1. DL manuals
  2. Proxel
  3. Transmitter
  4. EPS-DUAL
  5. Installation Instructions & User Manual

Proxel EPS-DUAL Installation Instructions & User Manual

Manual is about: Parking sensor

Summary of EPS-DUAL

  • Page 1

    Parking sensor mod. Eps-dual installation instructions & user manual.

  • Page 2

    - installation instructions ................................. Pag. 3 - user manual ................................................ Pag. 12 - electric schematic ....................................... Pag. 15 - kit components ........................................... Pag. 16 eps-dual can be instal...

  • Page 3: Installation Instructions

    Installation instructions 1.0 a) the installation of the antenna sensor, constituted by an aluminium adhesive ribbon, must be performed to the inside of the bumper. It is of some importance that the zone of application on the inside surface of the bumper corresponds to the higher part as regards the...

  • Page 4

    2. Starting procedure b) through the individuated passages route the connections cable inside the trunk or the engine van leaving the ecu outside. (fig. 2) fig. 2 pag. 4 central module + harness front bumper installation a) locate a passage where, from the outside at the extremity of the bumper,it i...

  • Page 5

    3.0 mounting the ecu and antenna sensor thoroughly clean with alcohol or nitro solvent (be carefull not to use antiadhesive detergent) the inner surface of the bumper of the zone previously identified (see fig.1) on which will be applied the antenna sensor and the central unit. Starting from the zon...

  • Page 6

    When the antenna sensor has been attached, covering the whole of the bumper from left to right, the excess length is cut off. Place a piece of the included sticking material at either ends of the antenna sensor to ensure a secure fixing onto the bumper. Its recommended (but not essential) to cover t...

  • Page 7

    Connect the small fastoned cable of the ecu to the antenna sensor. Apply a piece of sticking material on the unit and place it on the bumper by a strong pressure (if the ambient temperature is below 10 °c we recommend heating both the mastic and the sticking area on the bummper). It is advisable to ...

  • Page 8

    4.0 electrical connections front installation c) connect the two gray leads of the harness to the extension speaker cable (no polarity) and bring it inside the car. If your vehicle has a metal crash protection bar and the antenna will be within 2 cm's of this metal bar (once the bumper is re-fitted)...

  • Page 9

    Rear installation a) connect the red lead of the harness to the positive cable that feeds the reversing lamp. Connect the lead of the harness to the earth of the reversing lamp. -- it advisable not to connect to any other point of earth on the chassy of the car -- b) black c) connect the two gray le...

  • Page 10

    Pag. 10 5. Mounting the speaker a) mount the eps-dual speaker using the included adhesive mount in a proper place in order to ensure a good perception of sound by the driver. B) connect the extension wire to the speaker through its plug-in connector. 6. Final testing procedure a) turn on the key, in...

  • Page 11

    Pag. 11 warning: for a correct simulation reset the system every time you approach. C) if the system proves to work properly, you can remount the bumper. Nota: eps-dual s tarts to give the signaling only when the vehicle is being approached to the obstacle; a fixed object in front of the bumper, for...

  • Page 12: User Manual

    Pag. 12 user manual 1.Operating principle eps-dual is an innovative parking sensor that uses low energy electromagnetic waves and is able to detect the approach of any kind of obstacle . The activation of the device isobteined by the insertion of the back gear or by pressing the activation button (i...

  • Page 13

    Pag. 13 1) an increase in sequence of "bip"(alert) inform the driver that an obstacle is approaching. 2) intermittent sounds of fast repetition rate (alarm) when the obstacle comes close to the bumper at a distance between 15 and 30 cm. 3) continuous sound at a more acute frequency (risk of contact)...

  • Page 14

    Pag. 14 2. During the test you must also take into consideration the fact that, after the first approach to the bumper, any subsequent approach without first reset the system , can give false interpretations of the functionality of the sensor due to special characteristics of the eps-dual software s...

  • Page 15

    Pag. 15 block schematic for front or back installation to back gear lamp or push-button switch to ground + buzzer antenna sensor - central unit + harness technical characteristics - operating range from 9,5 to 18v - max current absorption 70 ma - operating temperature from -20 to +90 °c - averange d...

  • Page 16

    Proxel s.R.L. -via val della torre 39 -10149 - torino ( italy) - tel. +39 011 296022 - fax +39 011 2218053 technical info: eps@proxel.Com central module + harness sticking material buzzer buzzer wire antenna sensor push button.