code please refer to the service manual to set the unit to firmware update mode (service mode). 3.2 preparing the firmware code copy the firmware code file(s) to the followin...
Page 478
Local firmware update tool (parallel /usb port) 4. Using the local firmware update tool 1 set the machine to the firmware update mode and then connect the unit and pc with a parallel cable or usb cable. Note: for the usb port models, the plug & play of the printer mode is activated when the usb cabl...
Page 479
Local firmware update tool (parallel/usb port) 5 specify the firmware code file by the following methods. Select an archive file (complete set) --> step 5a1 you can select the firmware code archive file directly here. The selected archive file will be extracted into the local \data folder automatica...
Page 480
Local firmware update tool (parallel /usb port) 5a4 select the firmware type window appears. Select the firmware type and click [ok]. 5a5 firmware code file selection is completed. Click [next>]. Page 10
Page 481
Local firmware update tool (parallel/usb port) 5b1 select a parent file folder (complete set) select "select a parent file folder (complete set)" and click [browse...] button. 5b2 select the parent file folder and click [ok]. Ex. \dp-2310_3010_pu_030327 5b3 select the firmware type and click [ok]. P...
Page 482
Local firmware update tool (parallel /usb port) 5b4 firmware code file selection is completed. Click [next>]. Page 12.
Page 483
Local firmware update tool (parallel/usb port) 5c1 select an independent file select "select an independent file" and click [browse...] button. 5c2 select the firmware code file and click [open]. Ex. Sfdl2pnlaav100000_pu.Bin 5c3 firmware code file selection is completed. Click [next>]. Page 13.
Page 484
Local firmware update tool (parallel /usb port) 6 the selected firmware code file(s) are indicated. Uncheck the box if you do not need to transfer a file. On the unit side: set the unit to the firmware update mode. Click [next>]. 7 the firmware code file starts transferring. When there is more than ...
Page 485
Local firmware update tool (parallel/usb port) unit information of the firmware update mode: for usb connected unit (dp-2310/3010): every time the machine finishes receiving a firmware code file, the unit does the delete and rewrite of the firmware code and will return to service mode again. Set the...
Page 486
Dzzsm00270