- DL manuals
- PS Engineering
- Recording Equipment
- PMA8000BTi
- Installation and operation manual
PS Engineering PMA8000BTi Installation and operation manual - page 6
PS Engineering
PMA8000BTi IntelliAudio Audio Selector Panel and Intercom System
Installation and Operator’s Manual
200-890-1722
Page 1-3
Rev. 1, March 2016
Audio Selector Specifications
Audio selector panel input impedance:
510
Input Isolation:
-60 dB (min.)
Speaker Muting:
-60 dB (min.)
Speaker Output (into 4 ) with no clipping
14 VDC:
28 VDC:
3 Watts (min.)
10 Watts (min.)
Receiver Inputs:
9 (Com 1, Com 2, TEL, Nav 1, Nav 2, ADF, DME,
MKR, AUX)
Unswitched Inputs:
5 (including front jack)
Transmitter Selections:
4 (Com 1, Com 2, TEL
Com1/2)
Speaker Impedance:
4
Headphone Impedance:
150 – 1000
Headphone Output:
38 mW each headset, no clipping
Microphone Impedance:
150 - 600
Bluetooth Radio
Class 3, FCC ID
QOQWT32AE
Intercom Specifications
Intercom Positions:
6 places (with individual IntelliVox® circuits)
Music Inputs:
2, (Independent, Stereo)
Music Muting:
>-30 dB "Soft Mute" when Com or intercom active.
Distortion:
Mic Freq. Response, 3 dB:
300 Hz - 6000 Hz
Music Freq. Response, 3 dB:
10 Hz – 26 kHz
MARKER BEACON RECEIVER:
Frequency:
75 MHz Crystal Controlled
Sensitivity:
Low:
High:
Capable of: (preset at factory for field application)
1000 Volts (Hard) (360 to 570 V soft)
200 Volts (Hard) (130 to 200 V soft)
Selectivity:
-6 dB at ±10 kHz
-40 dB at ±120 kHz
External Lamp Output:
7.5 (±4 VDC unloaded, at maximum brightness) VDC
positive when active, max. current 125 mA
MM Sense:
Active high (4.5 ± 1.0VDC)
Summary of PMA8000BTi
Page 1
9800 martel road lenoir city, tn 37772 www.Ps-engineering.Com p p m m a a 8 8 0 0 0 0 0 0 b b t t i i document p/n 200-890-1722 revision 1, march 2016 audio selector panel with marker beacon receiver high-fidelity stereo intercom system installation and operation manual faa- tso c50c, c35d easa etso...
Page 2
Table of contents section i – general information................................................................ 1-1 1.1 introduction............................................................................................................................ 1-1 1.2 scope ..............................
Page 3
Ps engineering pma8000bti intelliaudio audio selector panel and intercom system installation and operator’s manual 200-890-1722 page ii rev. 1, march 2016 2.12.1 r equired t est e quipment ........................................................................................ 2-12 2.12.2 a udio p a...
Page 4
Ps engineering pma8000bti intelliaudio audio selector panel and intercom system installation and operator’s manual 200-890-1722 page 1-1 rev. 1, march 2016 section i – general information 1.1 introduction the pma8000bti represents another evolutionary step in cockpit audio control and intercommunica...
Page 5
Ps engineering pma8000bti intelliaudio audio selector panel and intercom system installation and operator’s manual 200-890-1722 page 1-2 rev. 1, march 2016 a 3-light, 75 mhz marker beacon receiver is integrated in the pma8000bti. This provides the necessary marker beacon lights and audio indications...
Page 6
Ps engineering pma8000bti intelliaudio audio selector panel and intercom system installation and operator’s manual 200-890-1722 page 1-3 rev. 1, march 2016 audio selector specifications audio selector panel input impedance: 510 input isolation: -60 db (min.) speaker muting: -60 db (min.) speaker o...
Page 7
Ps engineering pma8000bti intelliaudio audio selector panel and intercom system installation and operator’s manual 200-890-1722 page 1-4 rev. 1, march 2016 1.6 equipment supplied 1 ea. Of the following units: model description part number pma8000bti pma8000bt audio panel with intelliaudio, marker, s...
Page 8
Ps engineering pma8000bti intelliaudio audio selector panel and intercom system installation and operator’s manual 200-890-17221722 page 2-1 rev. 1, march 2016 section ii - installation 2.1 general information 2.1.1 scope this section provides detailed installation and interconnection instructions f...
Page 9
Ps engineering pma8000bti intelliaudio audio selector panel and intercom system installation and operator’s manual 200-890-17221722 page 2-2 rev. 1, march 2016 2.3.4 audio panel tray and connector assembly the rack connectors mate with two 44-pin connectors in the pma8000bti. The connectors are a su...
