Vs102 electronic vibration switch provibtech phone: +1-713-830-7601 fax: +1-281-754-4972 pvt@provibtech.Com , www.Provibtech.Com 0 vs102 electronic vibration switch user manual installation, operation, maintenance provibtech, inc. 11011 brooklet drive, suite 360, houston, texas 77099, usa vs102-usr-...
Vs102 electronic vibration switch provibtech 1 table of content vs102 electronic vibration switch - introduction ....................................................................................... 2 specifications .....................................................................................
Vs102 electronic vibration switch provibtech 2 vs102 electronic vibration switch - introduction the vs102 electronic vibration switch is designed to be the cost effective solution for vibration switch applications. The vs102’s unique and rugged design is suitable for harsh environments and hazardous...
Vs102 electronic vibration switch provibtech 3 non-latching. Local reset: default is latching 9 alarm: dual dry contact relays; single dry contract relays; dual triac no; dual triac nc; single triac no; single triac nc;. The default is dual dry contact relays 9 alert high: default is 12.5mm/s 9 dang...
Vs102 electronic vibration switch provibtech 4 vs102 system installation installation - mechanical outline drawing supply.
Vs102 electronic vibration switch provibtech 5 note: the default case has no local reset..
Vs102 electronic vibration switch provibtech 6 installation – hardware vs102 has two different mounting plates and two different mounting studs. See figuration below. Be aware of that vs102 will sense the vibration in the vertical axis reference to the mounting plate..
Vs102 electronic vibration switch provibtech 7 installation – field-wiring diagram connector setting: danger _ + buf j1 0 4 j1 0 1 j1 0 2 j 105 j1 0 6 j 107 ok alert reset/set note: 1.Select relay/triac no/triac nc as per alarm option 2. If single alarm is selected, alert is valid only function desc...
Vs102 electronic vibration switch provibtech 8 vs102 operation vs102 display and status vs102 will have status indication: 9 buf: buffered output. 9 ok: green/red led. Normally green. With not ok or no power supply, the led is off. In bypass mode, the led is red. 9 alert: yellow led 9 danger: red le...
Vs102 electronic vibration switch provibtech 9 9 adjust alert: hold down reset/set button for 10s, ok led and alert led flash. Press reset/set button again, alert led flash and it changes into alert calibration mode. Three seconds later, the ampere meter displays the last set alert set-point (defaul...
Vs102 electronic vibration switch provibtech 10 vs102 maintenance order information vs102-abcd-efgg a: alarms*** a = 0: dual spdt relays a = 1*: single spdt relay a = 2: single spst triac, no a = 3: dual spst triacs, no a = 4: single spst triac, nc a = 5: dual spst triacs, nc b: conduit entries b = ...
Vs102 electronic vibration switch provibtech 11 alarm latching. E=2/e=3 default setting is alarm non-latching. Note: when user set 4-20ma outputs item to none, the instrument keeps current output of 3ma..
Vs102 electronic vibration switch provibtech 12 vs102 zero (4ma) calibration vs102 can be field calibrated with zero (4ma) 9 power on 9 connect a ampere meter to the 4-20ma terminal 9 adjust zero point: hold down reset/set button for 10seconds. Ok led and alert led flash and the instrument changes i...
Vs102 electronic vibration switch provibtech 13 mounting plate , mounting studs and accessories: 8-r5(0.2") 8(0.31") 135(5.3") 53(2.1") 6(0.24") 2-r3(0.12") 85(3.35") 165(6.5") 8(3.46") 165(6.5") 121(4.76") 121(4.76") 77.5(3.05") 20(0.79") φ108(4.25") 3/4"npt or m20×1.5 5(0.20") 25(0.98") mounting h...
Vs102 electronic vibration switch provibtech 14 trouble shooting 1. The instrument is not ok after powered on inspect whether its power supply is correct referring to the field wiring diagram; inspect whether the delay period expired. 2. The instrument has no 4-20ma output inspect whether its power ...
Vs102 electronic vibration switch provibtech 15 note: if the effect is not apparent, wind the wire around the magnetic ring in a circle as the following figure shows or install another magnetic ring adjacent to the first one as the above figures..
