Summary of SD-257WST
Page 1
© panasonic corporation 2010 unauthorized copy- ing and distribution is a violation of law. Orderno.Ptw1003508ce automatic bread maker model no. Sd-257wst chassis product color white destination australia table of contents page page 1 safety precautions-----------------------------------------------...
Page 2: 1 Safety Precautions
2 1 safety precautions.
Page 3: 2 Specifications
3 2 specifications power supply 230-240v -50 hz power consumed 505-550 w capacity (strong flour for a loaf) max.550g min.400g (strong flour for a dough) max.600g min.250g (yeast) max.8g min.0.75g capacity of raisin nut dispenser max.150g dried fruit/nuts timer digital timer (up to 13 hours) dimensio...
Page 4
4 3 location of controls and components.
Page 5
5.
Page 6: 4 Operating Instructions
6 4 operating instructions.
Page 7
7.
Page 8
8.
Page 9
9.
Page 10
10
Page 11
11.
Page 12
12.
Page 13: 5 Test Mode
13 5 test mode 5.1. Key operation and check mode before trobleshooting, operate the checkmode in the following procedure. 5.1.1. Check mode 5.1.1.1. Electric power breakdown mode when an electric power breakdown is detected, all load of the device goes off in this mode. Behavior of device after rest...
Page 14
14 5.1.1.2. Sensor disconnection mode when the disconnection of a sensor is detected, all load of the device goes off in this mode. Indication on lcd • "h01" is displayed on the lcd during the sensor disconnec- tion. ("h01" is brinking) 5.1.1.3. High temperature alarm mode when the "start" key is pr...
Page 15: 6 Troubleshooting Guide
15 6 troubleshooting guide before troubleshooting, operate the main body test mode in the following procedure in order to check the p.C.Boards. 6.1. Main body test mode 6.1.1. Setting the main body initial test mode operation procedure 1. Insert the power cord plug into an electrical outlet. 2. Pres...
Page 16
16 6.1.3. Solenoid/motor operation test (volume.2) mode operation procedure 1. Press the "timer" key. Phenomena • lcd indication: it light up like the right figure. • behaviour of device: the solenoid runs for 1 second and stops for 1 second. Then the motor runs and stops in the manner of 0.5 sec on...
Page 17
17 7 disassembly and assembly instructions important: • refer to the tips on assembly, and carry out the disassembly procedure backward to assembly. • remove the bread pan assy and kneading blade b unit before disassembling. 7.1. Dispenser cover assy 1. Remove the dispenser cover from the hinge part...
Page 18
18 7.2. Top lid assy 1. Detach the hinge screw. 2. Slide the top lid assy and remove it from its hinge part..
Page 19
19 3. Remove 3 screws from the inner lid. 4. Remove the inner lid with the ( - ) top screw driver wrenching into the chink between the top lid assy and the inner lid. * the inner lid is held with the top lid assy by 8 locks. 5. Remove dispenser b assy. 6. Remove the screw and detach the lid lever b,...
Page 20
20 7.3. Control panel unit 1. Remove 2 screws. 2. Unlock the control panel inner lid from the upper frame lock part while lifting the control panel unit, and while pushing 2 square holes with ( - ) top screw driver. 3. Remove the control panel unit from the locks on the body while pulling and pushin...
Page 21
21 7.4. Solenoid assy b 1. Remove the screw and detach the solenoid assy b, sole- noid fixing plate and spring a..
Page 22
22 7.5. P.C.Board a 1. Remove 2 screws and detach p.C.B cover. 2. Disconnect the flat cable and lead wire from p.C.Board a. 3. Remove the p.C.Board a from the p.C.B cover..
Page 23
23 7.6. Body and others 1. Remove 4 screws for rubber leg fixing, and detach the rubber legs. 2. Remove 2 screws and detach the cord support. 3. Remove the glass tape and disconnect the connector for the power cord assy. 4. Disconnect the connector for grand wire a assy. 5. Pull the power cord assy ...
Page 24
24 7.7. Upper frame 1. Remove 3 screws. 2. Remove the upper frame and the device body in order to disconnect the locks..
Page 25
25 7.8. P.C.Board b 1. Remove the screw and detach the p.C.B holder lid. 2. Disconnect 3 faston terminals and 2 connectors from p.C.Board b assy. 3. Remove 2 screws and detach p.C.B holder. 4. Remove the p.C.Board b assy from the p.C.B holder. * the p.C.Board b assy is held to the p.C.B holder with ...
Page 26
26 7.9. Heat insulator and grand wire a assy 1. Remove the bind wires a of the lead wires. 2. Move the non-flammable tubes a and c and disconnect the 2 faston terminals from the heater. 3. Remove the screw and detach the heat insurator. 4. Remove the screw, spring washer and hexagon nut and detach t...
Page 27
27 7.10. Sensor assy 1. Remove the screw and hexagon nut and detach the sen- sor assy from the heater case unit. Tips on assembly • insert the notched part of the sensor assy into the fixing square hole of heater case unit and screw the sensor assy to the heater case unit. 7.11. Pulley b, connector ...
Page 28
28 7.12. Heater case base assy and heater case unit 1. Remove the 4 screws and detach the heater case base assy. 2. Remove the heater case unit from the angle. Tips on assembly • set the positioning marks across from each other on the heater case side and on heater case base side. 7.13. Heater 1. Ta...
Page 29
29 7.14. Motor assy 1. Remove 4 screws and detach the motor assy. 7.15. Bread pan 1. Turn the bread pan upside down and remove 3 screws. 2. Remove the packing. Tips on assembly • set the positioning marks across from each other when assembling the mounting shaft assy and the bread pan. 7.16. Post-as...
Page 30: 8 Wiring Connection Diagram
30 8 wiring connection diagram 8.1. Schematic diagram.
Page 31
31 8.2. Basic wiring diagram.
Page 32
32 9 exploded view and replacement parts list 9.1. Parts location.
Page 33
33 9.2. Replacement parts list notes:important safety notice • components identified by mark have special characteristics important for safety. • " when replacing any of these components use only manufacturer's specified parts." model no.Sd-257-wst australia safety ref. No. Part no. Part name & desc...
Page 34
34 a xtb4+14bfc 4 x 14 binding head tapping screw 5 b xtt4+10bfc 4 x 10 truss head tapping screw 7 c xtb4+14bfj 4 x 14 binding head tapping screw 5 d xtb4+22bfj 4 x 22 binding head taptite screw 1 e xss4+8uw 4 x 8 flush head machine screw 3 f xsn4+8ffj 4 x 8 pan head machine screw 1 g x0227-031 moto...
Page 35
35 9.3. Packing instruction.