1. DL manuals
  2. Panasonic
  3. Accessories
  4. KX-HNS101E
  5. Installation Manual

Panasonic KX-HNS101E Installation Manual

Other manuals for KX-HNS101E: Installation Manual
Manual is about: Home Network System Window/Door Sensor

Summary of KX-HNS101E

  • Page 1

    Installation guide home network system window/door sensor model no. Kx-hns101e thank you for purchasing a panasonic product. This document explains how to install the window/door sensor properly. For details about how to use the system, refer to the user’s guide (page 19). Please read this document ...

  • Page 2: Introduction

    Introduction accessory information ...............3 general information ...................4 important information about this system ......................5 for your safety ...........................5 important safety instructions ......6 for best performance ................6 other information ......

  • Page 3: Accessory Information

    Accessory information supplied accessories no. Accessory item/part number quantity a battery *1 1 b mounting screws (20 mm) *2 /xmm38+20vw 4 c mounting double-sided tapes *3 3 *1 when replacing the battery, see “power source” of “specifications”, page 20 for battery information. *2 2 screws for the ...

  • Page 4: General Information

    Direct sales at panasonic u.K. R order accessory and consumable items for your product with ease and confidence by phoning our customer communications centre monday - friday 9:00am - 5:00pm (excluding public holidays). R go on line through our internet accessory ordering application at www.Pas-europ...

  • Page 5: About This System

    About this system r this system is an auxiliary system; it is not designed to provide complete protection from property loss. Panasonic will not be held responsible in the event that property loss occurs while this system is in operation. R the system’s wireless features are subject to interference,...

  • Page 6: Caution

    R if any electrolyte should come into contact with your hands or clothes, wash it off thoroughly with water. R if any electrolyte should come into contact with your eyes, never rub your eyes. Rinse your eyes thoroughly with water, and then consult a doctor. Caution general information r do not place...

  • Page 7: Other Information

    – away from electronic appliances such as tvs, radios, personal computers, wireless devices, or other phones. – facing away from radio frequency transmitters, such as external antennas of mobile phone cell stations. (avoid putting the hub on a bay window or near a window.) r if the reception for a h...

  • Page 8: Important Information

    Note for the battery symbol this symbol ( b ) might be used in combination with a chemical symbol. In this case it complies with the requirement set by the directive for the chemical involved. Note for the battery removal procedure refer to “inserting the battery” on page 10. 8 helpline tel. No.: u....

  • Page 9: Part Names And

    Part names and functions n sensor unit n magnet unit d b c a e e sensor unit cover m n used to confirm the status of the sensor or register the sensor to the hub. Led indicator magnet unit cover “ ” marks used to align the sensor and the magnet unit when installing them (page 13). Led indicator you ...

  • Page 10: Inserting The Battery

    Desired installation area is suitable to proper operation. 5 temporary placement temporarily place the window/ door sensor in the desired location and confirm that it operates properly (page 13). 6 installation install the window/door sensor on the same position where proper operation was confirmed ...

  • Page 11: Registering The

    Registering the window/door sensor this procedure is not required for devices that were included as part of a bundle. Before you can use the window/door sensor, it must be registered to the hub. If you purchased devices separately (i.E., not as part of a bundle), you must register each device to the...

  • Page 12: Wireless

    Wireless communication range the wireless communication range of each device in the system from the hub is approximately 50 m indoors and approximately 300 m outdoors. Wireless communication may be unreliable when the following obstacles are located between the hub and other devices. R metal doors o...

  • Page 13: Temporary Placement

    Temporary placement before installing the window/door sensor, temporarily place it in the desired location and confirm that it operates properly by pressing m n . Important: r attach the sensor unit to the window frame or door frame, and attach the magnet unit to the window or door. R the window/doo...

  • Page 14: Setup

    Example 1: installed on the left side of a window correct 1 a b green 1 “ ” marks point directly at each other and are within 25.4 mm of each other. Result: when you press m n ( a ), the led indicator lights in green ( b ). Incorrect 2 3 4 a b red 2 “ ” marks are aligned but units are too far apart....

  • Page 15: Setup

    Example 2: installed on the right side of a window correct 1 a b green 1 “ ” marks point directly at each other and are within 25.4 mm of each other. Result: when you press m n ( a ), the led indicator lights in green ( b ). Incorrect 2 3 4 a b red 2 “ ” marks are aligned but units are too far apart...

  • Page 16: Installation

    Installation install the window/door sensor in the same position where proper operation was confirmed (page 13). You can install the window/door sensor using screws or double-sided tape, depending on your preference or the material of the installation area. Note: r when installing, make sure the bat...

  • Page 17: Setup

    2 sensor unit: attach the sensor unit. 1 screws 2 86.2 mm magnet unit: attach the magnet unit. 3 screws 4 24.4 mm 2 4 1 1 3 3 5 3 attach the covers. Important: r 5 align the “ ” marks on the sensor unit and the magnet unit so that they point directly at each other and are no more than 25.4 mm apart....

  • Page 18: Setup

    Securing with double-sided tape note: r make sure the surfaces of the sensor unit, magnet unit, and the installation area are clean and dry before applying double-sided tape. 1 check that the sensor unit cover and magnet unit cover are attached. 2 affix double-sided tape to the sensor unit and magne...

  • Page 19: Testing The Window/

    Testing the window/ door sensor you can check the window/door sensor’s led indicator and test the performance of the window/door sensor. 1 remove the sensor unit cover. 2 press m n on the sensor unit. 3 open and close the window or door several times. R make sure that the led indicator lights in gre...

  • Page 20: Specifications

    Specifications r standards dect (digital enhanced cordless telecommunications) r frequency range dect: 1.88 ghz – 1.90 ghz r rf transmission power approx. 10 mw (average power per channel) r power source lithium battery cr2 (1 ´ 3.0 v, 850 mah) r operating conditions -10 °c – 40 °c r battery life up...

  • Page 21: Conditions Of Guarantee

    Conditions of guarantee receipt no. Model no. Date of purchase serial no. This guarantee is in addition to and does not in any way affect any statutory or other rights of consumer purchasers. If within the applicable guarantee period, the product proves to be defective by reason of faulty design, wo...

  • Page 22: Notes

    22 notes hns101e_(en_en)_0421_ver.060.Pdf 22 2015/04/21 14:21:42.

  • Page 23: Notes

    23 notes hns101e_(en_en)_0421_ver.060.Pdf 23 2015/04/21 14:21:42.

  • Page 24: Use Cr2 Lithium Battery.

    1 use cr2 lithium battery. 2 use the home network app to access the user’s guide and refer to the troubleshooting section. Important! If your product is not working properly. . . If you still have any problems, please call the helpline 0330 3331112 (u.K.) 01 4475228 (ireland) or contact us through o...