Page 10
Ps engineering pma8000bti intelliaudio audio selector panel and intercom system installation and operator’s manual 200-890-17221722 page 2-3 rev. 1, march 2016 ground connections are made directly to the dedicated music signal and ground inputs on the pma8000bti. The power for ife and audio panel sh...
Page 11
Ps engineering pma8000bti intelliaudio audio selector panel and intercom system installation and operator’s manual 200-890-17221722 page 2-4 rev. 1, march 2016 some avionics do not provide a separate audio low, and may introduce additional electrical noise into the system. For best results, connect ...
Page 12
Ps engineering pma8000bti intelliaudio audio selector panel and intercom system installation and operator’s manual 200-890-17221722 page 2-5 rev. 1, march 2016 note inputs 1, 2 and 4 are fixed (1:1), and any audio level adjustments must be made at the input source. Unswitched #3 has a variable adjus...
Page 13
Ps engineering pma8000bti intelliaudio audio selector panel and intercom system installation and operator’s manual 200-890-17221722 page 2-6 rev. 1, march 2016 fcc regulation 47 cfr § 22.925 prohibition on airborne operation of cellular telephones. Cellular telephones installed in or carried aboard ...
Page 14
Ps engineering pma8000bti intelliaudio audio selector panel and intercom system installation and operator’s manual 200-890-17221722 page 2-7 rev. 1, march 2016 figure 2-3 jumper locations 4. Place the lid back on the unit, aligning holes. 5. Install and tighten qty. 4 long thread screws into the lid...
Page 15
Ps engineering pma8000bti intelliaudio audio selector panel and intercom system installation and operator’s manual 200-890-17221722 page 2-8 rev. 1, march 2016 2.4.13 pa mute (j2, pin 12) pin 12 of j2 is a ttl logic output that is active low during ptt operation. 2.4.14 miscellaneous logic output (j...
Page 16
Ps engineering pma8000bti intelliaudio audio selector panel and intercom system installation and operator’s manual 200-890-17221722 page 2-9 rev. 1, march 2016 2.5.2.1 entertainment 2 mute (j2 pin 13 & 14) connecting j2 pin 13 to pin 14 (or ground) through a spst switch places the entertainment #2 m...
Page 17
Ps engineering pma8000bti intelliaudio audio selector panel and intercom system installation and operator’s manual 200-890-17221722 page 2-10 rev. 1, march 2016 2.7 adjustments the pma8000bti is factory adjusted to accommodate the typical requirements for most aircraft configura- tions. There are th...
Page 18
Ps engineering pma8000bti intelliaudio audio selector panel and intercom system installation and operator’s manual 200-890-17221722 page 2-11 rev. 1, march 2016 2.9 pma8000bti pin assignments j1 function j2 function 1 mkr ant 1 pilot phones low 2 mkr ant low 2 copilot phones low 3 telephone audio in...
Page 19
Ps engineering pma8000bti intelliaudio audio selector panel and intercom system installation and operator’s manual 200-890-17221722 page 2-12 rev. 1, march 2016 2.10 wiring checkout after wiring is complete, verify power is only on pins 8 and 9 of the j2 and airframe ground on connect- or pins 10 an...
Page 20
Ps engineering pma8000bti intelliaudio audio selector panel and intercom system installation and operator’s manual 200-890-17221722 page 2-13 rev. 1, march 2016 15. Push both the rcv buttons at the same time to activate the intelliaudio™ function. Verify that the audio from com 1 is present in the 1...
Page 21
Ps engineering pma8000bti intelliaudio audio selector panel and intercom system installation and operator’s manual 200-890-17221722 page 2-14 rev. 1, march 2016 cables and coaxial cables. Verify that the cables are not exposed to any sharp edges or rough surfaces, and that all contact points are pro...
Page 22
Ps engineering pma8000bti audio selector panel and intercom system installation and operator’s manual 200-890-1722 page 3-1 rev. 1, march 2016 section iii operation 3.1 scope this section provides detailed operating instructions for the ps engineering pma8000bti, audio selector panel/marker beacon r...
Page 23
Ps engineering pma8000bti audio selector panel and intercom system installation and operator’s manual 200-890-1722 page 3-2 rev. 1, march 2016 copilot it transmitting, and the pilot presses his ptt, the pilot’s microphone will be heard over the selected com transmitter. In tel mode, the pilot microp...
Page 24
Ps engineering pma8000bti audio selector panel and intercom system installation and operator’s manual 200-890-1722 page 3-3 rev. 1, march 2016 3.4 telephone (tel) (9) the tel mode serves as a full duplex interface and distribution for telephone systems such as aircell or portable cellular phones wit...
Page 25
Ps engineering pma8000bti audio selector panel and intercom system installation and operator’s manual 200-890-1722 page 3-4 rev. 1, march 2016 adjust the volume level, there is a service adjustment located on the top of the unit. A pushbutton is used to set the receiver sensitivity and to test the i...
Page 26
Ps engineering pma8000bti audio selector panel and intercom system installation and operator’s manual 200-890-1722 page 3-5 rev. 1, march 2016 the outer volume control knob controls intercom volume for the passengers. It has no effect on radio or music levels. Adjust the radios and intercom volume f...
Page 27
Ps engineering pma8000bti audio selector panel and intercom system installation and operator’s manual 200-890-1722 page 3-6 rev. 1, march 2016 §91.21 “(a) except as provided in paragraph (b) of this section, no person may operate, nor may any opera- tor or pilot in command of an aircraft allow the o...
Page 28
Ps engineering pma8000bti audio selector panel and intercom system installation and operator’s manual 200-890-1722 page 3-7 rev. 1, march 2016 crew of aircraft must not be operated while such aircraft are airborne (not touching the ground). When any air- craft leaves the ground, all cellular telepho...
Page 29
Ps engineering pma8000bti audio selector panel and intercom system installation and operator’s manual 200-890-1722 page 3-8 rev. 1, march 2016 note the front jack is no substitute for the certified installation of alerts such as the gps waypoint or autopilot tones. These still must be hard wired int...
Page 30
Ps engineering pma8000bti audio selector panel and intercom system installation and operator’s manual 200-890-1722 page 3-9 rev. 1, march 2016 3.11.1 “intercom” alternate intercom function (a) this function controls the distribution of aircraft radio within the intercom, as well as passenger interco...
Page 31
Ps engineering pma8000bti audio selector panel and intercom system installation and operator’s manual 200-890-1722 page 3-10 rev. 1, march 2016 the pilot can hear this music source in iso mode, if desired, as follows: in the iso mode, hold the (music) button, and press the ics mode button for more t...
Page 32
Ps engineering pma8000bti audio selector panel and intercom system installation and operator’s manual 200-890-1722 page 3-11 rev. 1, march 2016 3.12 bluetooth® interface the pma8000bti has a bluetooth interface. The audio panel is always “discoverable,” so you just need to search for the pma8000bt f...
Page 33
Ps engineering pma8000bti audio selector panel and intercom system installation and operator’s manual 200-890-1722 page 3-12 rev. 1, march 2016 figure 3-3 playback controls ps engineering pma8000bti audio selector panel and intercom system installation and operator’s manual 200-890-1722 page 3-12 re...
Page 34
Ps engineering pma8000bti audio selector panel and intercom system installation and operator’s manual 200-890-1722 page 4-1 rev. 1, march 2016 section iv – warranty and service 4.1 warranty in order for the factory warranty to be valid, the installations in a certified aircraft must be accomplished ...
Page 35
Ps engineering pma8000bti audio selector panel and intercom system installation and operator’s manual 200-890-1722 appendix a rev. 1, march 2016 appendix a – external ptt hook up part of the installation includes the installation of ptt (push to talk) switches that allow the use of your aircraft rad...
Page 36
Ps engineering pma8000bti audio selector panel and intercom system installation and operator’s manual 200-890-1722 rev. 1, march 2016 appendix b – pma8000 installation drawings j2 j1 viewed from back 15 30 44 1 16 31 15 30 44 1 16 31 ground lug ground lug 475-440-0001 (x2) back plate assy 475-009-00...
Page 37
Ps engineering pma8000bti audio selector panel and intercom system installation and operator’s manual 200-890-1722 appendix c rev. 1, march 2016 appendix c – j1 connector interconnect com 1 audio hi com 1 mic key com 1 lo communications transceiver #1 communications transceiver #2 nav 1 audio hi nav...
Page 38
Ps engineering pma8000bti audio selector panel and intercom system installation and operator’s manual 200-890-1722 appendix d rev. 1, march 2016 appendix d – j2 connector interconnect 22 20 31 16 1 35 36 24 23 25 4 3 2 copilot phones (r) copilot phones (l) copilot phones lo pass. 1 mic jack pass. Mi...
Page 39
Ps engineering pma8000bti audio selector panel and intercom system installation and operator’s manual 200-890-1722 appendix e rev. 1, march 2016 appendix e – instructions for faa form 337 and continuing air- worthiness 9.1 instructions for faa form 337, audio panels one method of airworthiness appro...
Page 40
Ps engineering pma8000bti audio selector panel and intercom system installation and operator’s manual 200-890-1722 appendix f rev. 1, march 2016 appendix f – rtca do160d environmental qualification form audio selector panel/intercom/marker beacon receiver part number: 050-890-( ) faa tso number: c50...